Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Hyundai H-SA6041
Summary of Contents for Hyundai H-SA6041
- Page 1 H-SA6041 4-WAY CAR AMPLIFIER Instruction manual HYUNDAI H-SA6041...
- Page 2 · Do not run wiring underneath or outside the car since exposure to the elements may cause the insulation to deteriorate rapidly, resulting in short-circuits and/or intermittent operation. All cables should be run beneath carpets and inside trim pieces. · To help minimize interference, it is best to run the power cables along the opposite side from the audio cables. HYUNDAI H-SA6041...
-
Page 3: Installation
3. Remove amplifier. Drill four 3.5 mm. Diameter holes into mounting surface on steel panel. If you want mounting the MDF or wood panel, drill four 3.0m/m diameter holes into mounting surface. 4. If possible, test the system operating before final mounting of the amplifier. 5. Mount the amplifier using the supplied 4 self threading screws. HYUNDAI H-SA6041... -
Page 4: Installation Diagram
· Connect the low level/line level RCA cables from the head unit, or signal processor, to the line level input on the amplifier. See Fig.3 system wiring diagrams. HIGH INPUT CONNECTIONS Connect the HIGH LEVEL INPUT connector wires to the speaker level of the unit as in the diagram. Use #18 or thicker stranded, insulated hookup wire. Fig.2. HYUNDAI H-SA6041... -
Page 5: Power Connections
Positive-Connect the proper size wire to the amplifier "B+" terminal of amplifier. Run wire to wards the fuse holder that is no greater then 0.5 meters from the battery. Remember, the fuse is to protect the safety of the car in the case of a short. Connect fuse holder to battery, however, do not install fuse at this time. Fig.3. HYUNDAI H-SA6041... -
Page 6: Speaker Connections
Reversing any of these connections will result in the speaker cones moving out of phase which causes bass cancellation. See Fig.4 Speaker Output Connections. Fig.4. HYUNDAI H-SA6041... - Page 7 5.The "BASS" function can be selected to increase low frequency response output, or decrease frequency response output. The "BASS" function will be working at only "OFF" or "L.P.F" position. The BASS is adjustable from 0/+6/+12dB boost at 50Hz. Fig.5. HYUNDAI H-SA6041...
-
Page 8: Troubleshooting Guide
Check all grounds, check battery voltage, check RCA cables Ticking noise on audio Check RCA audio cable; Install an in-line noise filter on the head Amplifier is peaking up radiated spark noise with engine running unit s power wire, check spark plug wires HYUNDAI H-SA6041... -
Page 9: Low Pass Filter
SPECIFICATION MODEL H-SA6041 4 OHMS @ 0.5% 0Hz - 30kHz) THD (2 60 W 4 OUTPUT OF BRIDGED(BTL) 2 OHMS @ 0.5% THD 120 W 4 OPERATION INTO 4 OHMS @ 1KHz, 1% THD 500 W 1 (VARIABLE) LOW PASS FILTER... - Page 10 · «A » MOSFET PWM. · · · · 0/+6/+12 · RCA, · · · · · · · · · · · · 5,27 · HYUNDAI H-SA6041...
- Page 11 · · · · · · · « ». · 0,832 · +12 . · · · · · · .1). HYUNDAI H-SA6041...
- Page 12 · · ) RCA .2). · (HIGH LEVEL INPUT) 0,832 . 2. HYUNDAI H-SA6041...
- Page 13 · · · «GND» · · · · · «REMOTE» «remote amplifier» · « +» HYUNDAI H-SA6041...
- Page 14 · 4 - 8 · · .4). HYUNDAI H-SA6041...
- Page 15 · « .F», · «L. .F», · «OFF». · «MIN» (3 ). ¾ « » (200 , ¾ · «BASS» 0/+6/+12 «L.P.F» «OFF»). HYUNDAI H-SA6041...
- Page 16 · , RCA HYUNDAI H-SA6041...
- Page 17 H-SA6041 @ 0,5% .(20 @ 0,5% ) @ 1 ; 1% WTD) >100 272 59 280 HYUNDAI H-SA6041...