Kenwood KDC-BT460U Instruction Manual page 82

Audioeinstellungen
Einstellpunkte für 2-Wege-Übergang
[SPEAKER SIZE]
[FRONT] [SIZE]
[TWEETER]
[REAR] [8CM]/[10CM]/[12CM]/[13CM]/[16CM]/[17CM]/[18CM]/[4×6]/
[5×7]/[6×8]/[6×9]/[7×10]/[NONE] (nicht angeschlossen)
[SUBWOOFER]
[16CM]/[20CM]/[25CM]/[30CM]/[38CM OVER]/[NONE] (nicht
angeschlossen)
[X ' OVER]
[TWEETER] [FRQ]
[GAIN LEFT]
[GAIN RIGHT]
[FRONT HPF] [F-HPF FRQ]
[F-HPF SLOPE]
[F-HPF GAIN]
[REAR HPF] [R-HPF FRQ]
[R-HPF SLOPE]
[R-HPF GAIN]
18
DEUTSCH
[8CM]/[10CM]/[12CM]/[13CM]/[16CM]/[17CM]/
[18CM]/[4×6]/[5×7]/[6×8]/[6×9]/[7×10]
[SMALL]/[MIDDLE]/[LARGE]/[NONE] (nicht
angeschlossen)
[1KHZ]/[1.6KHZ]/[2.5KHZ]/[4KHZ]/[5KHZ]/[6.3KHZ]/
[8KHZ]/[10KHZ]/[12.5KHZ]
[–8] bis [0]
[–8] bis [0]
[30HZ]/[40HZ]/[50HZ]/[60HZ]/[70HZ]/[80HZ]/
[90HZ]/[100HZ]/[120HZ]/[150HZ]/[180HZ]/[220HZ]/
[250HZ]/[THROUGH]
[–6DB]/[–12DB]/[–18DB]/[–24DB]
[–8] bis [0]
Konfigurieren Sie die Einstellungen für die hinteren
Lautsprecher ähnlich wie für die vorderen Lautsprecher.
[SUBWOOFER LPF] [SW LPF FRQ]
[SW LPF SLOPE]
[SW LPF PHASE]
[SW LPF GAIN]
• [SUBWOOFER] von [SPEAKER SIZE] und [SUBWOOFER LPF] von [X'OVER] ist nur wählbar,
wenn [SWITCH PREOUT] auf [SUB-W] (Seite 5) und [SUBWOOFER SET] auf [ON]
gestellt ist. (Seite 16)
Einstellpunkte für 3-Wege-Übergang
[SPEAKER SIZE]
[TWEETER] [SMALL]/[MIDDLE]/[LARGE]
[MID RANGE] [8CM]/[10CM]/[12CM]/[13CM]/[16CM]/[17CM]/[18CM]/[4×6]/[5×7]/
[6×8]/[6×9]
[WOOFER] [16CM]/[20CM]/[25CM]/[30CM]/[38CM OVER]/[NONE] (nicht
angeschlossen)
[X ' OVER]
[TWEETER] [HPF FRQ]
[SLOPE]
[PHASE]
[GAIN]
[30HZ]/[40HZ]/[50HZ]/[60HZ]/[70HZ]/[80HZ]/
[90HZ]/[100HZ]/[120HZ]/[150HZ]/[180HZ]/[220HZ]/
[250HZ]/[THROUGH]
[–6DB]/[–12DB]/[–18DB]/[–24DB]
[REVERSE] (180°)/[NORMAL] (0°)
[–8] bis [0]
[1KHZ]/[1.6KHZ]/[2.5KHZ]/[4KHZ]/[5KHZ]/[6.3KHZ]/
[8KHZ]/[10KHZ]/[12.5KHZ]
[–6DB]/[–12DB]
[REVERSE] (180°)/[NORMAL] (0°)
[–8] bis [0]