Advertisement
DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty item replaced by a qualified electrician.
8
1.3.
BATTERY SAFETY PRECAUTIONS
WARNING! Battery contains Lithium-ion which is dangerous. Handle with care to avoid damage, fire, corrosion or personal injury.
‰
Charge battery prior to its first use. The battery will have been shipped in a low charge state. To reduce the risk of burns or fire:
9
DO NOT Attempt to open, disassemble, modify or service the battery pack.
8
DO NOT Crush, puncture, short external contacts or dispose of in fire or water.
8
DO NOT Expose to temperatures above 40°C (104°F).
8
Replace only with the battery pack designated for this product.
9
Use only the supplied charging base provided to charge the battery.
9
DO NOT attempt recharging the battery by means of an engine generator or a DC power source.
8
WARNING! Dispose of spent batteries correctly as they contain Lithium-ion. DANGER! DO NOT attempt to disassemble the
‰
battery. For safety and environmental reasons DO NOT discard in domestic waste or by burning. ONLY discard or recycle
according to local authority regulations.
WARNING! DO NOT allow a leaking battery to contact your person.
‰
1.4.
GENERAL SAFETY.
Maintain the Ratchet Wrench and battery in good condition. Check moving parts alignment on a regular basis.
9
Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be
9
dangerous and will invalidate the warranty.
Ensure the Ratchet Wrench is switched off before installing the battery pack.
9
Keep the Ratchet Wrench and charger clean for best and safest performance.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Evaluate your working area before using the Ratchet Wrench; e.g. ceilings, floors and enclosures may contain electrical items or
9
water piping
Ensure battery pack is correctly inserted into the Ratchet Wrench handle and latched in place before attempting to switch on
9
Ratchet Wrench.
Secure loose work pieces with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting.
9
Wear approved safety eye protection (standard spectacles are not adequate).
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-skid shoes.
9
Be aware that this Ratchet Wrench does not need to be plugged into the mains power.
9
Keep children and unauthorised persons away from the working area.
9
DO NOT use the Ratchet Wrench where there are flammable liquids, solids or gases, such as paint solvents, etc.
8
DO NOT allow children to operate the Ratchet Wrench.
8
DO NOT operate the Ratchet Wrench if any parts are missing as this may cause failure and/or personal injury.
8
DO NOT hold unsecured work piece in your hand.
8
DO NOT leave the Ratchet Wrench operating unattended.
8
DO NOT carry the Ratchet Wrench with your finger on the power switch. Keep chuck direction switch in the locked position.
8
DO NOT use the Ratchet Wrench for a task it is not designed to perform.
8
DO NOT operate the Ratchet Wrench when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT get the Ratchet Wrench or battery charger wet or use in damp or wet locations.
8
2. INTRODUCTION
Compact, lightweight cordless ratchet wrench allows access to tight spaces. With spindle locking that gives more control during application and
a quick stopping function. Steel ratchet head with forward and reverse control. Robust housing with soft, comfortable grip. Supplied with 1 hour
mains charger and 1 x 2Ah rechargeable Lithium-ion battery.
3. SPECIFICATION
Model No.. ....................................................... CP108VCRW
Battery ................................................ 10.8V 2Ah Lithium-ion
Consumable parts .............................CP108VBP 2Ah Battery
Drive ........................................................................... 3/8"sq.
Max. torque ...................................................... 45Nm(33lb.ft)
Noise power/noise pressure ................................. 91/80dB(A)
No-load speed .........................................................0-300rpm
Replacement parts .....................CP108VMC - mains charger
Vibration/uncertainty ..................................11.64m/s²/1.5m/s²
4. BATTERY CHARGING
4.1.
Fully charge the battery before first use.
WARNING! Only recharge batteries with the charger supplied.
‰
4.2.
Remove battery by squeezing buttons in on each side. Insert into battery charger.
4.3.
Connect charger to mains supply and red LED will light to signal charging. Once charging is complete LED turns green.
4.4.
Remove from mains supply, remove battery and insert into tool until a click is heard.
4.5.
BATTERY CHARGE STATUS TEST
4.5.1.
Press trigger, all LEDs lit: battery charged, one LED lit: battery needs charging.
4.6.
In order to maintain battery efficiency:
DO NOT fully discharge. After every use fully charge the battery, charge every 4 months even if tool is not used.
If a decrease of performance of the tool is noticed, charge the battery.
5. OPERATION
5.1.
USING THE WRENCH
5.1.1.
Fit the socket to the wrench by snapping it onto the square drive.
© Jack Sealey Limited
Original Language Version
CP108VCRW Issue 1 22/02/21
Advertisement
