Related Manuals for LG M4224N-B32
Summary of Contents for LG M4224N-B32
- Page 1 OWNER’S MANUAL MONITOR SIGNAGE Please read this manual carefully before operating your set and retain it for future reference. MONITOR SIGNAGE MODELS M4224N www.lg.com...
- Page 2 Connecting the stand - Only on some models. Take the parts for the stand out of the box and assemble them as shown in the picture. First, check if the following parts are all present. Parts Screws (4) Place a soft cloth on the table and put the product with the screen facing down- ward.
- Page 3 Connecting the Speakers - Only on some models. Mount the product onto the speaker by using a screw as shown in the following connect the speaker cable. After installing your speakers, use holders and cable ties to organize the speaker cables. Cable holder Remove the paper.
-
Page 4: Name Of The Remote Control Buttons
Using the Remote Control Name of the Remote Control Buttons There is not a function which is supported There is not a function which is supported ▪ CTR.PWR Button Turn on the power of the PC built in the monitor and then turn off. -
Page 5: Inserting Batteries Into Remote Control
Using the Remote Control CTR. Inserting batteries into remote control. 1. Take out the battery cap. 2. Insert the batteries with correct polarity (+/-). 3. Close the battery cap. ▪ Dispose of used batteries in the recycle bin to prevent AAA Type ▪... -
Page 6: Rear View
Name and Function of the Parts * The product image in the user’s guide could be different from the actual image. Rear View ERIAL PORT RGB OUT RS-232C (CONTROL) Power Connector : Connect the power cord RS-232C Serial Ports (IN, OUT) RGB, DVI Ports (IN, OUT) PC Sound Jack H/PHONE... - Page 7 Connecting to External Devices When Connecting to your Built in PC When connecting with the DVI signal input Rear side of the product. Turn on power by pressing the power button on the product. Select an input signal. Press the INPUT button on the remote control to select the input signal. INPUT AUDIO (RGB/DVI)
- Page 8 Connecting to External Devices When connecting with the D-Sub signal input cable. PHONE SP/DIF SERIAL PORT RGB OUT MIC IN AUDIO (RGB/DVI) REMOTE CONTROL IN Rear side of the product. H/PHONE * User must use shielded signal interface cables (D-sub 15 pin cable, DVI cable) with fer- rite cores to maintain standard compliance for the product.
- Page 9 Connecting to External Devices Select an input signal. Press the INPUT button on the remote control to select the input signal. INPUT INPUT Or, press the SOURCE button at the back side of the product. SOURCE SOURCE When connecting with a D-Sub signal input cable. ▪...
- Page 10 Connecting to External Devices * In order to convert the RGB signal to the DVI signal Select an input signal. Press the INPUT button on the remote control to select the input signal. INPUT INPUT Or, press the SOURCE button at the back side of the product. SOURCE SOURCE When connecting with a...
-
Page 11: When Connecting To Your Pc
Connecting to External Devices When Connecting to your PC First of all, see if the computer, product and the peripherals are turned off. Then, connect the signal input cable. * User must use shielded signal interface cables (D-sub 15 pin cable, DVI cable) with ferrite cores to maintain standard compliance for the product. - Page 12 Connecting to External Devices Turn on power by pressing the power button on the product. Turn on the PC. Select an input signal. Press the INPUT button on the remote control to select the input signal. INPUT INPUT Or, press the SOURCE button at the back side of the product. SOURCE AUTO/SET SOURCE...
-
Page 13: Watching Rgb Outputs
Connecting to External Devices Watching RGB Outputs Use this function when displaying ANALOG RGB inputs of a PC to the other product. To use different products connected to each other ▪ Connect one end of the signal input cable(15-pin D-Sub Signal Cable) to the RGB OUT connector of product 1 and connect the other end to the RGB IN connector of other products. - Page 14 Selecting and Adjusting the Screen Name of the Buttons in the Screen Adjustment Unit SOURCE AUTO/SET ON/OFF SOURCE AUTO/SET SOURCE AUTO/SET Pivot model Only SOURCE SOURCE MENU MENU SOURCE MENU SOURCE AUTO/SET AUTO/SET AUTO/SET AUTO/SET...
- Page 15 Selecting and Adjusting the Screen ▪ Press this button to turn on the power. Press this button again Power Button ▪ This Indicator lights up blue when the display operates Power Indicator MENU Button ▪ Use this button to show/hide the OSD (On Screen Display) ▪...
-
Page 16: Osd Menu
Selecting and Adjusting the Screen OSD Menu Icon Adjusts screen brightness, contrast and color that you prefer. PICTURE Adjusts the audio function. SOUND Adjust the time function TIMER Adjusts the screen status according to the circumstances. SPECIAL Adjusts the screen video. SCREEN ▪... -
Page 17: How To Adjust The Screen Automatically
Selecting and Adjusting the Screen How to adjust the OSD (On Screen Display) screen Pops up Move where Select a the menu you want to menu icon screen adjust Press the MENU Button, then the main menu of the OSD appears. To access a control, use the When the icon you want becomes highlighted, press the SET Button. -
Page 18: Adjusting Screen Color
Selecting and Adjusting the Screen Adjusting Screen Color ▪ 6500K/9300K Selecting a factory setting color set. 6500K: Slightly reddish white. 9300K: Slightly bluish white. ▪ User : Select this option to use the user-defined settings. Contrast To adjust the contrast of the screen. Brightness To adjust the brightness of the screen. -
Page 19: Adjusting The Audio Function
Selecting and Adjusting the Screen Adjusting the audio function SOUND Balance SOUND Balance ▪ Flat : The most commanding and natural audio. SOUND ▪ Music : Select this option to enjoy the original sound when listening to the music. ▪ Movie : Select this option to enjoy sublime sound. Balance ▪... -
Page 20: Time Id To Adjust The Time Function
Selecting and Adjusting the Screen TIME ID to adjust the time function Clock This function is used to set up of current time. You must set the time correctly before using On/Off time function. 1) Press the MENU button and then use 2) Press the 3) Press button and then use... -
Page 21: Selecting The Options
Selecting and Adjusting the Screen Selecting the options Reset Input Reset Child lock Use the buttons to select On or Off. The Set can be set up so that it can only be used with the remote control. This feature can prevent unauthorized viewing. In order to lock the OSD screen adjustment, set the Child lock tab to the 'On' position. - Page 22 Reset Selecting and Adjusting the Screen Selecting the options To use this function Reset ▪ - You can connect the product with several other products and use the Tile mode function. Tile mode Reset ▪ Tile mode Tile mode and choose Tile alignment and set the ID of the current product to set location. Set ID ▪...
- Page 23 Selecting and Adjusting the Screen Selecting the options ▪ Tile mode - Tile mode : row x column ( r = 1, 2, 3, 4 c = 1, 2, 3, 4) - 4 x 4 available. - Configuration of an integration screen is also available as well as configuration of one by one Display. - Tile mode (product 1 ~ 4) : r(2) x c(2) - Tile mode (product 1 ~ 9) : r(3) x c(3) column...
- Page 24 Reset Selecting and Adjusting the Screen Selecting the options ▪ Tile mode (product 1 ~ 2) : r(2) x c(1) Reset Reset Use this function to reset the product to the factory default. However, language selection Reset and PC Control selection will not be initialized. Set ID Set ID PC Control...
-
Page 25: Adjusting Screen Clock/Phase And Position
Selecting and Adjusting the Screen Adjusting Screen CLOCK/PHASE and Position Auto-configure To select the image size of the screen. (1:1 menu are not supported over 1920 X 1080 resolution) Auto-configure Auto-configure Auto- This button is for the automatic adjustment of the screen position, clock and phase. This function is suitable for analog signal input only. - Page 26 Troubleshooting No image is displayed ● Is the product power cord connected? ● Is the power indicator light on? ● Power is on, power indicator is green but the screen appears extremely dark. ● Is the power indicator amber? ● Does the 'Out of range' message appear? ●...
- Page 27 Troubleshooting The screen image looks abnormal. ● Is the screen position wrong at the RGB mode? ● Do thin lines appear on the back- ground screen at the RGB mode? ● Horizontal noise appears or the char- acters look blurred at the RGB mode. ●...
- Page 28 Troubleshooting 'Child lock on' message appears. ● The 'Child lock on' message appears when pressing the Menu button. After-image appears on the product. ● After-image appears when the prod- uct is turned off. Screen color is abnormal. ● Screen has poor color resolution (16 colors).
- Page 29 Specifications The product specifications can change without prior notice for product improvement. LCD Panel 42.02 inches (106.73 cm) TFT (Thin Film Transistor) LCD (Liquid Crystal Display) Panel Anti-Glare coating Visible diagonal size: 106.73 cm 0.4845 mm x 0.4845 mm (Pixel Pitch) Power Rated Voltage Power Consumption...
- Page 30 Specifications The product specifications can change without prior notice for product improvement. Video Signal Max. Resolution Recommended Resolution RGB : 1920 X 1080 @60Hz Horizontal Frequency RGB : 30 - 83 kHz DVI : 30 - 83 kHz Vertical Frequency Synchronization Type Separate/Composite/Digital Input Connector Environmental Operational Condition Temperature: 0˚C ~ 40˚C , Humidity: 10% ~ 80% Conditions Storage Condition * Applicable only for models that support the speakers RMS Audio Output Audio Input Sensitivity...
-
Page 31: Power Indicator
Specifications PC Mode ─ Preset Mode Horizontal Preset mode Frequency (kHz) 640 x 480 31.469 800 x 600 37.879 1024 x 768 48.363 1280 x 1024 63.981 1920 x 1080 67.5 Power Indicator Mode On Mode Sleep Mode Off Mode Vertical Frequency (Hz) - Page 32 Specifications VESA wall mounting Connected to another object (stand type and wall-mounted type.) This product accepts a VESA-compliant mounting interface pad.- (This has to be purchased separately if required.) For further information, refer to the VESA Wall Mounting Instruction Guide. Kensington Security Slot- (This has to be purchased separately if required.) Connected to a locking cable that can be purchased...
-
Page 33: Connecting The Usb Cable
Connecting the USB(Universal Serial Bus) Cable "USB (Universal Serial Bus)" is an innovation in connecting your different desktop peripherals con- veniently to your computer. By using the USB, you will be able to connect your mouse, keyboard, and other peripherals to your display instead of having to connect them to your computer. This will give you greater flexibility in setting up your system. -
Page 34: Connecting The Cable
Controlling the Multiple Product RS-232C Use this method to connect several products to a single PC. You can control several products at a time by connecting them to a single PC. Connecting the cable Connect the RS-232C cable as shown in the picture. * The RS-232C protocol is used for communication between the PC and prod- uct. -
Page 35: Command Reference List
Controlling the Multiple Product RS-232C Command Reference List 01. Power 02. Main Input Select 03. Aspect Ratio 04. Screen Mute 05. Volume Mute 06. Volume Control 07. Contrast 08. Brightness 09. OSD Select 10. Remote On/Off 11. Balance 12. Select Color Temp 13. - Page 36 Controlling the Multiple Product RS-232C Protocollo trasmissione / ricezione Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] * [Command 1]: First command. (k) * [Command 2]: Second command. (a ~ u) * [Set ID]: You can adjust the set ID to choose desired product ID number in Special menu.
- Page 37 Controlling the Multiple Product RS-232C Protocollo trasmissione / ricezione 01. Power On(Command : a) ►To control Power On/Off of the Set. Transmission [k][a][ ][Set ID][ ][Data][Cr] Data 0 : Power Off 1 : Power On Acknowledgement [a][ ][Set ID][ ][OK][Data][x] ►To show the status of Power On/Off.
- Page 38 Controlling the Multiple Product RS-232C Protocollo trasmissione / ricezione 03. Aspect Ratio(Command : c) (Main picure format) ► To adjust the screen format. You can also adjust the screen format using the ARC (Aspect Ratio Control) button on remote control or in the Screen menu. Transmission [k][c][ ][Set ID][ ][Data][Cr] Data 8 : Full mode...
- Page 39 Controlling the Multiple Product RS-232C Protocollo trasmissione / ricezione 05. Volume Mute(Command : e) ► To control On/Off of the Volume Mute. Transmission [k][e][ ][Set ID][ ][Data][Cr] Data 0 : Volume Mute On (Volume Off) 1 : Volume Mute Off (Volume On) Acknowledgement [e][ ][Set ID][ ][OK][Data][x] Data 0 : Volume Mute On (Volume Off)
- Page 40 Controlling the Multiple Product RS-232C Protocollo trasmissione / ricezione 07. Contrast(Command : g) ► To adjust screen contrast. You can also adjust the contrast in the Picture menu. Transmission [k][g][ ][Set ID][ ][Data][Cr] Data Min : 00H ~ Max : 64H Refer to ‘Real data mapping’...
- Page 41 Controlling the Multiple Product RS-232C Protocollo trasmissione / ricezione 09. OSD Select(Command : l) ► To control OSD on/off to the set when RS-232C Commands are transmitted. Transmission [k][l][ ][Set ID][ ][Data][Cr] Data 0 : OSD Off 1 : OSD On Acknowledgement [l][ ][Set ID][ ][OK][Data][x] Data 0 : OSD Off...
- Page 42 Controlling the Multiple Product RS-232C Protocollo trasmissione / ricezione 12. Select Color Temp (Command : u) ► To adjust the screen color temperature. Transmission [k][u][ ][Set ID][ ][Data][Cr] Data 0 : User 1 : 9300K 2 : 6500K Acknowledgement [u][ ][Set ID][ ][OK][Data][x] Data 0 : User 1 : 9300K 2 : 6500K...
- Page 43 Controlling the Multiple Product RS-232C Protocollo trasmissione / ricezione 14. Red Gain Adjust (Command: j w) ► To adjust Red color level. Transmission [j][w][ ][Set ID][ ][Data][Cr] Data Min : 00H ~ Max : 64H Acknowledgement [w][ ][Set ID][ ][OK][Data][x] * When it is executed with the 6500K or 9300K selected, it is automatically changed to the USER.
- Page 44 Controlling the Multiple Product RS-232C Protocollo trasmissione / ricezione 17. Tiling Mode (Command :d d) ► Change a Tiling Mode.. Transmission [d][d][ ][Set ID][ ][Data][Cr] Data Description Tiling mode is off. 1 x 2 mode(column x row) 1 x 3 mode 1 x 4 mode 4 x 4 mode * The data can not be set to 0X or X0 except 00.
- Page 45 Controlling the Multiple Product RS-232C Protocollo trasmissione / ricezione 19. Tile V Position(Command : d f) ► To set the Vertical position. Transmission [d][f][][Set ID][][Data][x] * The data range is from 00 to 64(in Hex). Acknowledgement [f][][Set ID][][OK/NG][Data][x] 20. Tile H Size(Command : d g) ►...
- Page 46 Controlling the Multiple Product RS-232C Protocollo trasmissione / ricezione 22. Tile ID Set (Command : d i) ► To assign the Tile ID for Tiling function. Transmission [d][i][][Set ID][][Data][x] * The data range is from 00 to 10 tile mode. (in Hex). Acknowledgement [i][][Set ID][][OK/NG][Data][x] 23.
- Page 47 Controlling the Multiple Product RS-232C Protocollo trasmissione / ricezione 25. PC Power On/Off (Command : d s) ► To turn On and Off the built in PC. Transmission [d][s][][Set ID][][Data][x] Data 0 : PC Power Off 1 : PC Power On Acknowledgement [s][][Set ID][][OK/NG][Data][x] *This operates only when ‘PC Control’...
-
Page 48: Output Waveform
RS-232C ► Connect your wired remote control to Remote Control port on the Product. ► Output waveform single pulse, modulated with 37.917KHz signal at 455KHz ► Configuration of frame · 1st frame Lead code custom code C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 ·... - Page 49 Controlling the Multiple Product RS-232C Code(Hexa) Function ▲ ▼ VOL( ► ) VOL( ◄ ) POWER ON/OFF POWER ON POWER OFF MUTE INPUT MENU EXIT Number Key 0 Number Key 1 Number Key 2 Number Key 3 Number Key 4 Number Key 5 Number Key 6 Number Key 7...
- Page 50 EWF (Enhanced Write Filter) function Definition - Write protect function for more than one partition - This is the function to protect the partition by returning to original condition prior to the installation once rebooted after the data has been recorded or program installed How to set - Double click on the [EWF Enable] file in the [EWF] folder from the desktop and set to pro- tect after auto reboot.
- Page 51 EWF (Enhanced Write Filter) function How to cancel - Double click the [EWF Disable] file in the [EWF] folder, and the DOS Window will be dis- played to cancel the protection in 5 seconds. *Setting from DOS mode [Start] ► [Run] ► [cmd] ► [-commitanddisable -live] How to check the current EWF condition [Start] ►...
- Page 52 Windows backup and recovery using LG Smart Recovery When Backing up the current OS from Windows 1. Select [Start] ► [LG Smart Recovery] 2. Select 'System Backup' ► Designate back up location to [D:] (Do not select C: as it is where the OS is installed) ►...
- Page 53 Recovery When Restoring the current OS from Windows 1. Select 'System Restore' ► Select after checking the backup file from LG Smart Recovery 2. The system will automatically reboot and enter Recovery Mode ► System will auto- matically be restored ► 'Select 'OK' ※...
- Page 54 (When Windows cannot be booted) 1. When booting the system, press F11 on the keyboard to enter the Restore mode 2. Select 'System Restore' ► Select the backup file from LG Smart Recovery ► After checking the image to restore, click on 'OK' 3.
- Page 55 Limitation of Windows embedded XP Limitation related to the installation of Microsoft Office Embedded limitation of Microsoft Korean XP (Korean) - When you run Full Screen (Alt+Enter) from the DOS window, the font can be broken. - When saving the file with a different name from the Print window, the name of the menu window is displayed in English.
- Page 56 M a ke s u re to re a d t h e I m p o r t a n t Precautions before using the product. Keep the Owner's Manual(CD) in an accessible place for future reference. The model and serial number of the SET is located on the back and one side of the SET.