Gpv3000.1D Pro D Class 1 Channel Amplifier Applications - Crunch Ground Pounder GPV1000.2 User Manual

GPV3000.1D PRO D CLASS 1 CHANNEL AMPLIFIER APPLICATIONS

Basic application
SINGLE AMP INSTALLATION PROCEDURE:
1. Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out
puts with good quality RCA interconnect cables.
2. Plug in the GPR-1 bass remote module into the amp REMOTE INPUT jack.
3. Route a 0 gauge power cables directly to the vehicle battery with an in-line fuse.
4. Connect a 0 gauge ground cables directly to chassis ground with in 36" of the amp.
- Be sure to remove any paint or primer from the ground point.
- Use a nut, bolt and lock washer to secure the ground cable to the chassis ground.
5. Connect the subwoofer(s) in accordance to the diagrams below.
6. Make sure the MASTER/SLAVE switch is in the MASTER position.
Note: The amplifier will not work if the MASTER/SLAVE switch is in the Slave position
DESIGNATED
MONO OUTPUT
FROM HEAD UNIT
MIN MAXX
GPR-1
DUAL AMP INSTALLATION PROCEDURE:
1. Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out
puts with good quality RCA interconnect cables.
2. Plug in the GPR-1 bass remote module into the amp REMOTE INPUT jack. This will
allow the Master amp to control both Master and Slave amps with just one Remote..
3. Connect an RCA jumper cable from the Master amp MASTER OUTPUT to the
Slave amp SLAVE INPUT. Note: This will "link" the amps so that the Master amp
crossover switches will control both the Master and Slave amps. The Slave amp
crossover switches will be bypassed.
4. Route two 0 gauge power cables directly to the vehicle battery with an in-line fuse.
DESIGNATED
MONO OUTPUT
FROM HEAD UNIT
MIN MAXX
GPR-1
SINGLE REMOTE,
CONNECTED TO MASTER
AMP, USED TO CONTROL
BOTH AMPS WHEN LINKED
8
30th ANNIVERSARY
GROUND POUNDER
Linking two amps for single or dual subwoofer application
MASTER
30th ANNIVERSARY
OUTPUT
MASTER
INPUT
SLAVE
GROUND POUNDER
SLAVE
30th ANNIVERSARY
OUTPUT
MASTER
INPUT
SLAVE
GROUND POUNDER
FULL RANGE
STEREO LINE INPUT
NOT USED
Note: You can use the Radio/CD designated mono line output
or a full range stereo line output. For full range stereo line
output, you will need an optional "Y-Adaptor" as shown.
MONO
SUBWOOFER
REMOTE TURN-ON
CHASSIS GROUND
TO BATTERY + 12 Volts
VIA FUSE
5. Connect two 0 gauge ground cables directly to the chassis with in 36" of the amp.
- Be sure to remove any paint or primer from the ground point.
- Use a nut, bolt and lock washer to secure the ground cable to the chassis ground.
6. Make sure the Master amp MASTER/SLAVE switch is in the MASTER position.
Make sure the Slave amp MASTER/SLAVE switch is in the SLAVE position.
7. Connect the subwoofer(s) in accordance to the diagrams below.
8. Connect a 12 gauge jumper from Master amp speaker - to Slave amp speaker - as
shown below.
POWER SPEAKER
+12V GND -
REM
Amplifiers are stable to 2ohms when linked
SUBWOOFER
POWER SPEAKER
-
+12V GND REM
- +
Y-ADAPTOR
PARALLEL MONO
SUBWOOFERS
2 OHMS EACH MINIMUM
POWER SPEAKER
- -
+12V GND + +
REM
POWER SPEAKER
- +12V GND - -
+ + REM
DUAL VOICE COIL
SUBWOOFER /
AMPLIFIERS NOT
LINKED
POWER SPEAKER
- - -
+ + +12V GND REM
TWO SUBWOOFERS /
TWO AMPLIFIERS
- +
NOT LINKED
+ +
+ +