Related Manuals for LG 47TS50MF-B.ATC
Summary of Contents for LG 47TS50MF-B.ATC
- Page 1 OWNER’S MANUAL MONITOR SIGNAGE Please read this manual carefully before operating the your set and retain it for future reference. MONITOR SIGNAGE MODELS 47TS50MF www.lg.com...
-
Page 2: Table Of Contents
CONTENTS CONTENTS INSTALLATION PREPARATION Accessories Mounting Holes Portrait Layout Storage Method for Panel Protection - Correct Method - Incorrect Method PRODUCT INSTALLATION Installing an LVDS Cable Lighting Installation Installation in Enclosure Precaution - Correct Method - Incorrect Method TROUBLESHOOTING SPECIFICATIONS LVDS PIN MAP GUIDE NOTE The warranty will not cover any damages caused by using the product in an excessively dusty... -
Page 3: Installation Preparation
INSTALLATION PREPARATION INSTALLATION PREPARATION Accessories Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and accessories. CD (Owner's Manual)/ Easy Setup Guide NOTE... -
Page 4: Mounting Holes
INSTALLATION PREPARATION Mounting Holes Use M3 screws to mount the monitor. There are 20 positions for screws on the rear side of the product. Front of the product Rear of the product CAUTION This product has the front and back sides. Make sure the product is installed with the front side facing forward. -
Page 5: Portrait Layout
INSTALLATION PREPARATION Portrait Layout To install in portrait mode, rotate the set clockwise 90 degrees when looking at from the front. The portrait mode is only available on the scaler board. (The scaler board should support portrait mode.) CAUTION The scaler board is optional and it is not part of the product. -
Page 6: Storage Method For Panel Protection
INSTALLATION PREPARATION Storage Method for Panel Protection Correct Method Incorrect Method Panel Cushion Panel When laying the product on a flat floor, pit it face down on a cushion or blanket to prevent scratch- ing and damage. If the product is tilted onto the bezel, the bottom of the panel may be damaged. -
Page 7: Product Installation
PRODUCT INSTALLATION PRODUCT INSTALLATION Installing an LVDS Cable The LVDS cable port is located as shown in the figure below. When installing the product, make sure there is enough space to install the LVDS cable. 30 mm 45 mm 542.25 mm LVDS Cable (not included) NOTE LVDS cable is optional and not provided with the product. -
Page 8: Lighting Installation
PRODUCT INSTALLATION Lighting Installation This product must be installed with backlighting. Lighting must be installed behind the product so that the display can be seen clearly. 600 lux or more (When the Full Screen Lighting is White.) If something obstructs the backlighting, additional lighting may be required. Additional lighting 600 lux or more (When the Full Screen... -
Page 9: Installation In Enclosure
PRODUCT INSTALLATION Installation in Enclosure Install the product in the enclosure. Wear working gloves when installing the product. Do not use bare hands. Otherwise, it may cause personal injury. Place the product in the enclosure. Attach the product using the prepared screw holes and an additional enclosure guide frame. -
Page 10: Precaution
PRODUCT INSTALLATION Precaution Correct Method Incorrect Method Do not hold the screen area when holding the Do not lift up the product by holding a corner. product. CAUTION Make sure the power is disconnected before moving or installing the product. Otherwise electric shock may occur. -
Page 11: Troubleshooting
TROUBLESHOOTING TROUBLESHOOTING After-image appears on the product. Problem Resolution After-image appears when the y If you use a fixed image for a long time, the pixels may be damaged product is turned off. quickly. Use the screen-saver function. y When a dark image is displayed on the screen after an image with high contrast (black and white or gray), this may cause image sticking. -
Page 12: Specifications
SPECIFICATIONS SPECIFICATIONS Screen Size 1192.87mm diagonal Dimension (W x H x D) 1084.5 mm x 653 mm x 11.2 mm Pixel Pitch 0.5415 mm x 0.5415 mm Pixel Format 1920 horiz. by 1080 vert. Pixels, RGB stripe arrangement Color Depth 8Bit (D), 16.7 Million colors Transmittance (With POL) 6.4 % (Typ.) - Page 13 SPECIFICATIONS (Unit : mm) 1084.5 304.5 20-M3 Tap Hole 304.5 11.2...
-
Page 14: Lvds Pin Map Guide
LVDS PIN MAP GUIDE LVDS PIN MAP GUIDE LCD Connector(CN1) : FI-RE51S-HF or Equivalent, Refer to below table. Mating Connector : FI-RE51HL Cable length: 1 m of coaxial cable or less Pin No. Symbol Description Note NC or GND No Connection or Ground No Connection No Connection No Connection... - Page 15 LVDS PIN MAP GUIDE Pin No. Symbol Description Note No Connection NC or GND No Connection or Ground NC or GND No Connection or Ground Ground Ground Ground No Connection VLCD Power Supply+12.0V VLCD Power Supply+12.0V VLCD Power Supply+12.0V VLCD Power Supply+12.0V Note : 1.
- Page 16 Make sure to read the Safety Precautions before using the product. Keep the Owner's Manual (CD) in an accessible place for future reference. The model and serial number of the SET is located on the back and one side of the SET. Record it below should you ever need service.