Whirlpool WDF590SAJW User Manual page 5

Delay displays how many hours before the cycle will begin.
To delay the start
1. Select a wash cycle and options.
2. Press the delay button. Each time you press DELAY, it will
display the next available delay time.
3. Press START to begin the delay countdown.
NOTE: If the door is opened, such as to add a dish, the Start button must be pressed to resume the delay countdown.
Sanitizes dishes and glassware in accordance with NSF
International NSF/ANSI Standard 184 for Residential
Dishwashers. Certified residential dishwashers are not
intended for licensed food establishments. Only sanitizing
cycles have been designed to meet the requirements of the
NSF/ANSI 184 performance standard for soil removal and
sanitization efficacy. There is no intention, either directly or
indirectly, that all cycles on a NSF/ANSI 184 certified
dishwasher meet the NSF/ANSI 184 performance standard
for soil removal and sanitization efficacy.
Sani Rinse indicator is lit at the end of the cycle if the Sani
Rinse option was successfully completed. If indicator does
not light, it is probably due to the cycle being interrupted.
Raises water temperature to improve cleaning for loads
containing tough, baked-on food.
Turns the heating element on at the end of the wash portion
of the cycle. Its shorter heating time uses significantly less
energy compared to using Heat Dry.
Dries dishes with heat. This option, with the use of rinse aid,
will provide the best drying results. Plastic items are less
likely to deform when loaded in the top rack. Use Heat Dry
for optimum drying performance or turn the Heat Dry option
off for air dry.
Control Lock Use the Control Lock option to avoid unintended use of dishwasher between cycles, or cycle and option changes during a cycle.
To turn on Control Lock, press and hold SANI RINSE for 3 seconds. Control Lock light will stay on for a short time, indicating that it
is activated. When the Lock indicator is lit, all buttons are disabled. If you press any button while your dishwasher is locked, the light
flashes 3 times. The dishwasher door can still be opened/closed while the controls are locked.
To turn off Control Lock, press and hold SANI RINSE for 3 seconds. Control Lock light turns off.
Control
OPTIONS
Purpose Comments
Press to start or If the door is opened during a cycle or the power is interrupted, the Start/Resume button LED
resume a wash flashes. Cycle will not resume until START/RESUME is pressed and door is closed.
cycle.
Press to cancel Close the door firmly. Press and hold START/RESUME for 3 seconds. The dishwasher starts a
wash cycle. 2-minute drain (if needed). Let dishwasher drain completely.
To follow progress The Complete indicator glows when a cycle is finished.
of your dishwasher
If you select the Sani Rinse option, when the cycle is finished, the Sanitized indicator glows. If
cycle.
your dishwasher did not properly sanitize your dishes, the light flashes at the end of the cycle.
This can happen if the cycle is interrupted or if water could not be heated to required
temperature. The light goes off when you open and close door or press CANCEL.
CAN BE WHAT IT DOES ADDED TIME
SELECTED
WITH
Available with Delays start of a
any cycle
cycle up to
24 hours
Sensor Raises the main
Heavy
wash temperature
Normal
to 135°F (57°C)
and the final rinse
temperature to
156°F (69°C).
Sensor Raises the main
Heavy
wash temperature
Normal
to 135°F (57°C).
Available with
any cycle
Sensor Uses a heating
Heavy
element to speed
Normal
drying times. Heat
1-Hour Wash
Dry option
defaults to On
when any cycle is
selected except
for 1-Hour Wash
and Light.
5
TO CYCLE
GALLONS*
.
0:05 to 1:06
(0 to 14.6)
0:05 to 0:13
(0 to 14.6)
0:11
0:08 to 0:46
ADDED
WATER
(LITERS)
0 to 3.9
0 to 3.9
0
0