1. Manuals
  2. Brands
  3. NHR Manuals
  4. Accessories
  5. S05-TH
  6. User manual

NHR S05-TH User Manual

Digital temperature and humidity sensor zigbee ha profile
Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
S05-TH User's Manual
S05-TH User's Manual (ZigBee HA Profile)
Ver. 1.01
Copyright 2011-14 Nietzsche Enterprise Co., Ltd. All rights reserved
Nietzsche Enterprise reserves the right to make changes and improvements to its products without notice.
Contact Information: Email: service@nhr.com.tw, Website: www.nhr.com.tw
Content
1) Package Content and S05-TH Views ............................................................................. 2
2) Installing Mounting for S05-TH ...................................................................................... 3
3) Installing and Replacing Batteries in S05-TH ................................................................ 4
4) Setting Transmission Interval for S05-TH ..................................................................... 5
5) Joining S05-TH to the Network ....................................................................................... 6
6) Removing S05-TH from the Parent's Network ............................................................. 6
7) S05-TH LED Status ............................................................................................................ 7
8) ZigBee Reset ...................................................................................................................... 8
9) Product Specifications .................................................................................................... 8
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the S05-TH and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for NHR S05-TH

Summary of Contents for NHR S05-TH

  • Page 1 1) Package Content and S05-TH Views …...…….………...…………………………….……………... 2 2) Installing Mounting for S05-TH ………………………………………………………………………….. 3 3) Installing and Replacing Batteries in S05-TH …..……………………………………………….. 4 4) Setting Transmission Interval for S05-TH .….……………….………………………………….….. 5 5) Joining S05-TH to the Network ….………………………………….…………………………….……… 6 6) Removing S05-TH from the Parent’s Network ..………………………………………….……..

  • Page 2: Package Content And S05-Th Views

     To prevent electrical shock or fire, do not disassemble or expose the unit to liquids of any kind  Only use attachments and / or accessories specified by the manufacturer 1 Package Content and S05-TH Views Mounting fixtures (mounting cradle, 2 wall...

  • Page 3: Installing Mounting For S05-Th

    (if not using wall plugs)  Size 1 Phillips screwdriver a) Locate S05-TH with at least 15cm (approx.. 6 inches) spacing on each side (except on mounting side) avoiding the following sources of interference: direct sunlight, air flow from vents, fans, doors, windows, heaters, sources of steam, oil vapor, etc.

  • Page 4: Installing And Replacing Batteries In S05-Th

    Recommendation: It is strongly recommended to install batteries into S05-TH just before joining to parent device as this will greatly improve battery life. For proper functioning of S05-TH and longer battery life, please install alkaline or lithium batteries from reputable suppliers.

  • Page 5: Setting Transmission Interval For S05-Th

    S05-TH User’s Manual 4 Setting Transmission Interval for S05-TH a) If necessary, remove the S05-TH from mounting cradle (see “Installing Mounting for S05-TH” section). b) Twist the base counter clockwise to gain internal access to the transmitter, being careful when separating the base to ensure the sensor cable connector stays connected.

  • Page 6: Joining S05-Th To The Network

    Enable permit join status on parent device (see relevant device’s manual) and check S05-TH joined the parent device. d) If S05-TH has successfully joined the parent device, the green LED should flash 3 times, then once every 60 seconds.

  • Page 7: S05-Th Led Status

    Use a sharp pointed tool to apply 3 quick presses to the link switch on S05-TH, the red LED will flash rapidly for up to 30 seconds or until successful removal.

  • Page 8: Zigbee Reset

    In the case where the parent devices (coordinator, gateway, or router) for S05-TH are no longer available or have been reset, S05-TH will need to be reset by applying a 5-second press to the link switch, the green & red LEDs will both come on during the reset, then the green LED should show ready to join status (flash once every second).

Table of Contents