Unplugging and plugging the connectors dur- ing power-on mode may damage the ICs inside the unit. 2. To protect the pickup unit from electrostatic dis- charge during serviving, take an appropriate treat- ment(shorting-solder) by referring to "the DISAS- SEMBLY" on page 56. DEH-P560MP/XM/UC...
Page 3
By following the instructions in this manual, be sure to apply the prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed ones should be used. DEH-P560MP/XM/UC...
• Screw adjacent to mark on the product are used for disassembly. • For the applying amount of lobricants or glue, follow the instructions in this manual. (In the case of no amount instructions,apply as you think it appropriate.) 2.1 PACKING(DEH-P560MP/XM/UC) PACKING(DEH-P560MP/XM/UC) SECTION PARTS LIST Mark No. Description Part No.
Page 11
CNM7935 Cord Assy See Contrast table(2) See Contrast table(2) Insulator CNM8174 Remote Control Unit CXC3173 Cushion CNM8890 Cover CNS7068 Panel CNS6935 Holder Unit CXB6681 CD Mechanism Module(S10CODE2)CXK5665 Screw ISS26P055FTC Cable XDE7002 Tuner Amp Unit See Contrast table(2) Screw ASZ26P060FTC DEH-P560MP/XM/UC...
Page 12
(2) CONTRAST TABLE DEH-P560MP/XM/UC and DEH-P5650MP/XM/ES are constructed the same except for the following: Mark Description DEH-P560MP/XM/UC DEH-P5650MP/XM/ES Tuner Amp Unit XWM7020 XWM7017 Connector(CN161) CKS4124 Not used Holder CND1270 CND1477 Detachable Assy XXA7032 XXA7033 Keyboard Unit XWM7039 XWM7036 Sub Grille Assy...
DSCSNS Q652 HOME VDCONT CD3VON 46 HOME VDCONT CLAMP 12EJ DISC SENSE SENSE SENSE SENSE +3.3V REGULATOR IC 703 IC 203 3VDD V3R3D NJM2391DL1-33 Q650 S-812C33AUA-C2N DETACH SENS +3.3V REGULATOR V1R5 IC 501 V3R3D Q653 CD3VON S-L2980A15MC-C6A +1.5V REGULATOR DEH-P560MP/XM/UC...
Page 17
DEH-P560MP/XM/UC CN351 RESET REAR L Q351 IC 602 S-80835CNUA-B8U CN352 NON-FAD/SW L Q353 tunpce@ FRONT L TUNPCE1 TUNPDI Q352 TUNPDO VDD REGULATOR TUNPCK Q911 Q913 SYSTEM CONTROLLER IC 601(1/2) PD5919A DALMON CN901 BACKUP SENSE FUSE bsens BACK UP Q931 asens...
Code Practical value 0.01uF 12k ohms 101/10 100uF/10V 10k ohms The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. DEH-P560MP/XM/UC...
Page 19
CD:+10.46dBs > AM: -1.7dBs IP-BUS:+8.5dBs CD:+9.66dBs SUB WOOFER R ch SUB WOOFER L ch 600µH SYSTEM CONTROLLER > FUSE CEK1208 BACK UP DETACH SENSE FM:+33.6dBs AM:+25.1dBs VDD REG. IP-BUS:+35.3dBs CD:+36.46dBs BACK B.UP SENSE ILM SENSE ACC SENSE TEL MUTE DEH-P560MP/XM/UC...
Page 20
FM(100%):-19.5dBs FM/AM TUNER UNIT AM(30%):-30.0dBs DEH-P560MP/XM/UC...
Page 32
7 SIN 500mV/div 200mV/div 1V/div @ TE 500mV/div 9 TIN 500mV/div CD-ROM play operation(Regular track Jump) Spindle waveform during play operation Spindle waveform during play operation (Wider) Ref.: Ref.: Ref.: REFO REFO REFO Mode: Mode: Mode: Normal Normal Normal DEH-P560MP/XM/UC...
Page 33
500mV/div 4 LOEJ 3 12SNS 9 TIN 5V/div 5V/div 500mV/div 4 LOEJ 5V/div 12 cm CD Eject operation 8 cm CD Eject operation CD-DA >> CD-ROM mode change(Band key) Ref.: Ref.: Ref.: REFO Mode: Mode: Mode: Normal Normal Normal DEH-P560MP/XM/UC...
Page 34
% RFAGC 1V/div 500ms/div 1V/div 500µs/div 8 CIN 9 TIN 500mV/div 1V/div 9 TIN @ TE 500mV/div 1V/div 0 FIN 1V/div CD-ROM >> CD-DA mode change(Band key) Black dot(800µm) during play Ref.: Ref.: REFO REFO Mode: Mode: Normal Normal DEH-P560MP/XM/UC...
For further information for WIRED REMOTE respective destinations, be sure to check with the schematic dia- gram. 2.Viewpoint of PCB diagrams IP-BUS Capacitor Connector SIDE A SIDE B P.C.Board Chip Part DETACH SENSE DEH-P560MP/XM/UC...
Page 37
CORD ASSY SIDE A ANTENNA CN1950 FRONT CN901 DEH-P560MP/XM/UC...
D 132 Diode Network DA204U R 102 RS1/16S620J R 103 RS1/16S101J D 133 Diode DAN202U R 104 RS1/16S222J D 134 Diode DAP202U R 105 RS1/16S102J D 301 Diode S5688G D 302 Diode S5688G R 106 RS1/16S472J D 303 Diode S5688G DEH-P560MP/XM/UC...
Page 45
RS1/16S102J R 601 RS1/16S104J R 827 RS1/16S102J R 603 (P560MP) RS1/16S104J R 828 RS1/16S102J R 604 (P5650MP) RS1/16S104J R 903 RS1/16S223J R 605 RS1/16S0R0J R 912 RS1/16S222J R 606 RS1/16S104J R 913 RS1/16S223J R 607 RS1/16S822J R 914 RS1/16S104J DEH-P560MP/XM/UC...
Page 46
C 854 CKSRYB473K25 C 221 CCSRCH120J50 C 911 470µF/16V CCH1331 C 222 CCSRCH120J50 C 912 CKSRYB472K50 C 225 CEJQ100M16 C 913 CKSRYB103K50 C 241 CKSRYB152K50 C 914 CEJQ470M10 C 242 CKSRYB152K50 C 921 CEJQ221M10 C 301 CKSRYB104K16 C 922 CKSRYB103K50 DEH-P560MP/XM/UC...
Page 47
L 209 Inductor CTF1389 S 1914 Switch CSG1107 S 1915 Switch CSG1107 L 703 Inductor CTF1389 X 201 Ceramic Resonator 16.934MHzCSS1603 S 1916 Push Switch CSG1112 X 701 Ceramic Resonator 4.00MHz CSS1652 S 1917 Switch CSG1110 S 901 Switch(HOME) CSN1051 DEH-P560MP/XM/UC...
Page 48
RS1/16SS183J R 501 RS1/16SS0R0J C 101 CKSSYB104K10 R 601 RS1/16S101J C 102 CKSSYB104K10 R 602 RS1/16S101J C 103 100µF/16V CCH1504 C 104 47µF/6.3V CCH1506 R 603 RS1/16S223J C 105 CKSSYB104K10 R 604 RS1/16S223J R 605 RS1/16SS103J C 106 CCSSCH101J50 DEH-P560MP/XM/UC...
Page 49
CCH1568 C 604 4.7µF/25V CCH1568 C 701 CKSSYB104K10 C 702 CKSSYB471K50 C 703 CKSSYB103K16 C 704 4.7µF/25V CCH1592 C 706 CKSSYB104K10 C 707 CKSSYB104K10 C 712 CKSRYB224K16 C 713 CKSSYB104K10 C 714 CKSSYB104K10 C 716 CKSSYB103K16 C 720 CKSQYB225K10 DEH-P560MP/XM/UC...
1k ohms in series. • The load and eject operation is not guarantied with the mechanism upside down. If the mechanism is blocked due to mistaken eject operation, reset the product or turn off and on the ACC to restore it. DEH-P560MP/XM/UC...
Page 51
TYP(1X) TRK 22 MIN 22 SEC 22 TRK 11 MIN 11 SEC 11 As for the double speed (2x), audio output cannot be supported. → → TYP(2X) TRK 11 MIN 11 SEC 11 TRK 22 MIN 22 SEC 22 DEH-P560MP/XM/UC...
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the average angle. • Hint Reloading the disc changes the clamp position and may decrease the "wobble". DEH-P560MP/XM/UC...
Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors). Unreadable TOC does not constitute an error. An intended operation continues in this case. Upper digits of an error code are subdivided as shown below: 1x: Setup relevant errors, 3x: Search relevant errors, Ax: Other errors. DEH-P560MP/XM/UC...
The frequency of the clock signal is 312.500kHz that is one 32nd of the fundamental frequency. The clock signal should be 312.500kHz ± 13Hz. If the clock signal is out of the range, the X'tal (X601) should be replaced with new one. DEH-P560MP/XM/UC...
Grille Assy. Grille Assy Fig.1 Removing the Tuner Amp Unit (Fig.2) Remove the screw. Remove the three screws. Straighten the tabs at three locations indicated. Remove the screw and then remove the Tuner Amp Unit. Tuner Amp Unit Fig.2 DEH-P560MP/XM/UC...
Page 57
Caution: Before installing the carriage mechanism in the frames, be sure to apply some alcohol to the dampers and set the mechanism to the clamp mode. Carriage Mechanism Damper Lower Frame Damper Damper DEH-P560MP/XM/UC...
Page 58
Caution: In assembling, move the planet gear to the load/eject position before setting the feed screw in the inner holder. Washer Pickup Lock Arm Change Arm Styling Holder Feed Screw Inner Holder Planet Gear DEH-P560MP/XM/UC...
ROM correction : Data input/output EVOL : Strobe output EVOL : Data output EVOL : Clock output IPPW IPBUS : Driver power supply control output ASENBO IPBUS : Slave ACC sense output isens Illumination sense input 82,83 MODEL1,2 Model select input DEH-P560MP/XM/UC...
Page 61
TUNER : PLL communication input TUNPDO TUNER : Data output(PLL) TUNPCK TUNER : Clock output(PLL) * PD5919A IC's marked by * are MOS type. Be careful in handling them because they are very liable to be damaged by electrostatic induction. * S-80835CNUA-B8U DEH-P560MP/XM/UC...
Page 62
Remote control pulse input Dual Illumination (Green) Dual Illumination (Amber) 13–16 KD4–1 Key data input 17-22 KST6–1 Key strobe output 24-73 SEG49–0 LCD segment output 74–77 COM3–0 LCD common output VLCD LCD voltage input 79,80 V2,1 Power supply terminal *PD6294A DEH-P560MP/XM/UC...
Page 63
CD mute control output 56-58 For changer(Interruption at the edge) CD LSI chip selection output Not used xwait CD LSI write control signal output CLKOUT Internal system clock output(Open) LOCK Spindle lock input Not used xwrite CD LSI write control signal output DEH-P560MP/XM/UC...
Page 64
Flap closing sense input TYPE_A/D CD-DA analog/digital output change setup testin Chip check test program starting input HOME Home SW sense input TEMP Temperature information sense input VDSENS VD power supply short sense input Not used * PE5440A Format Meaning CMOS DEH-P560MP/XM/UC...
Page 65
Output of DRAM ras cas)(LDQM) Output of DRAM lower cas(LDQM) cas!(UDQM) Output of DRAM upper cas(UDQM) Output of DRAM we oe(cas) Output of DRAM oe(cas) D.GND Ground for digital circuits 73-88 RDB0-15 Input/output of DRAM data0-15 89-99 RA0-10 Output of DRAM address0-10 DEH-P560MP/XM/UC...
Page 66
Connected to the capacitor for output of REFOUT Reversal input of FE Output of FE ADIN Input of FE, TE A/D converter Reversal input of TE Output of TE Output of LD Input of PD D.GND Ground for digital circuits * UPD63761GJ DEH-P560MP/XM/UC...
Page 67
Input pin for preamplifier for thread OPOUT3 CH3 preamplifier output pin OPIN3(-) Input pin for inverting input for CH3 preamplifier OPIN3(+) Input pin for non-inverting input for CH3 preamplifier PREVCC PreVcc * S-L2980A15MC-C6A BA5835FM VOUT Reference voltage ON/OFF circuit * S-812C33AUA-C2N ON/OFF Reference Voltage DEH-P560MP/XM/UC...
Page 68
22 AUDIOGND audio ground Ground of audio block 23 L ch O L channel output FM stereo “L-ch” signal output or AM audio output 24 R ch O R channel output FM stereo “R-ch” signal output or AM audio output DEH-P560MP/XM/UC...
In case of the above signal, the communication with Grille microcomputer may fail. Source keys If the time interval is not 300msec, the oscillator operative may be defective. Source ON SYSPW←H Pin 1 Completes power-on operation. (After that, proceed to each source operation) DEH-P560MP/XM/UC...
7.4 CLEANING Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools: Portions to be cleaned Cleaning tools CD pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 DEH-P560MP/XM/UC...
Page 75
1. Attach the holders to both sides of the front panel. Holder CND1250(UC) CXX1645(ES) Holder CND1249(UC) CXX1644(ES) 2. Replace the front panel to the unit. 3. Flip the holders into upright positions. 4. Fix the front panel to the unit using fixing screws. Fixing screw BPZ20P060FZK(UC) CXX1646(ES) DEH-P560MP/XM/UC...
Need help?
Do you have a question about the DEH-P560MP/XM and is the answer not in the manual?
Questions and answers