Advertisement
Quick Links
ASSEMBLY AND INSTALLATION
T0272 / T0273
WARNING:
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. Read and save these instructions.
Important to Know
1. Read all instructions carefully before installation and
operation.
2. If you are not familiar with state and local electrical codes,
it is recommended that you consult with a qualified
electrician.
3. Before installation, shut off power at the main fuse or
circuit breaker box. Be aware that simply turning off the
wall switch is not sufficient to prevent an electrical shock.
4. This fixture requires a 120V AC, 60 Hz power source.
5. Do not attempt to take the lantern apart; there are no
serviceable parts inside.
6. To avoid sensor damage by lightning or electrical surge,
make sure the grounding wire is securely connected.
7. For general safety and to avoid any possible damage to
the sensor, be sure the power is switched "off" before
replacing the bulb.
Maximum Wattage: 60W Incandescent bulb
Work Temperature: -4ºF ~ 104ºF
Fixture
Ball Nut (H)
Rubber pad (G)
Max Watt: 60W (M) - Type A
Incandescent, Halogen or
Dimmable LED
(not included)
INSTRUCTIONS
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
Back Plate
Fixture Wire
Installation Steps
Turn off the power at fuse or circuit box.
1. Thread two headless screws through the mounting plate, and then
secure them with four lock nuts (two on each side of the mounting
plate). Adjust the length of the headless screws if necessary.
Note: Make sure that the headless screws are lined up
horizontally in order to make the fixture level.
Page 1 / 4
Features
1. Energy saving fixture.
2. Use the dim-to-bright illumination option where
you want some minimum illumination through out
the night, such as at your front entrance or
garage door. Use the dark-to-bright illumination
option where you do not need minimum
brightness, such as the backyard or back porch.
3. When in manual override mode, use wall switch
to keep the light ON till dawn.
Hardware Package (included)：
Mounting
Mounting Plate (A)
Screw (B)
Wire Nut (E)
Lock Nut (F)
Wire Nut (E)
Green Grounding
Screw (C)
Ball Nut (H)
Rubber Pad (G)
Headless Screw (D)
Lock Nut (F)
Mounting Plate (A)
House Grounding Wire
Outlet Box
Green Grounding Screw (C)
Fixture Grounding Wire
160606
Advertisement
Related Manuals for Quoizel T0272
Summary of Contents for Quoizel T0272
- Page 1 ASSEMBLY AND INSTALLATION INSTRUCTIONS T0272 / T0273 WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. Read and save these instructions.
- Page 2 2. Attach the mounting plate to the outlet box by using two mounting screws. 3. Install a bulb (not included). Check relamping label at socket area or packaging for maximum allowed wattage. 4. Pull out the wires and grounding wire from the outlet box. Make wire connections using the wire nuts as follows: ---Connect the hot wire (usually black insulation) from the fixture to the black wire from the power source.
- Page 3 Fig.2 Fig.1 (View from one side of Back plate) Turn wall switch OFF-ON in 3 Seconds “3H Mode” Manual “6H Mode” Override “0 Mode” Mode Turn wall switch OFF-ON in 3 Seconds again (Adjustable low level) Fig.3 CUSTOMIZATION OPTIONS: (View from Bottom of Back plate) Shut-off Delay The Shut-off delay is the length of time the light will stay at high- level brightness after motion has ceased to be detected.
- Page 4 5576MM (1 SET) Green Grounding Mounting Mounting Plate (A) Screw (C) Screw (B) Glass Panel 9824HT FOR T0272 9825HT FOR T0273 Ball Nut (H) Rubber Pad (G) Wire Nut (E) Lock Nut (F) 5-YEAR LIMITED WARRANTY: All products are warranted to be free of defects in material and workmanship for five (5) years from date of purchase.