LG 47TS50MF Owner's Manual
Hide thumbs
Also See for 47TS50MF:
- Owner's manual (16 pages) ,
- Owner's manual (17 pages) ,
- Owner's manual (16 pages)
Related Manuals for LG 47TS50MF
Summary of Contents for LG 47TS50MF
- Page 1 OWNER’S MANUAL MONITOR SIGNAGE Please read this manual carefully before operating the your set and retain it for future reference. MONITOR SIGNAGE MODELS 47TS50MF www.lg.com...
-
Page 2: Table Of Contents
CONTENTS CONTENTS INSTALLATION PREPARATION Accessories Mounting Holes Portrait Layout Storage Method for Panel Protection - Correct Method - Incorrect Method PRODUCT INSTALLATION Installing an LVDS Cable Lighting Installation Installation in Enclosure Precaution - Correct Method - Incorrect Method TROUBLESHOOTING SPECIFICATIONS LVDS PIN MAP GUIDE NOTE The warranty will not cover any damages caused by using the product in an excessively dusty environment. -
Page 3: Installation Preparation
INSTALLATION PREPARATION INSTALLATION PREPARATION Accessories Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and accessories. CD (Owner's Manual)/ Easy Setup Guide NOTE The accessories supplied with your product may vary depending on the model. Product specifications or contents in this manual may be changed without prior notice due to upgrade of product functions. LVDS cable is optional and not provided with the product. Please refer to LVDS Pin Map Guide on pages 14 to 15 for the LVDS cable assembly. CAUTION Do not use any unapproved or counterfeit parts or accessories to ensure the safety and product life span. Any damages or injuries by using unapproved items are not covered by the warranty. -
Page 4: Mounting Holes
INSTALLATION PREPARATION Mounting Holes Use M3 screws to mount the monitor. There are 20 positions for screws on the rear side of the product. Front of the product Rear of the product CAUTION This product has the front and back sides. Make sure the product is installed with the front side facing forward. Image is displayed reversely on the back side. -
Page 5: Portrait Layout
INSTALLATION PREPARATION Portrait Layout To install in portrait mode, rotate the set clockwise 90 degrees when looking at from the front. The portrait mode is only available on the scaler board. (The scaler board should support portrait mode.) CAUTION The scaler board is optional and it is not part of the product. -
Page 6: Storage Method For Panel Protection
INSTALLATION PREPARATION Storage Method for Panel Protection Correct Method Incorrect Method Panel Cushion Panel When laying the product on a flat floor, pit it face down on a cushion or blanket to prevent scratch- ing and damage. If the product is tilted onto the bezel, the bottom of the panel may be damaged. Panel Panel If there is no a cushion or a soft cloth available, ensure the floor is clean. Then lay the product down carefully with the panel facing either upward or downward. At this time, make sure that no If the product is tilted onto the edge of the panel, object falls on the panel. the panel may be damaged. -
Page 7: Product Installation
PRODUCT INSTALLATION PRODUCT INSTALLATION Installing an LVDS Cable The LVDS cable port is located as shown in the figure below. When installing the product, make sure there is enough space to install the LVDS cable. 30 mm 45 mm 542.25 mm LVDS Cable... -
Page 8: Lighting Installation
PRODUCT INSTALLATION Lighting Installation This product must be installed with backlighting. Lighting must be installed behind the product so that the display can be seen clearly. 600 lux or more (When the Full Screen Lighting is White.) If something obstructs the backlighting, additional lighting may be required. Additional lighting 600 lux or more (When the Full Screen Lighting Object is White.) Additional lighting... -
Page 9: Installation In Enclosure
PRODUCT INSTALLATION Installation in Enclosure Install the product in the enclosure. Wear working gloves when installing the product. Do not use bare hands. Otherwise, it may cause personal injury. Place the product in the enclosure. Attach the product using the prepared screw holes and an additional enclosure guide frame. Example of the product in the enclosure NOTE This product can be installed in various locations besides the enclosure. Example of the lighting installation Lighting must be installed in the enclosure. CAUTION The panel of this product is so thin that it can be easily broken when it is exposed to the outside. Use a clear protective cover to keep the product from exposure to the elements. -
Page 10: Precaution
PRODUCT INSTALLATION Precaution Correct Method Incorrect Method Do not hold the screen area when holding the Do not lift up the product by holding a corner. product. CAUTION Make sure the power is disconnected before moving or installing the product. Otherwise electric shock may occur. Wear working gloves when installing the product. Do not use bare hands. Otherwise, it may cause personal injury. If you install the product on a ceiling or Use a soft cloth moistened with n-hexane to slanted wall, it may fall and result in severe remove dust or stains on the screen. injury. Do not fasten the screws too tightly; this may cause damage to the product and void your warranty. Use M3 x 4 mm screws to mount the monitor. Any damages or injuries caused by CAUTION misuse or use of improper accessories are If a fixed image displays on the screen for a not covered by the warranty. long period of time, it will be imprinted and become a permanent disfigurement on the screen. This is image burn or burn-in and not covered by the warranty. To prevent image sticking, do not play a still image for more than two hours. Recommended operation time for optimum performance and reliability is 12 hours or less per day. -
Page 11: Troubleshooting
TROUBLESHOOTING TROUBLESHOOTING After-image appears on the product. Problem Resolution After-image appears when the y If you use a fixed image for a long time, the pixels may be damaged product is turned off. quickly. Use the screen-saver function. y When a dark image is displayed on the screen after an image with high contrast (black and white or gray), this may cause image sticking. This is normal for LCD screen. Screen color is abnormal. Problem Resolution S creen color is unstable or y Check the connection status of the LVDS cable. mono-colored. y Check whether the LVDS cable is connected correctly following the LVDS Pin Map Guide. Do black spots appear on the y S everal pixels (red, green, white or black color) may appear on the screen? screen, which can be attributable to the unique characteristics of the LCD panel. It is not a malfunction of the LCD. -
Page 12: Specifications
SPECIFICATIONS SPECIFICATIONS EEPROM EPI(RGB) Source Driver Circuit S1920 LVDS 1,2 LVDS 2Port Timing Controller Option signal LVDS Rx Intergrated TFT - LCD Panel LVDS Select (51pin) (1920 x RGB x 1080 pixels) Control [Gate In Panel] Signals +12.0V G1080 Power Circuit Block Power Signals Screen Size... - Page 13 SPECIFICATIONS (Unit : mm) 1084.5 304.5 20-M3 Tap Hole 304.5 11.2...
-
Page 14: Lvds Pin Map Guide
LVDS PIN MAP GUIDE LVDS PIN MAP GUIDE LCD Connector(CN1) : FI-RE51S-HF or Equivalent, Refer to below table. Mating Connector : FI-RE51HL Cable length: 1 m of coaxial cable or less Pin No. Symbol Description Note NC or GND No Connection or Ground No Connection No Connection No Connection No Connection No Connection LVDS Select 'H' = JEIDA, 'L' = VESA No Connection No Connection No Connection Ground R1AN FIRST LVDS Receiver Signal(A-) R1AP FIRST LVDS Receiver Signal(A+) R1BN FIRST LVDS Receiver Signal(B-) R1BP FIRST LVDS Receiver Signal(B+) R1CN FIRST LVDS Receiver Signal(C-) R1CP FIRST LVDS Receiver Signal(C+) Ground R1CLKN FIRST LVDS Receiver Clock Signal(-) R1CLKP FIRST LVDS Receiver Clock Signal(+) Ground R1DN FIRST LVDS Receiver Signal(D-) R1DP... - Page 15 LVDS PIN MAP GUIDE Pin No. Symbol Description Note No Connection NC or GND No Connection or Ground NC or GND No Connection or Ground Ground Ground Ground No Connection VLCD Power Supply+12.0V VLCD Power Supply+12.0V VLCD Power Supply+12.0V VLCD Power Supply+12.0V Note : 1. All GND (ground) pins should be connected together to the LCD module’s metal frame. 2. All VLCD (power input) pins should be connected together. 3. All Input levels of LVDS signals are based on the EIA 644 Standard. 4. #1~#6 & #8~#10 NC (No Connection) These pins are used only for LGD (Do not connect) 5. Specific pin No. #44 is used for No signal detection of system signal interface. It should be GND for NSB (No Signal Black) during the system interface signal is not. If this pin is H, LCD Module displays AGP (Auto Generation Pattern).
- Page 16 Make sure to read the Safety Precautions before using the product. Keep the Owner's Manual (CD) in an accessible place for future reference. The model and serial number of the SET is located on the back and one side of the SET. Record it below should you ever need service.