NEC MultiSync X464UNV-3 User Manual page 27

TILE MATRIX Allows one image to be expanded and displayed over multiple screens (up to 100) through a
distribution amplifi er.
NOTE: Low resolution is not suitable for tiling to a large number of monitors. You can operate
without a distribution amplifi er at a lower number of screens.
This function is released when selecting IMAGE FLIP except for NONE.
NOTE: Dynamic or Zoom will not work when Tile Matrix is activated.
When "DYNAMIC" or "ZOOM" is selected in ASPECT while executing TILE MATRIX, the setting
will be applied after completing of TILE MATRIX.
H MONITORS Number of monitors arranged horizontally.
V MONITORS Number of monitors arranged vertically.
POSITION Select which section of the tiled image to be displayed on the monitor.
TILE COMP Turns the TILE COMP feature on.
TILE MATRIX ENABLE Enables Tile Matrix.
FRAME COMP Sets the tiled image timing to be displayed on the monitor. Large number makes large infl uence
to displayed image.
NOTE: The image may be distorted when turning the power on or changing the settings.
NONE FRAME COMP is not available.
AUTO Sets display timing to vertical direction of all monitors automatically.
MANUAL Sets display timing to individual monitor.
1
V SCAN REVERSE* Reverse scanning image direction. Normal scanning direction is top to bottom.
NOTE: If V SCAN REVERSE is set to AUTO or MANUAL, FRAME COMP is not available.
NONE V SCAN REVERSE is not available.
AUTO Sets automatically calculated image scanning direction to all monitors.
MANUAL Sets scanning direction to individual monitor.
NON REVERSE Sets normal scanning direction and delays 1 frame display image timing.
REVERSE Reverse scanning direction to individual monitor.
TILE MATRIX MEM When "INPUT" is selected, TILE MATRIX setting is applied to each signal input.
AUTO TILE MATRIX Allows auto setting of multiple screens by inputting the number of monitors arranged horizontally
SETUP and vertically on the primary monitor. Following settings are set automatically: MONITOR
ID, TILE MATRIX, TILE MATRIX MEM, Input Signal, VIDEO OUT SETTING, DisplayPort in
TERMINAL SETTING.
NOTE: All monitors which follow in the chain with LAN should be ON. When executing this
function while in standby mode or power save mode, "LAN POWER" should be set to ON.
AUTO ID will be automatically executed. When you use this function, it is recommended that
monitors are chained by DisplayPort cable.
POWER ON DELAY Adjusts the delay time between being in "standby" mode and entering "power on" mode.
DELAY TIME "POWER ON DELAY" can be set between 0 and 50 seconds.
LINK TO ID When "ON" selected, delay time is linked with Monitor ID. It takes more time as larger ID number.
VIDEO OUT SETTING Enables the signal output from DPORT. See also page 28 "DisplayPort" in TERMINAL SETTING.
NOTE: When VGA or Y/Pb/Pr is selected as the main picture, nothing will be output from DPORT.
When this function is ON, DPORT cannot be selected as the sub picture. When this function is
ON, INPUT CHANGE is limited to be NORMAL or QUICK. When this function is ON and DPORT
is selected as the main picture, PIP CHANGE button of remote control (see page 11) is disabled.
Input signal
Connector Connector
*1: Main picture in PIP (Picture in Picture) mode. *1:
*2: When you use HDMI OUT connector in SB3-DB1, multicple monitors connection is available. *2:
POWER INDICATOR Turns ON or OFF the LED located at the back of the monitor.
If "OFF" is selected, LED will not light when the LCD monitor is in active mode.
*1: Except for X554UNV-2.
Example of installation via LAN:
H MONITORS 3
V MONITORS 3
DPORT DPORT DVI DVI HDMI HDMI VGA VGA Y/Pb/Pr Y/Pb/Pr OPTION
name* 1
DisplayPort DisplayPort DVI-D DVI-D HDMI HDMI D-Sub D-Sub
DP OUT DP OUT Yes Yes Yes Yes Yes Yes — —
Main picture in PIP (Picture in Picture) mode.
When you use HDMI OUT connector in SB3-DB1, multicple monitors connection is available.
When you use DPOUT for HDCP authentication signal, Input signal name should be DPORT. When you use DPOUT for HDCP authentication signal, Input signal name should be DPORT.
Multiple monitors that are daisy-chained have a limit to the connectable monitors. Multiple monitors that are daisy-chained have a limit to the connectable monitors.
Primary monitor
OPTION VIDEO VIDEO S-VIDEO S-VIDEO SCART SCART Y/Pb/Pr2 Y/Pb/Pr2
SLOT2 SLOT2 SLOT3 SLOT3
— —
Yes Yes — — —
(SB3-AB1) (SB3-AB1)
English-25
COMMON
DEACTIVATE
RGB/HV HDMI2 RGB/HV HDMI2 HDMI3 HDMI3
Yes Yes
Yes Yes —* 2 —* 2
(SB3-AB2) (SB3-AB2)
1
1
1
NO
NO
NONE
NONE
0 SEC.
OFF
ON
ON