Advertisement
12 Beard guard 3/16in. (5mm)
13 Beard guard 9/32in. (7mm)
14 Eyebrow guard 1/4in. (6mm)
15 Power plug
16 Small plug
17 Hair guard 5/32in. (4mm)
18 Hair guard 3/8in. (9mm)
19 Hair guard 15/32in. (12mm)
20 Hair guard 21/32in. (16mm)
21 Fading hair guard 5/32in.-3/8in. (4-9mm)
22 Fading hair guard 5/32in.-3/8in. (4-9mm)
23 Body guard 1/8in. (3mm)
24 Body guard 3/16in. (5mm)
Not shown: cleaning brush, pouch
This symbol indicates that the
product can be rinsed under
running tap water.
2
3
4
5
6
7
1
1
2
8
9
10
1
2
11
12
13
14
15
16
17
18
20
21
23
24
26
27
Charging
2
Battery status indications
- When the battery is almost empty,
the battery status indicator lights up
orange (Fig. 2).
- When the product is charging, the
battery status indicator flashes white
slowly (Fig. 3).
- During quick charge, the battery status
indicator flashes white quickly. After
approx. 5 minutes of charging, the
battery indicator flashes white slowly.
The product now contains enough
power for one cordless trimming session.
- When the battery is fully charged, the
battery status indicator lights up white
continuously (Fig. 4).
Note: After approx. 30 minutes, the light
goes out automatically.
Charging
Charge the product before first use and
when the display indicates that the battery
is almost empty. When the product has
charged for 3 hours, it has a cordless
operating time of up to 5 hours.
- Charging, recharging or using the product
19
at temperatures below 40°F (4,5°C) or
higher than 95°F (35°C) adversely affects
the lifespan of the battery.
- If the product is subjected to a major
change in temperature, pressure or
humidity, let the product acclimatize
22
for 30 minutes before use.
1 Make sure the product is turned off.
2 Insert the small plug into the product
and put the power plug in any 120V AC
outlet (Fig. 5).
3 After charging, remove the power plug
from the wall outlet and pull the small
25
plug out of the product.
Note: An adapter plug may be necessary
for cord usage in some foreign countries.
Use an attachment plug adapter of the
proper configuration for power outlet.
Quick charge
28
After approx 5 minutes charging,
the product contains enough power
for one cordless trimming session.
Using the product
Always check the product and all accessories
before using. Do not use the product or any
accessory if it is damaged, as this may cause
injury. Always replace a damaged part with
one of the original type.
Note: This product can be used without
cord or directly from the power outlet.
Note: Switch off and clean the product
and attachments after each use.
- Use this product for its intended
household use as described in this
manual.
- For hygienic reasons, the product
should only be used by one person.
- Trimming is easier when the skin and
hair are dry.
- Be careful when trimming without a
guard as when the product is turn on it
will trim every hair it touches.
Detaching and attaching cutting elements
1 To detach a cutting element, push
upwards against the teeth of the cutting
element and take it off the handle (Fig. 6).
2 To attach a cutting element, insert
the lug of the cutting element into the
guiding slot at the front and push the
back of the cutting element onto the
product (`click`) (Fig. 7).
Detaching the precision shaver and
nose trimmer
1 Place your finger on the arrow at the
back of the attachment and push it off
the handle in the direction of the arrow
(Fig. 8).
Attaching and detaching guards
1 To attach any type of guard onto a
cutting element, slide the front part of
the guard onto the teeth of the cutting
element. Then push down the center of
the guard with your fingers or the palm
of your hand. (`click`) (Fig. 9).
2 To detach any type of guard from the
cutting element, carefully pull its back
part off the product and then slide it off
the cutting element (Fig. 10).
Note: When trimming for the first time,
start by using the guard with the maximum
trimming length setting to familiarize
yourself with the product.
Switching the product on and off
1 Press the on/off button once to turn the
product on or off (Fig. 11).
Attachments for use on beard
Full-size hair trimmer
Use the full-size hair trimmer without a
guard to trim hair close to the skin (to a
length of 1/32in./0.5mm). or to create
clean lines around your beard, neck and
sideburns.
1 To trim hair close to the skin, place the
flat side of the cutting element against
your skin and make strokes against the
direction of hair growth (Fig. 12).
2 For contouring, hold the cutting
element perpendicular to the skin and
move it upwards or downwards with
gentle pressure (Fig. 13).
Beard guards
Attach a beard guard to the full-size hair
trimmer to trim your beard and moustache
evenly. The product comes with 5 beard
guards. The hair length settings are
indicated on the guards. The settings
correspond to the remaining hair length
after trimming.
Advertisement
