Page 1
空氣清新機 使用說明書 “Plasmacluster” and “Device of a cluster of grapes” are trademarks of Sharp Corporation. *The number in this technology mark indicates an approximate number of ions supplied into air of 1 cm which is measured around the center of a room with the “high-density plasmacluster 7000”...
Page 2
Please read before operating your new Air Purifier The air purifier draws in room air from the air intake, passes the air through a Pre- Filter, a Active Carbon Deodorizing Filter and a HEPA Filter inside of the unit, then discharges the air through the air outlet.
Sensor Technology continuously monitors air quality, and automatically adjusting airflow based on detected air purity. Thank you for purchasing the SHARP Air Purifier. Please read this manual carefully. Before using this product, be sure to read the section: “Important Safety Instructions.”...
• Be cautious when cleaning the unit. Corrosive cleansers may damage the exterior. • Only a Sharp Authorized Service Centre should service this air purifier. Contact the nearest Service Centre for any problems, adjustments, or repairs.
Page 5
CAUTIONS CONCERNING OPERATION • Do not block the air intake and/or air outlet. • Do not use the unit near or on hot objects, such as stoves or heaters or where it may come into contact with steam. • Do not lay the unit down when using. •...
PART NAMES FRONT DUST SIGN Indicates the air purity of the room in 3 levels with color changes. Green Clean Orange PLASMACLUSTER SIGN Blue Plasmacluster ON Impure Plasmacluster OFF BACK Main Unit Dust sensor / Dust Sensor Filter Air Outlet HEPA Filter OFF TIMER Button / Active Carbon Deodorizing Filter...
FILTER INSTALLATION Be sure to remove the power plug from the wall outlet. To maintain the quality of the filter, it is installed in the main unit and packed in plastic bag. Be sure to remove the filter from the plastic bag before using the unit. Replace the Back Panel to the Remove the Back Panel.
OPERATION CLEAN AIR START STOP • Select the desired fan speed. • Unless the power cord has been unplugged, the operation starts in the previous mode it was operated in. CLEAN ION SHOWER Releases high-density Plasmacluster ions and discharges strong air flow for 60 minutes. START NOTE •...
Page 9
OFF TIMER Select the time turning off the unit during operation. The unit automatically stops once the selected time is reached. ● 2h ● 4h ● 8h CANCEL Light Control You can turn OFF the DUST/PLASMACLUSTER SIGN when they are lighting up. NOTE •...
CARE AND MAINTENANCE To maintain optimum performance of this air purifier, please clean the unit including the filter periodically. Be sure to disconnect the power cord from the wall outlet before performing any maintenance. BACK PANEL (Pre-filter) Gently remove dust from the back panel by using a vacuum cleaner attachment or similar tool.
Page 11
Be sure to remove the power plug from the wall outlet. UNIT Wipe with a dry, soft cloth For stubborn stains or dirt, use a soft cloth dampened with warm water. CAUTION • Do not use volatile fluids Benzene, paint thinner, polishing powder, etc., may damage the surface. •...
TROUBLESHOOTING Before calling for service, please review the Troubleshooting chart below, since the problem may not be a unit malfunction. SYMPTOM REMEDY (not a malfunction) Odors and smoke are not removed. • Replace the filters if they appear to be heavily soiled. (E-9) The DUST SIGN illuminates green •...
SPECIFICATIONS Power Supply 220V 50Hz Fan Speed SLEEP Speed Rated Power (W) Operation Airflow (m /hr) 54~96 Applicable Floor Area (m High density Plasmacluster ion recommended room size (m Cord Length (m) Dimensions (mm) 383(W) x 209(D) x 540(H) Weight (kg) *1 The fan speed is automatically switched depending on the amount of impurities in the air.
Need help?
Do you have a question about the FP-F40A and is the answer not in the manual?
Questions and answers