Advertisement
4. OPERATION
4.1.
Ensure the direction selector (fig.1) is in the mid (lock) position.
4.2.
Insert the required driver bit into the chuck by pulling the locking collar forward and sliding the bit in until the locking ring snaps
back.
4.3.
Select clockwise or anticlockwise direction by means of the direction selector.
4.4.
Select speed using the button at the base. When going forward light will illuminate indicating 1, 2 or 3 Options:
1 = low power, 3 = full power. When in reverse, light illuminates = half power, light off = full power.
4.5.
Squeeze the trigger to start the driver; initial pressure switches on the LED worklight, further pressure starts the motor and
increases speed.
4.6.
To release the bit, pull the locking collar forward and withdraw.
5. MAINTENANCE
WARNING: Always disconnect the battery before carrying out any inspection, maintenance or cleaning.
‰
5.1.
GENERAL INSPECTION
5.1.1.
Regularly check that all the fixing screws are tight. Repairs should be carried out by an authorised service centre.
5.2.
CLEANING
WARNING: Always wear protective equipment including eye protection and gloves when cleaning this tool.
‰
5.2.1.
Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and shorten the device's service life.
5.2.2.
Clean the body of your machine with a soft brush, or dry cloth.
5.2.3.
Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient, a mild detergent on a damp cloth is recommended.
5.2.4.
Water must never come into contact with the tool. Ensure the tool is thoroughly dry before using it.
5.2.5.
If available, use clean, dry, compressed air to blow through the ventilation holes (where applicable).
5.3.
LUBRICATION
5.3.1.
Slightly lubricate all moving parts at regular intervals with a suitable spray lubricant.
5.4.
STORAGE
5.4.1.
Store this tool carefully in a secure, dry place out of the reach of children.
‰
This tool may cause Hand Arm Vibration Syndrome if its use is not managed adequately.
This tool is subject to the vibration testing section of the Machinery Directive 2006/42/EC.
This tool is to be operated in accordance with these instructions.
Measured vibration emission value (a):
Uncertainty value (k):
1.5 m/s²
Please note that the application of the tool to a sole specialist task may produce a different average vibration emission. We recommend that
a specific evaluation of the vibration emission is conducted prior to commencing with a specialist task.
A health and safety assessment by the user (or employer) will need to be carried out to determine the suitable duration of use for each tool.
NB: Stated Vibration Emission values are type-test values and are intended to be typical.
Whilst in use, the actual value will vary considerably from and depend on many factors.
Such factors include; the operator, the task and the inserted tool or consumable.
NB: ensure that the length of leader hoses is sufficient to allow unrestricted use, as this also helps to reduce vibration.
The state of maintenance of the tool itself is also an important factor, a poorly maintained tool will also increase the risk of Hand Arm Vibration
Syndrome.
Health surveillance.
We recommend a programme of health surveillance to detect early symptoms of vibration injury so that management procedures
can be modified accordingly.
Personal protective equipment.
We are not aware of any personal protective equipment (PPE) that provides protection against vibration injury that may result from the
uncontrolled use of this tool. We recommend a sufficient supply of clothing (including gloves) to enable the operator to remain warm and dry and
maintain good blood circulation in fingers etc. Please note that the most effective protection is prevention, please refer to the Correct Use and
Maintenance section in these instructions. Guidance relating to the management of hand arm vibration can be found on the HSE website
www.hse.gov.uk - Hand-Arm Vibration at Work.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 36 months labour and two years parts warranty from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
WARNING! – Risk of Hand Arm Vibration Injury.
3.854 m/s²
01284 703534
sales@sealey.co.uk
Original Language Version
www.sealey.co.uk
CP20VIDX Issue 3 (2,3) 15/07/21
Advertisement
