HIKVISION DS-2CD2443G0-IW Series Quick Start Manual
  1. Manuals
  2. Brands
  3. HIKVISION Manuals
  4. Security Camera
  5. DS-2CD2443G0-IW Series
  6. Quick start manual

HIKVISION DS-2CD2443G0-IW Series Quick Start Manual

Network cube camera
Hide thumbs Also See for DS-2CD2443G0-IW Series:
Table of Contents

Advertisement

Quick Links

Download this manual
Network Cube Camera
( DS-2CD2443G0-IWseries )
Quick Start Guide
0

Advertisement

Table of Contents
loading

Related Manuals for HIKVISION DS-2CD2443G0-IW Series

Summary of Contents for HIKVISION DS-2CD2443G0-IW Series

  • Page 1 Network Cube Camera ( DS-2CD2443G0-IWseries ) Quick Start Guide...
  • Page 2 Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”). This user manual (hereinafter referred to be “the Manual”) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.
  • Page 3 LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS.
  • Page 4 Network Cube Camera·Quick Start Guide IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
  • Page 5 Network Cube Camera·Quick Start Guide FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
  • Page 6 Network Cube Camera·Quick Start Guide supplier or to a designated collection point. For more information see:www.recyclethis.info Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
  • Page 7 Network Cube Camera·Quick Start Guide gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité...
  • Page 8 Network Cube Camera·Quick Start Guide Warnings ● Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. ● In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information.
  • Page 9 Network Cube Camera·Quick Start Guide ● Do not touch sensor modules with fingers. If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an extended period, please replace the lens cap to protect the sensor from dirt.
  • Page 10 Network Cube Camera·Quick Start Guide ● Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer. ●...

  • Page 11: Table Of Contents

    Network Cube Camera·Quick Start Guide Table of Contents 1 Appearance Description ............... 11 1.1 Type I, II ................. 11 1.2 Type III ................14 2 Notice ................... 18 3 Installation ..................20 3.1 Memory Card Installation ..........20 3.1.1 Type I, II .............. 21 3.1.2 Type III ..............

  • Page 12: Appearance Description

    Network Cube Camera·Quick Start Guide 1 Appearance Description There are three types of appearances for 24 series camera. Please refer to the figure below. And one appearance will be taken as an example in the chapter below. Type I, II Figure 1-1 Type I Appearance Figure 1-2...
  • Page 13 Network Cube Camera·Quick Start Guide Figure 1-3 Overview...
  • Page 14 Network Cube Camera·Quick Start Guide Table 1-1 Description Description Lens Microphone IR LED Alarm: Solid red when the camera is armed; Solid blue when the camera is unarmed Status: Solid blue when the camera is Indicator added to the Hik-Connect Link: Flashing amber when network is connected;...

  • Page 15: Type Iii

    Network Cube Camera·Quick Start Guide Description O: Alarm Output Interface Power supply interface (12 VDC) Speaker Type III Figure 1-4 Type III Appearance...
  • Page 16 Network Cube Camera·Quick Start Guide Figure 1-5 Type III Overview Table 1-2 Description Description Memory Card Slot RESET/WPS...
  • Page 17 Network Cube Camera·Quick Start Guide Description 1 RJ45 10M/100M self-adaptive Ethernet port & PoE Power Interface (12 VDC) Speaker Microphone Lens ● Solid red: the camera is starting ● Solid blue: the camera is connected to the network successfully and works properly Indicator ●...
  • Page 18 Network Cube Camera·Quick Start Guide Steps: Press the WPS button on the router. Press the WPS button (about 2s) on the camera within 120s you enable the WPS of the router to join in the wireless network. Note:  The WPS button works as a reset button only when you press it when the camera is powering on.

  • Page 19: Notice

    Network Cube Camera·Quick Start Guide 2 Notice  Do not install the camera  Do not touch the lens with in the extreme whether your finger. condition.  Do not install the camera  Do not subject the camera towards the strong light or to vibration, shock or in the unstable lightening heavy pressure.
  • Page 20 Network Cube Camera·Quick Start Guide  High humidity may  Under no circumstances damage the camera should you submerge the hardware; put it in dry and camera in any type of well-ventilated place. liquid.  Electromagnetic radiation may affect the video data transmission and the image quality.

  • Page 21: Installation

    Network Cube Camera·Quick Start Guide 3 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12V DC, please make sure your power supply matches with your camera.

  • Page 22: Type I, Ii

    Network Cube Camera·Quick Start Guide 3.1.1 Type I, II Steps: 1. Insert the memory card into the card slot on the side of the camera. 2. (Optional) Push the inserted memory card to get it sprung out. Memory Card Figure 3-1 Install Memory Card 3.1.2 Type III Steps:...

  • Page 23: Type Iii

    Network Cube Camera·Quick Start Guide Slot Cover Figure 3-2 Install Memory Card Type I, II Camera Mounting 3.2.1 Stand Mounting Steps: 1. Take the bracket out from the package. Figure 3-3 Bracket...

  • Page 24: Ceiling Mounting

    Network Cube Camera·Quick Start Guide 2. Align the camera body to the bracket, and rotate the camera body to fix it with the bracket. Figure 3-4 Install the Camera Body 3. Assemble the camera as the steps above, and put the camera on the flat surface.
  • Page 25 Network Cube Camera·Quick Start Guide Drill Template Screw hole All:for Mounting Base Figure 3-5 Drill Template 2. Disassemble the 3-axis bracket. Hold the base with one hand, and rotate the pole anticlockwise to disassemble the pole from the base. Knob Pole Base Fixed...
  • Page 26 Network Cube Camera·Quick Start Guide 3. Install the fixed tray to the ceiling with the supplied screws. 4. Install the base to the fixed plate. Figure 3-7 Install the Fixed Plate and Mounting Base 5. Install the camera to the bracket. Figure 3-8 Install the Camera 6.

  • Page 27: Type Iii Camera Mounting

    Network Cube Camera·Quick Start Guide Knob 360° 90° Figure 3-9 Adjust the Camera Type III Camera Mounting This type of camera supports ceiling mounting and wall mounting. The following describes the steps for the wall or ceiling mounting. Steps: 1. Install the adapter plate to the wall or ceiling with the supplied screws.
  • Page 28 Network Cube Camera·Quick Start Guide 2. Buckle the camera base into the adapter plate. Figure 3-11 Buckle the Camera into Adapter Plate 3. Adjust surveillance angel. 1). Loosen the adjusting knob 1 to adjust the panning position and tilting position. 2).
  • Page 29 Network Cube Camera·Quick Start Guide Adjusting Knob 1 Rotation: 0° to 360° Adjusting Knob 2 Panning: 0° to 360° Tilting: 0° to 90° Figure 3-12 Adjust the Camera...

  • Page 30: Setting The Network Camera Over The Lan

    Network Cube Camera·Quick Start Guide 4 Setting the Network Camera over the Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection.

  • Page 31: Activating The Camera

    Network Cube Camera·Quick Start Guide Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We will take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation.

  • Page 32: Activation Via Sadp Software

    Network Cube Camera·Quick Start Guide Figure 4-3 Activation Interface(Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
  • Page 33 Network Cube Camera·Quick Start Guide Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera. Steps: 1. Run the SADP software to search the online devices. 2.

  • Page 34: Modifying The Ip Address

    Network Cube Camera·Quick Start Guide STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
  • Page 35 Network Cube Camera·Quick Start Guide Steps: 1. Run the SADP software. 2. Select an active device. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP. Figure 4-5 Modify the IP Address...
  • Page 36 Network Cube Camera·Quick Start Guide Note: You can enable the Hik-Connect service for the device during activation. Refer to Chapter 6.1 for detailed information. 4. Input the admin password and click Modify to activate your IP address modification. The batch IP address modification is supported by the SADP. Refer to the user manual of SADP for details.

  • Page 37: Accessing Via Web Browser

    Network Cube Camera·Quick Start Guide 5 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps:...
  • Page 38 Network Cube Camera·Quick Start Guide 4. Click Login. Figure 5-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in.

  • Page 39: Operating Via Hik-Connect App

    Network Cube Camera·Quick Start Guide 6 Operating via Hik-Connect App Purpose: Hik-Connect is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so Note: Hik-Connect service is not supported by certain camera models. Enable Hik-Connect Service on Camera Purpose: Hik-Connect service should be enabled on your camera before using...

  • Page 40: Enable Hik-Connect Service Via Web Browser

    Network Cube Camera·Quick Start Guide Figure 6-1 Verification Code Setting (SADP) Note: The verification code is required when you add the camera to Hik-Connect app. 3. Click and read "Terms of Service" and "Privacy Policy". 4. Confirm the settings. 6.1.2 Enable Hik-Connect Service via Web Browser Before you start: You need to activate the camera before enabling the service.
  • Page 41 Network Cube Camera·Quick Start Guide Steps: 1. Access the camera via web browser. Refer to Chapter 5. 2. Enter platform access configuration interface: Configuration > Network > Advanced Settings > Platform Access Figure 6-2 Platform Access Configuration (Web) 3. Select Platform Access Mode as Hik-Connect. 4.

  • Page 42: Hik-Connect Setup

    Network Cube Camera·Quick Start Guide Hik-Connect Setup Steps: 1. Download and install the Hik-Connect app by searching “Hik-Connect” in App Store or Google Play 2. Launch the app and register for a Hik-Connect user account. 3. Log in Hik-Connect app after registration. Adding Camera to Hik-Connect Before you start: You need to enable the Hik-Connect service on camera before...
  • Page 43 Network Cube Camera·Quick Start Guide You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package. Figure 6-4 Scan QR Code Note: If the QR code is missing or too blur to be recognized, you can also add the camera by tapping the icon and inputting the camera's serial number.

  • Page 44: Initializing The Memory Card

    Network Cube Camera·Quick Start Guide Initializing the Memory Card Steps: Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start recording any event triggered video in the camera such as motion detection.
  • Page 45 UD07738B...

Table of Contents