NHR S05-SM User Manual
  1. Manuals
  2. Brands
  3. NHR Manuals
  4. Accessories
  5. S05-SM
  6. User manual

NHR S05-SM User Manual

Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
S05-SM User's Manual
S05-SM User's Manual (ZigBee HA Profile)
Ver. 1.01
Copyright 2011-14 Nietzsche Enterprise Co., Ltd. All rights reserved
Nietzsche Enterprise reserves the right to make changes and improvements to its products without notice.
Contact Information: Email: service@nhr.com.tw, Website: www.nhr.com.tw
Content
1) Package Content and S05-SM Views. ............................................................................. 2
2) Installing Mounting for S05-SM ....................................................................................... 3
3) Installing and Replacing Batteries in S05-SM ................................................................ 4
4) Setting Transmission Interval for S05-SM ...................................................................... 5
5) Joining S05-SM to the Network ....................................................................................... 6
6) Removing S05-SM from the Parent's Network ............................................................. 6
7) S05-SM LED Status .............................................................................................................7
8) ZigBee Reset ...................................................................................................................... 8
9) Product Specifications .................................................................................................... 8
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the S05-SM and is the answer not in the manual?

Questions and answers

Related Manuals for NHR S05-SM

Summary of Contents for NHR S05-SM

  • Page 1 1) Package Content and S05-SM Views. …...…….………...…………………………….……………... 2 2) Installing Mounting for S05-SM .………………………………………………………………………….. 3 3) Installing and Replacing Batteries in S05-SM …..……………………………………………….. 4 4) Setting Transmission Interval for S05-SM ..….……………….………………………………….….. 5 5) Joining S05-SM to the Network ….………………………………….…………………………….……… 6 6) Removing S05-SM from the Parent’s Network ..………………………………………….……..
  • Page 2  To prevent electrical shock or fire, do not disassemble or expose the unit to liquids of any kind  Only use attachments and / or accessories specified by the manufacturer 1 Package Content and S05-SM Views Mounting fixtures (mounting cradle, 2 wall...
  • Page 3 (if not using wall plugs)  Size 1 Phillips screwdriver a) Locate S05-SM with at least 15cm (approx.. 6 inches) spacing on each side (except on mounting side) avoiding the following sources of interference: direct sunlight, air flow from vents, fans, doors, windows, heaters, sources of steam, oil vapor, etc.
  • Page 4 Recommendation: It is strongly recommended to install batteries into S05-SM just before joining to parent device as this will greatly improve battery life. For proper functioning of S05-SM and longer battery life, please install alkaline or lithium batteries from reputable suppliers.
  • Page 5 S05-SM User’s Manual 4 Setting Transmission Interval for S05-SM a) If necessary, remove the S05-SM from mounting cradle (see “Installing Mounting for S05-SM” section). b) Twist the base counter clockwise to gain internal access to the transmitter, being careful when separating the base to ensure the sensor cable connector stays connected.
  • Page 6 Enable permit join status on parent device (see relevant device’s manual) and check S05-SM joined the parent device. d) If S05-SM has successfully joined the parent device, the green LED should flash 3 times, then once every 60 seconds.
  • Page 7 Use a sharp pointed tool to apply 3 quick presses to the link switch on S05-SM, the red LED will flash rapidly for up to 30 seconds or until successful removal.
  • Page 8 In the case where the parent devices (coordinator, gateway, or router) for S05-SM are no longer available or have been reset, S05-SM will need to be reset by applying a 5-second press to the link switch, the green & red LEDs will both come on during the reset, then the green LED should show ready to join status (flash once every second).

Table of Contents