Related Manuals for LG 47TS30MF-B.AUS
Summary of Contents for LG 47TS30MF-B.AUS
- Page 1 OWNER’S MANUAL MONITOR SIGNAGE Please read this manual carefully before operating the your set and retain it for future reference. MONITOR SIGNAGE MODELS 26TS30MF 47TS30MF www.lg.com...
- Page 2 WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.
-
Page 3: Table Of Contents
CONTENTS CONTENTS INSTALLATION PREPARATION Accessories Mounting Holes Unpacking and Cabling Portrait Layout (Only supported for 47TS30MF) Storage Method for Panel Protection - Correct Method - Incorrect Method PRODUCT INSTALLATION Lighting installation Installation in Enclosure Precaution - Correct Method - Incorrect Method TROUBLESHOOTING SPECIFICATIONS 26TS30MF 47TS30MF LVDS PIN MAP GUIDE 26TS30MF 47TS30MF... -
Page 4: Installation Preparation
INSTALLATION PREPARATION INSTALLATION PREPARATION Accessories Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and accessories. CD (Owner's Manual)/ Easy Setup Guide CAUTION... -
Page 5: Mounting Holes
INSTALLATION PREPARATION Mounting Holes 26TS30MF Use M3 x 4 mm screws to mount the monitor. There are 16 screw holes on the rear side of the product. < Front side of the product > < Rear side of the product >... - Page 6 INSTALLATION PREPARATION 47TS30MF Use M3 x 4 mm screws to mount the monitor. There are 20 screw holes on the rear side of the product. < Front side of the product > < Rear side of the product > CAUTION This product has the front and back sides. Make sure the product is installed with the front side facing forward. Image is displayed reversely on the back side.
-
Page 7: Unpacking And Cabling
INSTALLATION PREPARATION Unpacking and Cabling 26TS30MF Lift up the cover of the box. Remove the top packaging. Hold both sides of the product and lift it up. Remove the poly bag. Place a soft cloth on the table and put the Connect the LVDS cable(Additional assembly product down with the screen facing downward. is required). A scaler board or LVDS cable is optional and not provided with the product. - Page 8 INSTALLATION PREPARATION 47TS30MF Lift up the cover of the box. Remove the top packaging. Hold both sides of the product and lift it up. Remove the poly bag. Place a soft cloth on the table and put the Connect the LVDS cable(Additional assembly product down with the screen facing downward. is required). A scaler board or LVDS cable is optional and not provided with the product. NOTE Please refer to "LVDS Pin Map Guide" on pages 16 to 18 for the LVDS cable assembly.
-
Page 9: Portrait Layout (Only Supported For 47Ts30Mf)
INSTALLATION PREPARATION Portrait Layout (Only supported for 47TS30MF) To install in portrait mode, rotate the set clockwise 90 degrees when looking at from the front. The portrait mode is only available on the scaler board.(The scaler board should support portrait mode.) CAUTION The 26TS30MF model cannot be rotated. The scaler board is optional and it is not part of the product. -
Page 10: Storage Method For Panel Protection
INSTALLATION PREPARATION Storage Method for Panel Protection Correct Method Incorrect Method Panel Cushion Panel When laying down the product, place a cushion or a soft cloth on a flat floor. Put the product down with the panel of the product facing down. If the product is tilted onto the bezel, the bottom of the panel may be damaged. Panel Panel If there is no a cushion or a soft cloth available, ensure the floor is clean. Then lay the product down carefully with the panel facing either upward or downward. At this time, make sure that no If the product is tilted onto the edge of the panel, object falls on the panel. the panel may be damaged. -
Page 11: Product Installation
PRODUCT INSTALLATION PRODUCT INSTALLATION Lighting installation This product must be installed with lighting. Lighting must be installed behind the product so that the display can be seen clearly. Lighting 600 lux or more Installing a certain object behind the screen may require additional lighting. Additional lighting Lighting 600 lux or more Object Additional lighting... -
Page 12: Installation In Enclosure
PRODUCT INSTALLATION Installation in Enclosure Install the product in the enclosure. Place the product in the enclosure. Attach the product using the prepared screw holes and an additional enclosure guide frame. < Example of the product in the enclosure > NOTE This product can be installed in various locations besides the enclosure. < Example of the lighting installation > CAUTION Lighting must be installed in the enclosure. The panel of this product is so thin that it can be easily broken when it is exposed to the outside. Please use the protective glass to prevent the product from directly being exposed to the outside. -
Page 13: Precaution
INSTALLATION PREPARATION Precaution Correct Method Incorrect Method Do not hold the screen area when holding the Do not lift up the product by holding a corner. product. CAUTION Make sure the power is disconnected before moving or installing the product.Otherwise electric shock may occur. If you install the product on a ceiling or slanted wall, it may fall and result in severe injury. Do not fasten the screws too tightly; this may Use a soft cloth moistened with n-hexane to cause damage to the product and void your remove dust or stains on the screen. warranty. Use M3 x 4 mm screws to mount the monitor. Any damages or injuries caused by misuse or use of improper accessories are not covered by the warranty. -
Page 14: Troubleshooting
TROUBLESHOOTING TROUBLESHOOTING After-image appears on the product. Problem Resolution After-image appears when the y If you use a fixed image for a long time, the pixels may be damaged product is turned off. quickly. Use the screen-saver function. Screen color is abnormal. Problem Resolution S creen color is unstable or y Check the connection status of the LVDS cable. mono-colored. y Check whether the LVDS cable is connected correctly following the "LVDS Pin Map Guide". Do black spots appear on the y S everal pixels (red, green, white or black color) may appear on the screen? screen, which can be attributable to the unique characteristics of the LCD panel. It is not a malfunction of the LCD. -
Page 15: Specifications
SPECIFICATIONS SPECIFICATIONS 26TS30MF EEPROM Source Driver Circuit S1366 LVDS Select #9 Timing Controller (30pin) [LVDS Rx] LVDS 1Port TFT - LCD Panel Control Signals (1366 x RGB x 768 pixels) [Gate In Panel] +12.0V G768 Power Circuit Block Power Signals Screen Size 26" class (25.5" / 66,4 cm diagonal) Dimension(W x H x D) -
Page 16: 47Ts30Mf
SPECIFICATIONS 47TS30MF Mini-LVDS EEPROM (RGB) Source Driver Circuit S1920 LVDS 1,2 LVDS 2Port Timing Controller Option LVDS Rx + DCA + ODC LVDS Select signal Intergrated TFT - LCD Panel (51pin) (1920 x RGB x 1080 pixels) Bit Select Control [Gate In Panel] Signals +12.0V... -
Page 17: Lvds Pin Map Guide
LVDS PIN MAP GUIDE LVDS PIN MAP GUIDE 26TS30MF LVDS Connector(CN1) : KDF71G-30S-1H(Hirose) or Compatible, Refer to below table. Mating Connector : FI-X30C2L(Manufactured by JAE) or Equivalent Cable length: 1 m of FFC cable or less Pin No. Symbol Description Note VLCD Power Supply+12.0V VLCD Power Supply+12.0V VLCD Power Supply+12.0V VLCD Power Supply+12.0V Ground Ground Ground Ground LVDS Select 'H' = JEIDA, 'L' or NC = VESA No Connection Ground LVDS Receiver Signal(-) LVDS Receiver Signal(+) Ground LVDS Receiver Signal(-) LVDS Receiver Signal(+) Ground LVDS Receiver Signal(-) LVDS Receiver Signal(+) Ground RCLK- LVDS Receiver Clock Signal(-) RCLK+ LVDS Receiver Clock Signal(+) Ground LVDS Receiver Signal(-) LVDS Receiver Signal(+) Ground... -
Page 18: 47Ts30Mf
LVDS PIN MAP GUIDE 47TS30MF LVDS Connector(CN1) : FI-RE51S-HF or Equivalent, Refer to below table. Mating Connector : FI-RE51S or Equivalent Cable length: 1 m of coaxial cable or less Pin No. Symbol Description Note Ground No Connection No Connection No Connection (Reserved for LGD) No Connection (Reserved for LGD) No Connection (Reserved for LGD) LVDS Select 'H' = JEIDA, 'L' or NC = VESA No Connection No Connection No Connection Ground RO0N FIRST LVDS Receiver Signal(A-) RO0P FIRST LVDS Receiver Signal(A+) RO1N FIRST LVDS Receiver Signal(B-) RO1P FIRST LVDS Receiver Signal(B+) RO2N FIRST LVDS Receiver Signal(C-) RO2P FIRST LVDS Receiver Signal(C+) Ground ROCLKN FIRST LVDS Receiver Clock Signal(A-) ROCLKP FIRST LVDS Receiver Clock Signal(A+) Ground RO3N FIRST LVDS Receiver Signal(D-) RO3P FIRST LVDS Receiver Signal(D+) - Page 19 LVDS PIN MAP GUIDE Pin No. Symbol Description Note No Connection No Connection No Connection Ground Ground Ground VLCD Power Supply+12.0V VLCD Power Supply+12.0V VLCD Power Supply+12.0V VLCD Power Supply+12.0V Note : 1 . All GND (Ground) pins should be connected together to the LCD module's metal frame. 2. All VLCD (power input) pins should be connected together. 3. All Input levels of LVDS signals are based on the EIA 644 Standard. 4. Specific pins(pin No. #2~#6) are used for internal data process of the LCD module. These pins should be no connections. 5. LVDS pin (pin No. #24,25,40,41) are used for 10Bit(D) of the LCD module. If used for 8Bit(R), these pins are no connection.
- Page 20 Make sure to read the Safety Precautions before using the product. Keep the Owner's Manual(CD) in an accessible place for future reference. The model and serial number of the SET is located on the back and one side of the SET. Record it below should you ever need service.
- Page 21 P/NO : 3840TRL098E (0801-REV00)