Daikin Altherma FWXV10AATV3 Installation Manual

Daikin Altherma FWXV10AATV3 Installation Manual

Hide thumbs Also See for Altherma FWXV10AATV3:

Advertisement

INSTALLATION MANUAL
Daikin Altherma
Heat pump convector
FWXV10AATV3(R)
FWXV15AATV3(R)
FWXV20AATV3(R)
FWXM10AATV3(R)
FWXM15AATV3(R)
FWXM20AATV3(R)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Altherma FWXV10AATV3 and is the answer not in the manual?

Questions and answers

Summary of Contents for Daikin Altherma FWXV10AATV3

  • Page 1 INSTALLATION MANUAL Daikin Altherma Heat pump convector FWXV10AATV3(R) FWXV15AATV3(R) FWXV20AATV3(R) FWXM10AATV3(R) FWXM15AATV3(R) FWXM20AATV3(R)
  • Page 2 By following the suggestions contained in this manual, the product you have purchased will operate without problems giving you optimum room temperatures with minimum energy costs. DAIKIN EUROPE N.V. Conformity This unit complies with European directives: •...
  • Page 3: Table Of Contents

    General General warnings ..............4 Fundamental safety rules .
  • Page 4: General

    Do not leave the room closed for long periods. declaration of conformity to the client in respect of the Periodically open the windows to ensure a correct laws in force and the indications given by DAIKIN in the change of air. instructions leaflet supplied together with the appliance.
  • Page 5: Product Range

    Product range There are 2 types of DAIKIN heat pump convectors, FWXV and FWXM, each of which is offered in 3 sizes with different performances and dimensions. FWXV-series FWXM-series cooler-convector with metal cabinet.
  • Page 6: Overall Dimensions

    GENERAL Overall dimensions 2 pipes U.M. FWXV10AATV3(R) FWXV15AATV3(R) FWXV20AATV3(R) Dimensions 1199 1399 FWXV 135 mm U.M. FWXM10AATV3(R) FWXM15AATV3(R) FWXM20AATV3(R) Dimensions FWXM...
  • Page 7: Installation

    (R) are exactly the same. DAIKIN EUROPE N.V. shall not respond for any damage to Only the images are to be considered as a mirror image. persons, animals or property.
  • Page 8: Access To The Internal Components

    INSTALLATION Access to the internal components To access the inside of the machine, follow the procedures Remove the front grill: below. - extract the grill until it is completely out of the seat - tilt the grill Remove the upper grill: - slide outwards - loosen the fixing screws of the upper grill - remove the grill...
  • Page 9: Removing The Side Panels

    INSTALLATION Removing the side panels To remove the side: Side - remove the sides upwards Machine body Vertical installation Using the paper template, trace the position of the two Mount the unit, checking that it fits correctly onto the fixing brackets on the wall. Use a suitable drill to make the brackets and checking that it is stable.
  • Page 10: Horizontal Or Ceiling Installation

    INSTALLATION Horizontal or ceiling installation Using the paper template, trace on the ceiling the position installation FWXV-series, horizontal of the two fixing brackets and the two rear screws. Using condensation collection basin accessory kits are available a suitable drill, make the holes and insert the wall plugs (2 EKM(10/15/20)COH.
  • Page 11: Condensation Discharge

    INSTALLATION Condensation discharge The condensation discharge network must be suitably If there is a height difference that could interfere with sized and the pipeline positioned so that it keeps a the outflow of the condensation, a pump must be constant inclination, never less than 1%. In the vertical mounted: installation, the discharge pipe is connected directly to in a vertical installation mount the pump under the...
  • Page 12: Filling The System

    INSTALLATION Mounting the condensation discharge pipe in the horizontal version To mount the horizontal bowl on the FWXM-series refer to N.B. for the horizontal installation carefully note the the instructions in kits EKM(10/15/20)COH. following precautions: check that the "L" pipe and the flexible rubber hose make sure that the machine is installed perfectly level are correctly connected to the bowl.
  • Page 13: Electrical Connections

    INSTALLATION 2.12 Electrical connections Make electrical connections according to the requirements The unit must be connected to the mains through a set out in sections General Warnings and Fundamental multipolar switch with minimum contact opening of at Safety Rules by reference to the patterns present in the least 3mm or with a device that allows the complete installation and accessories manuals.
  • Page 14: Cleaning Air Suction Filter

    INSTALLATION 2.15 Cleaning air suction filter After a period of continuous operation and in consideration he intends to restart the unit after a period of inactivity, of the concentration of impurities in the air, or when proceed as described. Extraction of filter cells To remove the grill: then remove the filter by pulling it outwards lift the grill until it is completely released from the seat...
  • Page 15: Energy Saving Tips

    INSTALLATION Cleaning filtering seats suck up the dust with a vacuum cleaner The appliance is fitted with a safety switch that wash the filter with running water without using prevents the operation of the fan with the mobile panel detergents or solvents, and leave to dry. missing or out of position.
  • Page 16: Troubleshooting

    INSTALLATION TROUBLESHOOTING Troubleshooting The ventilation does not activate even if there is hot or In case of water leaks or anomalous functioning cold water in the hydraulic circuit. immediately cut off the power supply and close the The appliance leaks water during the heating function. water taps.
  • Page 17 INSTALLATION Effect Cause Remedy The condensation bowl is blocked. Slowly pour a bottle of water in the low part of the battery to check the The condensation discharge does not drainage; if necessary, clean the bowl The appliance leaks water only during need an inclination for correct drainage.

Table of Contents