LG M4210L Owner's Manual
LG M4210L Owner's Manual

LG M4210L Owner's Manual

Monitor signage
Hide thumbs Also See for M4210L:

Advertisement

OWNER'S MANUAL
MONITOR SIGNAGE
Please read this manual carefully before operating
your set and retain it for future reference.
MONITOR SIGNAGE MODELS
M4210L
www.lg.com

Advertisement

Table of Contents
loading

Summary of Contents for LG M4210L

  • Page 1 OWNER’S MANUAL MONITOR SIGNAGE Please read this manual carefully before operating your set and retain it for future reference. MONITOR SIGNAGE MODELS M4210L www.lg.com...
  • Page 3: Table Of Contents

    Table of Contents Connecting the stand ...4 Connecting the Speakers ...5 To install Portrait ...6 Using the Remote Control ...7 Name of the Remote Control Buttons ...7 Inserting batteries into remote control..8 Name and Function of the Parts ...9 Rear View ...9 Connecting to External Devices...10 When Connecting to your PC ...10...
  • Page 4: Connecting The Stand

    Connecting the stand - Only on some models. Take the parts for the stand out of the box and assemble them as shown in the picture. Parts First, check if the following parts are all present. Screws (6) Place a soft cloth on the table and put the product with the screen facing downward.
  • Page 5: Connecting The Speakers

    Connecting the Speakers - Only on some models. Mount the product onto the speaker by using a screw as shown in the following connect the speaker cable. After installing your speakers, use holders and cable ties to organize the speaker cables. Cable holder Remove the paper.
  • Page 6: To Install Portrait

    To install Portrait - Only on some models. "When installing Portrait, rotate it clockwise based on its front."...
  • Page 7: Using The Remote Control

    Using the Remote Control Name of the Remote Control Buttons • AV Button • Sleep Button When watching AV, RGB PC,HDMI/DVI. The product will be automatically turned off after a certain period of time. Press this button repetitively to select an appropriate time duration •...
  • Page 8: Inserting Batteries Into Remote Control

    Using the Remote Control • AV Button Toggles through video RGB PC HDMI/DVI Inserting batteries into remote control. AAA Type • Input Select Button If you press the button once, the following Input Signal Window will appear. Select the signal type you want using the 1.
  • Page 9: Name And Function Of The Parts

    Name and Function of the Parts * The product image in the user's guide could be different from the actual image. Rear View Power Connector : Connect the power cord RGB PC, HDMI/DVI Ports - HDMI Supports High Definition input and HDCP (High-bandwidth Digital Content Protection). Some devices require HDCP in order to display HD signals.
  • Page 10: Connecting To External Devices

    Connecting to External Devices When Connecting to your PC First of all, see if the computer, product and the peripherals are turned off. Then, connect the signal input cable. When connecting with the D-Sub signal input cable. When connecting with the HDMI to DVI signal input cable (not included). Rear side of the product.
  • Page 11 Connecting to External Devices Turn on power by pressing the power button on the product. Turn on the PC. Select an input signal. Press the INPUT button on the remote control to select the input signal. INPUT ▼▲ Or, press the INPUT button on the back of the product. ▼▲...
  • Page 12: Vesa Fdmi Wall Mounting

    Connecting to External Devices VESA FDMI wall Mounting This product supports a VESA FDMI compliant mounting interface. These mounts are purchased separately and not available from LG. Refer to the instructions included with wall mount for more info. Kensington Security Slot The Set is equipped with a kensington Security System connector on the back panel.
  • Page 13: Video Input

    Connecting to External Devices Video Input Connect the video cable as shown in the below figure and then connect the power cord (See page 10). When connecting with a BNC cable. Connect the input terminal with a proper color match. •...
  • Page 14: Hdmi Input (480P/576P/720P/1080I/1080P)

    Connecting to External Devices HDMI Input (480p/576p/720p/1080i/1080p) - HDMI Supports High Definition input and HDCP (High-bandwidth Digital Content Protection). Some devices require HDCP in order to display HD signals. Connect the video/audio cable as shown in the below figure and then connect the power cord (See page 10).
  • Page 15: Watching Av Outputs

    Connecting to External Devices Watching AV Outputs - When using AV input, you can connect the AV Out to other monitors. BNC Cable (not included) Note • When multi-connecting in/out cascade format, no loss cables are recommended. We recommend that you should use cable distributor. Product Audio Cable (not included)
  • Page 16: User Menus

    User Menus Screen Adjustment options • Press this button to turn on the power. Press this button again to Power Button turn it off. • This Indicator lights up blue when the display operates normally(on Power Indicator mode). If the display is in sleep (Energy Saving) mode, this indicator color changes to amber.
  • Page 17 User Menus Screen Adjustment options [For PC Analog signal] AUTO/SET Button [When 1920 x 1080 is selected] INPUT INPUT Button - Toggles between inputs RGB PC HDMI/DVI IR Receiver • This is where the unit receives signals from the remote control. Auto in progress For optimal display change resolution to 1920 x 1080...
  • Page 18: Osd Menu

    OSD Menu Icon Adjusts screen brightness, contrast and color that you prefer. Picture Adjusts the audio options. Audio Adjusts the timer options. Time Adjusts the screen status according to the circumstances. Option Adjust Set ID and check Serial No. and SW version. Information Note OSD(On Screen Disp lay)
  • Page 19: How To Adjust The Osd (On Screen Display) Screen

    How to adjust the OSD (On Screen Display) screen Pops up Move where Select a the menu you want to menu icon adjust screen Press the MENU Button, then the main menu of the OSD appears. To access a control, use the When the icon you want becomes highlighted, press the SET Button.
  • Page 20: Adjusting Screen Color

    Adjusting Screen Color Picture Picture Picture Mode Mode Color Temperature Advanced Aspect Ratio Picture Reset Screen MENU Toggles between screen presets. • Vivid : Select this option to display with a sharp image. • Standard : The most general and natural screen display status. •...
  • Page 21 Adjusting Screen Color Color Picture Temperature Picture Mode Color Temperature Advanced Aspect Ratio Picture Reset Screen MENU Color Settings • Cool : Slightly purplish white. • Medium : Slightly bluish white. • Warm : Slightly reddish white. • User : Select this option to use the user-defined settings. User Green Blue...
  • Page 22 Adjusting Screen Color Advanced Picture Picture Mode Color Temperature Advanced Aspect Ratio Picture Reset Screen MENU • Gamma : Set your own gamma value. : -50/0/50 On the monitor, high gamma values display whitish images and low gamma values display high contrast images. •...
  • Page 23 Adjusting Screen Color Aspect Ratio To select the image size of the screen. Picture Picture Mode Color Temperature Advanced Aspect Ratio Picture Reset Screen MENU 16:9 Widescreen mode. Just Scan Allows you to enjoy the transmitted data fully without any images cut off. Original The aspect ratio is not adjusted from the original.
  • Page 24 Adjusting Screen Color Picture Mode Picture Reset Return factory settings. Picture Picture Mode Color Temperature Advanced Aspect Ratio Picture Reset Screen MENU Screen Adjust the screen video. Picture Picture Mode Color Temperature Advanced Aspect Ratio Picture Reset Screen MENU • Auto Config. (RGB PC input only) : This button is for the automatic adjustment of the screen •...
  • Page 25: Adjusting The Audio Function

    Adjusting the audio function Sound The best sound tone quality will be selected automatically depending on the video type that Mode you're currently watching. Audio Sound Mode Auto Volume Balance Speaker MENU • Clear Voice : By differentiating the human sound range from others,it helps users listen to human voices better.
  • Page 26: Adjusting The Timer Function

    Adjusting the timer function Time Sleep Time Auto Sleep Power On Delay Power Saving Automatic Standby MENU Sleep The power is automatically turned off when the time set by a user is passed. Time 1) Press the MENU button and then use 2) Press the button and then use Auto...
  • Page 27 Adjusting the timer function Time Sleep Time Auto Sleep Power On Delay Power Saving Automatic Standby MENU Power This screen brightness adjusting menu helps you save energy. Saving • Level: Total 4 screen brightness levels are provided. - Off: 100% light - Level 1: 80% light - Level 2: 60% light - Level 3: 40% light...
  • Page 28: Selecting The Options

    Selecting the options Option Language Key Lock ISM Method Power Indicator DPM Select Tile Mode Factory Reset Language To choose the language in which the control names are displayed. Key Lock Use the buttons to select On or Off. The monitor can be set up so that it can only be used with the remote control.
  • Page 29 Selecting the options To use this function • - Must be displayed with various other products. - Must be in a function that can be connected to RGB Cable by distributor and RS-232C. Option Tile mode Language Key Lock ISM Method Power Indicator DPM Select Tile Mode...
  • Page 30 User Menus Selecting the options - Tile mode (product 1 ~ 9) : c(3) x r(3) ID 1 ID 4 ID 7 - Tile mode (product 1 ~ 2) : c(2) x r(1) - Tile mode (product 1 ~16) : c(4) x r(4) ID 1 ID 5 ID 9...
  • Page 31 Selecting the options Tile mode Option Language Key Lock ISM Method Power Indicator DPM Select Tile Mode Factory Reset • H-Size Adjust the horizontal size of the screen taking into account the size of the bezel. • V-Size Adjust the vertical size of the screen taking into account the size of the bezel. •...
  • Page 32: Adjust Set Id And Check Serial No. And Sw Version

    Adjust Set ID and check Serial No. and SW version. Information Set ID Serial No. SW Version Set ID You can assign a unique Set ID NO (name assignment) to each product when several products are connected for display. Specify the number (01H~63H) using the and exit.
  • Page 33: Troubleshooting

    • Install the product driver, which is provided with the product, or download it from the web site. (http://www. lg.com) • See if the plug&play function is supported by referring to the video card user manual. • The Lock function prevents the OSD settings from being changed inadvertently.
  • Page 34 Troubleshooting The screen image looks abnormal. ● Is the screen position wrong? ● Do thin lines appear on the background screen? ● Horizontal noise appears or the characters look blurred. ● The screen is displayed abnormally. After-image appears on the product. ●...
  • Page 35 Troubleshooting The audio function does not work. ● No sound? ● Sound is too dull. ● Sound is too low. Screen color is abnormal. ● Screen has poor color resolution (16 colors). ● Screen color is unstable or mono-colored. ● Do black spots appear on the screen? The operation does not work normally.
  • Page 36: Specifications

    Specifications The product specifications can change without prior notice for product improvement. 106.73 cm (42.02 inch) TFT (Thin Film Transistor) LCD Panel LCD (Liquid Crystal Display) Panel Visible diagonal size: 106.73 cm 0.4845 mm (H) x 0.4845 (V) mm (Pixel Pitch) Power Rated Voltage Power Consumption...
  • Page 37 The product specifications can change without prior notice for product improvement. Video Signal Max. Resolution Recommended Resolution Horizontal Frequency Vertical Frequency Synchronization Type Input Connector Operational Condition Environmental Conditions Storage Condition * Applicable only for models that support the speakers Audio RMS Audio Output Input Sensitivity...
  • Page 38: Dtv Mode

    PC Mode - Preset Mode Horizontal Preset mode Frequency (kHz) 640 x 350 31.469 720 x 400 31.468 640 x 480 31.469 640 x 480 37.5 800 x 600 37.879 800 x 600 46.875 832 x 624 49.725 1024 x 768 48.363 1024 x 768 60.123...
  • Page 39: Communication Parameter

    Controlling the Multiple Product RS-232C Use this method to connect several products to a single PC. You can control several products at a time by connecting them to a single PC. RS-232C Configurations 7-Wire Configurations (Standard RS-232C cable) Monitor D-Sub 9 D-Sub 9 (Female) (Female)
  • Page 40: Command Reference List

    Controlling the Multiple Product RS-232C Command Reference List 01. Power 02. Input Select 03. Aspect Ratio 04. Screen Mute 05. Volume Mute 06. Volume Control 07. Contrast 08. Brightness 09. Color 10. Tint 11. Sharpness 12. OSD Select 13. Remote Lock/ key Lock 14.
  • Page 41: Controlling The Multiple Product

    Controlling the Multiple Product RS-232C 41. Power Saving 42. Power Indicator 43. H Position 44. V Position 45. H Size 46. V Size 47. Serial no. 48. S/W Version 49. Input Select COMMAND1 COMMAND2 DATA1 00H to 03H 00H to 01H 00H to 64H 00H to 64H 00H to 64H...
  • Page 42 Controlling the Multiple Product RS-232C Transmission / Receiving Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] * [Command 1]: First command. (k, j, m, d, f, x) * [Command 2]: Second command.(a to u) * [Set ID]: Set up the Set ID number of product. range : 01Hto63H.
  • Page 43 Controlling the Multiple Product RS-232C Transmission / Receiving Protocol 01. Power(Command : a) To control Power On / Off of the Set. Transmission [k][a][ ][Set ID][ ][Data][Cr] Data 0 : Power Off 1 : Power On Acknowledgement [a][ ][Set ID][ ][OK][Data][x] To show the status of Power On / Off.
  • Page 44 Controlling the Multiple Product RS-232C Transmission / Receiving Protocol 03. Aspect Ratio(Command : c) (Main picture format) To adjust the screen format. You can also adjust the screen format using the ARC (Aspect Ratio Control) button on remote control or in the Screen menu.
  • Page 45 Controlling the Multiple Product RS-232C Transmission / Receiving Protocol 05. Volume Mute(Command : e) To control On/Off of the Volume Mute. Transmission [k][e][ ][Set ID][ ][Data][Cr] Data 0 : Volume Mute On (Volume Off) 1 : Volume Mute Off (Volume On) Acknowledgement [e][ ][Set ID][ ][OK][Data][x] Data 0 : Volume Mute On (Volume Off)
  • Page 46 Controlling the Multiple Product RS-232C Transmission / Receiving Protocol 07. Contrast(Command : g) To adjust screen contrast. You can also adjust the contrast in the Picture menu. Transmission [k][g][ ][Set ID][ ][Data][Cr] Data Min : 00H to Max : 64H Refer to ‘Real data mapping’...
  • Page 47 Controlling the Multiple Product RS-232C Transmission / Receiving Protocol 09. Color(Command : i) (Video Timing only) To adjust the screen color. You can also adjust the color in the Picture menu. Transmission [k][i][ ][Set ID][ ][Data][Cr] Data Min : 00H to Max : 64H (Hexadecimal code) Refer to ‘Real data mapping’...
  • Page 48 Controlling the Multiple Product RS-232C Transmission / Receiving Protocol 11. Sharpness(Command : k) (Video Timing only) To adjust the screen Sharpness. You can also adjust the sharpness in the Picture menu. Transmission [k][k][ ][Set ID][ ][Data][Cr] Data Min : 00H to Max : 64H (Hexadecimal code) Refer to ‘Real data mapping’...
  • Page 49 Controlling the Multiple Product RS-232C Transmission / Receiving Protocol 14 Balance(Command : t) To adjust the sound balance. Transmission [k][t][ ][Set ID][ ][Data][Cr] Data Min : 00H to Max : 64H (Hexadecimal code) Refer to ‘Real data mapping’ page A 8. •...
  • Page 50 Controlling the Multiple Product RS-232C Transmission / Receiving Protocol 16. Abnormal state (Command : z) Abnormal State : Used to Read the power off status when Stand-by mode. Transmission [k][z][ ][Set ID][ ][Data][Cr] Data FF : Read 0 : Normal (Power on and signal exist) 1 : No signal (Power on) 2 : Turn the monitor off by remote control 3 : Turn the monitor off by sleep time function...
  • Page 51 Controlling the Multiple Product RS-232C Transmission / Receiving Protocol 18. Auto Configure(Command: j u) To adjust picture position and minimize image shaking automatically. it works only in RGB(PC) mode. Transmission [j][u][ ][Set ID][ ][Data][Cr] Data 1 : To set Acknowledgement [u][ ][Set ID][ ][OK][Data][x] 19.
  • Page 52 Controlling the Multiple Product RS-232C Transmission / Receiving Protocol 20. Tile Mode(Command : d d) Change a Tile Mode. Transmission [d][d][][Set ID][][Data][x] Data Description 00 or 11 Tile mode is off. 1 x 2 mode(column x row) 1 x 3 mode 1 x 4 mode 5 x 5 mode * The data can not be set to 0X or X0 except 00.
  • Page 53 Controlling the Multiple Product RS-232C Transmission / Receiving Protocol 21. Tile H Position(Command : d e) To set the Horizontal position. Transmission [d][e][][Set ID][][Data][x] Data Min : 00H to Max : 64H Refer to ‘Real data mapping’ page A 8. •...
  • Page 54 Controlling the Multiple Product RS-232C Transmission / Receiving Protocol 23. Tile H Size(Command : d g) To set the Horizontal size. Transmission [d][g][][Set ID][][Data][x] Data Min : 00H to Max : 64H Refer to ‘Real data mapping’ page A 8. •...
  • Page 55 Controlling the Multiple Product RS-232C Transmission / Receiving Protocol 25. Tile ID Set(Command : d i) To assign the Tile ID for Tiling function . Transmission [d][i][][Set ID][][Data][x] Data Min : 00H to Max : 19H (Hexadecimal code) Acknowledgement [i][][Set ID][][OK/NG][Data][x] 26 Natural Mode (In Tile mode) (Command : d j) To assign the Tile Natural mode for Tiling function .
  • Page 56 Controlling the Multiple Product RS-232C Transmission / Receiving Protocol 28. Sound Mode (Command : d y ) To adjust the Sound mode. Transmission [d][y][][Set ID][][Data][x] Data Structure Data(Hex) Mode Clear Voice Standard Music Cinema sport Game User Acknowledgement [y][][Set ID][][OK/NG][Data][x] 29.
  • Page 57 Controlling the Multiple Product RS-232C Transmission / Receiving Protocol 30. Elapsed time return(Command : d l) To read the elapsed time. Transmission [d][l][][Set ID][][Data][x] * The data is always FF(in Hex). Acknowledgement [l][][Set ID][][OK/NG][Data][x] * The data means used hours. (Hexadecimal code) 31.
  • Page 58 Controlling the Multiple Product RS-232C Transmission / Receiving Protocol 33. Auto volume (Command : d u) Automatically adjust the volume level. Transmission [d][u][][Set ID][][Data][x] Data 0 : Off 1 : On Acknowledgement [u][][Set ID][][OK/NG][Data][x] 34. Speaker (Command : d v) Turn the speaker on or off.
  • Page 59 Controlling the Multiple Product RS-232C Transmission / Receiving Protocol 35. Sleep Time (Command : f f) Set Sleep Time. Transmission [f][f][][Set ID][][Data][Cr] Data 0 : Off 1 : 10 2 : 20 3 : 30 4 : 60 5 : 90 6 : 120 7 : 180 8 : 240...
  • Page 60 Controlling the Multiple Product RS-232C Transmission / Receiving Protocol 37. Power On Delay (Command : f h) Set the schedule delay when the power is turned on (Unit: second). Transmission [f][h][][Set ID][][Data][Cr] Data : 00H to 64H (Data value) Refer to ‘Real data mapping’ page A 8. •...
  • Page 61 Controlling the Multiple Product RS-232C Transmission / Receiving Protocol 39. DPM Select (Command : f j) Set the DPM (Display Power Management) function. Transmission [f][j][][Set ID][][Data][Cr] Data 0 : Off 1: On Acknowledgement [j][][Set ID][][OK/NG][Data][x] 40. Reset (Command : f k) Execute the Picture, Screen and Factory Reset functions.
  • Page 62 Controlling the Multiple Product RS-232C Transmission / Receiving Protocol 41. Power saving(Command : f I) To set the Power saving mode. Transmission [f][I][][Set ID][][Data][Cr] Data 0 : Off 1: (static level 1) 2: (static level 2) 3: (static level 3) Acknowledgement [I][][Set ID][][OK/NG][Data][x] 42.
  • Page 63 Controlling the Multiple Product RS-232C Transmission / Receiving Protocol 44. V Position (Command : f r) To set the Horizontal position Transmission [f][r][][Set ID][][Data][Cr] * The data range is from 00 to 64(in Hex) Refer to ‘Real data mapping’ page A 8. •...
  • Page 64 Controlling the Multiple Product RS-232C Transmission / Receiving Protocol 46. V Size (Command : f t) To set the Vertical size Transmission [f][t][][Set ID][][Data][Cr] * The data range is from 00 to 64(in Hex) Refer to ‘Real data mapping’ page A 8. •...
  • Page 65 Controlling the Multiple Product RS-232C Transmission / Receiving Protocol 48. S/W Version (Command : f z) Check the software version. Transmission [f][z][][Set ID][][Data][Cr] Data FFH : Read Acknowledgement [z][][Set ID][][OK/NG][Data][x] 49. Input Select (Command : x b) To select input source for the Set. Transmission [x][b][ ][Set ID][ ][Data][Cr] Data 20H : AV...
  • Page 66 Controlling the Multiple Product RS-232C RS-232C Connect your wired remote control to Remote Control port on the Product. Output waveform single pulse, modulated with 37.917kHz signal at 455kHz Configuration of frame • 1st frame Lead code custom code C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 •...
  • Page 67 Controlling the Multiple Product RS-232C RS-232C Code(Hex) Function VOL( VOL( POWER ON/OFF POWER ON POWER OFF MUTE INPUT SLEEP MENU EXIT Number Key 0 Number Key 1 Number Key 2 Number Key 3 Number Key 4 Number Key 5 Number Key 6 Number Key 7 Number Key 8 Number Key 9...
  • Page 68 LICENSES Supported licenses may differ by model. For more information of the licenses, visit www. lg.com. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
  • Page 69 Make sure to read the Safety Precautions before using the product. Keep the Owner's Manual(CD) in an accessible place for future reference. The model and serial number of the SET is located on the back and one side of the SET.

This manual is also suitable for:

M4210lcba

Table of Contents