Page 2
WT50B ( Ireland ) DVB-T Digital terrestrial services (MPEG2 and MPEG4-AVC(H.264)) DVB-S/S2 Receiver frequency range – 950 MHz to 2,150MHz LNB Power and Polarisation – Vertical: +13V Horizontal: +18V Current: Max. 500mA (overload protection) 22 kHz Tone – Frequency: 22kHz ± 2kHz Amplitude: 0.6V ±...
Page 3
Liquid Crystal Shutter Usage temperature range 0° - 40°C Battery Coin-shaped lithium battery CR2025 Operation time: Approx. 75 hours in continuous use of the battery made by Panasonic Viewing range Within 3.2m from front surface of the TV Materials Main body: Resin...
Page 4
Dimensions: Width: Height: Depth: Including TV stand 956mm 647mm 312mm [1,066mm 708mm 335mm] TV set only 956mm 569mm 27mm [1,066mm 630mm 27mm] Mass: Including TV stand 13.5kg [16.0kg] TV set only 11.0kg [13.0kg] Design and Specifications are subject to change without notice. Mass and dimensions shown are approximate. This equipment complies with the EMC standards listed below: EN55013, EN61000-3-2, EN61000-3-3, EN55020, EN55022, EN55024 Warning...
Safety Precautions General Guide Lines When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip"...
About lead free solder (PbF) Note: Lead is listed as (Pb) in the periodic table of elements. In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder. The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu). That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
Service Hints How to remove the backcover Remove the 1 fixing screw and WIFI DONGLE. (see Fig.5) Remove the 1 fixing screw and BT DONGLE. (see Fig.5) SCREWS (1) THEC150J /2pcs/ Fig.5 Remove the 28 fixing screws, 4 caps and the backcover. (see Fig.6) SCREWS (1) THEC150J /28pcs/ (2) TKKL55352 /4pcs/...
Chassis Board Layout P-Unit A-Board LD-Board TC-Unit on panel RM-Unit K-Board LP-Board Board Name Function A-Board AV Terminal, HDMI, AV Switch, USB, USB HUB, Digital Audio Out, Tuner DVB-T/T2/C/S/S2, SD Card, CI slot, PC, Ethernet, Wireless LAN, Bluetooth, Peaks IC, Speakers out, EEPROM, Flash Memory, DDR SDRAM P-Unit Main Input, Power Supply, Key control, Power switch LD-Board...
Models and Keys: Keys Model No. One-to-One CI PLUS DTCP-IP Widevine Netflix (for USB Rec.) TX-L42WT50B TX-L47WT50B TX-L47WT50Y TX-LR47WT50 None None USB HDD Recording: General information: Digital TV programmes can be recorded in USB HDD. A One-to-One key generated in A-board by SELF CHECK binds TV and USB-HDD for communication.
Self-check is used to automatically check the bus lines and hexadecimal code of the TV set. To enter Self-Check mode, keep pressing the down (-/v) button on the TV set and press the STATUS button on the remote control. To exit Self Check, switch off the TV set at the power button. TX-L42WT50B 42FHD Panasonic 2012LCD Self Check Complete C1B5 O.K.
Power LED blinking timing chart Subject Information of LED Flashing timing chart. Contents When abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the defective block can be identified by number of blinking of the Power LED on the front panel of the unit. Blinking Blinking timing Contents...
Service Mode Function MPU controls the functions switching for each IICs through IIC bus in this chassis. The following setting and adjustment can be adjusted by remote control in Service Menu How to enter SERVICE While pressing (-/v) button on the TV unit, press on the remote control for 3 times within 2 seconds.
SERVICE SERVICE Peaks SOFT 1.614 OPTION 1 34 Key Command ADJUST Peaks EEP 01.06.0060 OPTION 2 ee S e r v i c e 1 WB-ADJ LSI PACKAGE 0.014 OPTION 3 OPTION LSI DATA 1.01.04 OPTION 4 51 SRV-TOOL STBY SOFT 1.00.02 MODEL ID 09...
Service Tool Mode How to access Select [SRV-TOOL] in Service Mode. Press [OK] button on the remote control. SRV-TOOL Display of TD2Microcode version TD2Microcode:005a0910 Flash ROOM: AD – F1 Display of Flash ROM maker code POWER ON TIME/COUNT PTCT:00.00.00.00.00 Time 00051:30 On/Off 0000042 Display of SOS History Press [MUTE] button (3sec)
Hotel Mode 1. Purpose Restrict a function for hotels. 2. Access command to the Hotel mode setup menu. In order to display the Hotel mode setup menu, please enter the following command (within 2 second). [TV] : Vol.[Down] + [REMOTE] : AV (3 times) Then, the Hotel mode setup menu is displayed.
Data Copy by SD Card Purpose a) Board replacement (Copy the data when exchanging A-board): When exchanging A-board, the data in original A-board can be copied to SD card and then copy to new A-board. Following data can be copied. (Before exchanging) User setting data Copy to SD card...
Data Copy from TV set to SD Card Turn on the TV set. Insert SD card with a startup file (pwd file) to SD slot. On-screen Display will be appeared according to the startup file automatically. Input a following password for (a) or (b) by using remote control. (a) For Board replacement: 2770 (b) For Hotel: 4850 Data will be copied from TV set to SD card.
Data Copy from SD Card to TV set Turn on the TV set. Insert SD card with Data to SD slot. On-screen Display will be appeared according to the Data folder automatically. Input a following password for (a) or (b) by using remote control. (a) For Board replacement: 2771 (b) For Hotel: 4851 Data will be copied from SD card to TV set.
Option Bytes Description OPTION1 TEXT Ch Refresh ON (1) / OFF (0) ID-1 ON (1) / OFF (0) Macrovision Auto-judge ON (1) / OFF (0) Surround enable low bit ON (1) / OFF (0) Surround enable high bit ON (1) / OFF (0) Enable HDMI force reset ON (1) / OFF (0) TINT_Component_HDMI...
Adjustment Method Sub-Contrast/White Balance Adjustment Instrument Name Connect to Remarks Remote controller Correlation can be also taken by LCD WB meter (Minolta CA-210 or equivalent) CS-1000A or equivalent Comunication jig Computer for external control Procedure Remarks Let the panel standfor more than 3 hours at more than 20 C.
Parts Location NOTE: The numbers on the exploded view below refer to the exploded view section of the Replacement Parts List. (UK) (CONTINENTAL) 47” 47” TMK0EA153 TMK0EA153 47” 47” + 42” TMK0EA177 TEWF383 47” + 42” TMK0EG083 47” + 42” TMK0EG081 47”...
Page 30
Parts Location NOTE: The numbers on the exploded view below refer to the exploded view section of the Replacement Parts List.
Replacement Parts List Important Safety Notice Components Identified by mark have special characteristics important for safety. * When replacing any of these components, use only manufacturers specified parts. In case of ordering these spare parts, please always add the complete Model-Type number to your order. RTL (Retention Time Limited) Note: The marking (RTL) indicates that the Retention Time is Limited for this item.
Page 32
Cct Ref Parts Number Description Cct Ref Parts Number Description IC8200 C3ABUY000020 DDR SDRAM D9515 DZ2J360M0L DIODE IC8201 C3ABUY000020 DDR SDRAM D9516 DZ2J360M0L DIODE IC8202 C3ABUY000020 DDR SDRAM TRANSISTORS IC8203 C3ABUY000020 DDR SDRAM Q2001 B1ADCF000194 TRANSISTOR IC8404 C0DBZYY00382 POWER SWITCH IC Q2006 B1ABCE000015 TRANSISTOR...
Page 39
Cct Ref Parts Number Description Cct Ref Parts Number Description C8478 F1G1C104A077 S.M.CAP 100nF JK8452 K1FY104B0081 USB TERMINAL C8479 F1G1C104A077 S.M.CAP 100nF JK8600 K2LC1YYE0003 ETHERNET TERMINAL C8480 F1G1C104A077 S.M.CAP 100nF K1KA08A00506 8P CONNECTOR C8481 F1H1C105A145 S.M.CAP 1000nF K1KY20BA0394 20P CONNECTOR C8482 F1G1C104A077 S.M.CAP...
Page 40
Cct Ref Parts Number Description Cct Ref Parts Number Description TEWF392 AL TAPE (W20XL140) TQB0E2247W SLOVAKIAN TPG0EA0040 PAPER CAP TQB0E2247X BOTCUS TPD0E22351 CUSHION BOTTOM TQB0E2247Z ESTONIAN CARTON TPC0EA13001 CARTON I.C.s CENCUS TPD0E92071 CUSHION CENTER IC8902 X24CL47WT50Y PEAKS EEP TOPCUS TPD0E12201 CUSHION TOP TERMINALS AND LINKS INSTRUCTION BOOKS...
Schematic Diagrams IMPORTANT SAFETY NOTICE Components identified by mark have special characteristics important for safety. When replacing any of these components, use only manufacturers' specified parts. NOTE RESISTOR All resistors are carbon ¼W resistor, unless marked otherwise. Unit of resistance is OHM () (k=1,000, M=1,000,000) CAPACITORS All capacitors are ceramic 50V unless marked otherwise.
Page 66
LD-BOARD TNPA5615 - TOP S U F F I X . R9701 R9708 Q9508 Q9507 Q9506 R9702 R9709 R9703 R9710 L D 2 L D 1 L D 4 R9514 R9512 R9518 R9509 R9519 I C 9 5 0 0 R9517 L o w e r D9510...
Page 67
LP-BOARD TNPA5645 - TOP D2880 D2881 D2882 D2883 R2884 R2885 C2880 D2884 T N P A 56 4 5 1 L P S U F F I X . LP-BOARD TNPA5645 - BOTTOM LP10...
Page 68
K-BOARD TNPA5605 - TOP K-BOARD TNPA5605 - BOTTOM TP2802 TP2803 TP2807 D2804 R2808 R2801 D2811 D2810 D2808 R2807 C2809 R2802 C2806 C2808 C2803 D2803 R2805 T N P A 5 6 0 5 TP2801 TP2806 TP2808 TP2809 C2801 R2809 R2803 A D A B TP2800 D2806...