Ubiquiti airMAX Titanium Sector AM-V2G-Ti Quick Start Manual
Mid-gain advanced rf isolation variable beamwidth antenna
Hide thumbs
Also See for airMAX Titanium Sector AM-V2G-Ti:
- Quick start manual (21 pages) ,
- Quick start manual (21 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ubiquiti airMAX Titanium Sector AM-V2G-Ti
Summary of Contents for Ubiquiti airMAX Titanium Sector AM-V2G-Ti
- Page 1 Mid-Gain Advanced RF Isolation Variable Beamwidth Antenna Model: AM-V5G-Ti...
-
Page 2: Package Contents
(M8, Qty. 8) Products may be different from pictures and are subject to change without notice. TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet cable and earth grounding must be used as conditions of product warranty. TOUGHCable is designed for outdoor installations. -
Page 3: Installation Requirements
Ethernet connections and should be grounded through the AC ground of the PoE. We recommend that you protect your networks from the most brutal environments and devastating ESD attacks with industrial-grade shielded Ethernet cable from Ubiquiti Networks. For more details, visit www.ubnt.com/toughcable Hardware Overview Adjustable... -
Page 4: Hardware Installation
Hardware Installation 1. Set the desired beamwidth by adjusting the Beamwidth Deflectors. Use a 3 mm hex key driver to loosen the four hex head screws, but do not remove the screws. 2. Carefully move the Beamwidth Deflectors to the desired angle, as indicated by the screw slots. - Page 5 4. Attach the RF Cables to the connectors labeled Chain 0 and Chain 1 on the RocketM5. 5. Attach the RocketM5 to the Rocket Mounting Bracket. a. Align the mounting tabs on the back of the RocketM5 with the four mounting slots on the bracket. b.
- Page 6 6. Connect the other ends of the RF Cables to the RF connectors on the antenna. 7. Slide the Protective Shroud down over the RocketM5 until it locks onto the Rocket Mounting Bracket. Note: If you have trouble locking the shroud into place, try adjusting the placement of the RF Cables.
- Page 7 8. Attach the U-Brackets to the antenna: a. Secure the slotted U-Bracket to the upper Mounting Lugs of the antenna using two Serrated Flange Nuts. b. Secure the other U-Bracket to the lower Mounting Lugs of the antenna using two Serrated Flange Nuts. Note: Orient both U-Brackets as shown below.
- Page 8 9. Insert two Carriage Bolts into each Pole Bracket. 10. Attach each Pole Bracket to each U-Bracket using two Serrated Flange Bolts. Hand-tighten only.
- Page 9 11. To mount the antenna to the pole, slide a Pole Clamp over each pair of Carriage Bolts. Secure each Pole Clamp with two Serrated Flange Nuts. Note: The mounting assembly can accommodate a Ø 1.5" - 3.0" pole.
- Page 10 12. The antenna has an electrical downtilt of 2°. To further adjust the elevation angle: a. Loosen the four Serrated Flange Bolts on the U-Brackets and the two Serrated Flange Nuts on the upper Pole Clamp. b. Slide the antenna to the desired tilt. (The brackets may slide along the pole, depending on the angle of the elevation tilt.) c.
-
Page 11: Specifications
Specifications Model: AM-V5G-Ti Dimensions 721 x 149.1 x 75.7 mm Weight 3.72 kg (with Brackets) Frequency Range 5.45 - 5.85 GHz Beamwidth Angles 60°/ 90°/ 120° Gain 21 dBi @ 60° (Beamwidth Dependent) 20 dBi @ 90° 19 dBi @ 120° Electrical Downtilt 2°... -
Page 12: Safety Notices
Safety Notices Read, follow, and keep these instructions. Heed all warnings. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. -
Page 13: Limited Warranty
(VI) has no original Ubiquiti MAC label, or is missing any other original Ubiquiti label(s). (VII) has not been received by Ubiquiti within 30 days of issuance of the RMA. - Page 14 SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS, DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY OF THE FOREGOING.
- Page 15 Note Some countries, states and provinces do not allow exclusions of implied warranties or conditions, so the above exclusion may not apply to you. You may have other rights that vary from country to country, state to state, or province to province. Some countries, states and provinces do not allow the exclusion or limitation of liability for incidental or consequential damages, so the above limitation may not apply to you.
- Page 16 RoHS/WEEE Compliance Statement English European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams.
- Page 17 Español La Directiva 2002/96/CE de la UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
-
Page 18: Declaration Of Conformity
UBIQUITI NETWORKS device, megfelel a vonatkozó alapvetõ [Hungarian] követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Íslenska Hér me l sir UBIQUITI NETWORKS yfir ví a UBIQUITI NETWORKS device, er í samræmi vi grunnkröfur og a rar kröfur, sem ger ar eru í [Icelandic] tilskipun 1999/5/EC. -
Page 19: Online Resources
NETWORKS device, è conforme ai requisiti essenziali ed alle altre [Italian] disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski Ar o UBIQUITI NETWORKS deklar , ka UBIQUITI NETWORKS device, atbilst Direkt vas 1999/5/EK b tiskaj m pras b m un citiem ar to saist [Latvian] tajiem noteikumiem. - Page 20 . u b n t . c o m © 2012-2013 Ubiquiti Networks, Inc. All rights reserved. J060713—720-00049-01...