Advertisement
1
Connect
Start with the 'Basic Connection.'
If you have a VCR, follow the instructions for 'Connection with a VCR or similar device'.
Basic Connection
Television (rear)
To antenna
or set-top
R
box
To AC
6
power
COAXIAL
P
B
S-VIDEO (Y/C)
(DIGITAL AUDIO)
OUT 3
AUDIO
Philips recorder
(rear)
VIDEO (CVBS)
P
R
COMPONENT
Y
UT
VIDEO
UT 1
L
UT 2
R
COAXIAL
S-VIDEO (Y/C)
P
B
(DIGITAL AUDIO)
AUDIO
OUT 3
A
Before connecting, unplug the antenna cable that
is currently connected to your TV.
B
Connect the antenna cable to the ANTENNA-
IN
jack on the recorder.
C
Use the supplied RF coaxial cable to connect the
TV-OUT
jack on this recorder to the
Antenna In jack on the TV.
D
Use the supplied audio/video cable (yellow plug)
to connect the VIDEO (CVBS) -OUT1 jack
on this recorder to the VIDEO IN jack on the
TV.
E
Use the supplied audio/video cable (red/ white
plugs) to connect the AUDIO OUTPUT jacks
on this recorder to the AUDIO IN jacks on the
TV.
F
Connect the power cable from the recorder to
an AC power outlet.
Connection with a VCR or
similar device
A
Before Connecting
Your new Philips recorder replaces the VCR for your
recording needs. First, unplug all the connections
from your VCR.
B
Connecting
Television (rear)
R
To antenna or
set-top box
To AC
power
COAXIAL
P
B
S-VIDEO (Y/C)
(DIGITAL AUDIO)
OUT 3
AUDIO
To AC
Philips recorder
power
(rear)
VIDEO IN
(CVBS)
L
AUDIO OUT
R
VCR or similar
device (rear)
A
A
E
Follow steps
to
of 'Connecting' under
'Basic Connections' to connect the recorder
before you proceed to step
B
below.
B
Use a yellow video cable (not supplied) to
connect the VIDEO (CVBS) EXT 1 jack on
this recorder to the yellow VIDEO OUT jack on
the VCR.
C
Use another red and white audio cable (not
supplied) to connect the AUDIO INPUT jacks
on this recorder to the red and white AUDIO
OUT jacks on the VCR.
D
Connect the power cable from your VCR to an
AC power outlet.
E
Connect the power cable from the recorder to
an AC power outlet.
Note In this setup, the VCR cannot record TV programs.
For additional connection diagrams, see the
accompanying User Manual.
A
Finding the viewing channel
STANDBY-ON
Philips recorder (front panel)
A
Press STANDBY-ON on the recorder.
B
Switch on the TV set.
Note If connected to your VCR, make sure it
is switched off or in standby mode before
proceeding.
C
Press "0" and then the Channel Down
button on the TV's remote control repeatedly
(or
AV, SELECT, ° button) until you see this screen.
This is the correct viewing channel for the
recorder.
Set up
2
B
Initial Installation
A
Press SYSTEM MENU
on the remote
control.
System Menu - General
Screen Saver
On
Progressuve/ Interlaced
Interlaced
Video Output Format
PAL
Restore Factory Settings
OK
Note Use up
or down
keys to toggle through
the options. Select an item by pressing right
. To
confi rm a setting, press OK
.
B
Select the OSD language.
Highlight
and press right
.
Select { On-Screen Display Language } and
press right
to access the options. Press
OK
to confirm your selection.
C
Setup and install TV channels.
Highlight
and press right
.
Select { Channel Search } and press OK
on the remote control to start automatic TV
channel search.
D
Setting the date and time.
Highlight
and press right
.
Select { Date (dd/mm/yy) } or { Time
(hh/mm/ss) } and press OK
.
Use the numeric keypad 0
-9
to
input the date/time, then press OK
to
confi rm.
Note The settings will be updated according to the
broadcast channel information of preset Programme
Number 1.
E
Press SYSTEM MENU
to exit.
Advertisement
