Sealey SV12 Series Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instruction
protection
manual
1. SAFETY
1.1. GENERAL SAFETY
Disconnect the battery from the tool before changing accessories, servicing or performing any maintenance.
9
Maintain tool and accessories in good condition. Check moving parts and alignment. If necessary use an authorised service agent.
9
Replace or repair damaged parts using recommended parts. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Wear approved safety eye protection with side shields and a dust mask if generating dust.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Use the tool in a suitable work area. Keep area clean and tidy and free from unrelated materials and ensure that there is adequate lighting.
9
Maintain correct balance and footing.
9
Keep children and unauthorised persons away from the work area.
9
Secure unstable work piece with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting. Keep the tool clean for best and safest performance.
9
When not in use switch tool off. Store it in the case and put in a dry, childproof area.
9
DO NOT over-reach. Ensure the floor is not slippery and wear non-slip shoes.
8
DO NOT use the tool for a task it is not designed to perform.
8
DO NOT operate tool where there are flammable liquids or gases.
8
DO NOT get the tool wet or use in damp or wet locations.
8
DO NOT hold unsecured work in your hand.
8
DO NOT leave the tool running unattended.
8
DO NOT operate the tool if any parts are missing or damaged as this may cause failure and/or personal injury.
8
DO NOT operate the tool when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
1.2. HAND ARM VIBRATION
WARNING! – Risk of Hand Arm Vibration Injury.
‰
This tool may cause Hand Arm Vibration Syndrome if its use is not managed adequately.
This tool is subject to the vibration testing section of the Machinery Directive 2006/42/EC.
This tool is to be operated in accordance with these instructions.
Measured vibration emission value (a): 1.024m/s²
Uncertainty value (k): 1.5 m/s²
Please note that the application of the tool to a sole specialist task may produce a different average vibration emission. We recommend
that a specific evaluation of the vibration emission is conducted prior to commencing with a specialist task.
A health and safety assessment by the user or employer will need to be carried out to determine the suitable duration of use for each tool.
NB: Stated Vibration Emission values are type-test values and are intended to be typical.
Whilst in use, the actual value will vary considerably from and depend on many factors, such as the operator, the task and the inserted
tool or consumable.
NB: ensure that the length of leader hoses is sufficient to allow unrestricted use, as this also helps to reduce vibration.
The state of maintenance of the tool itself is also an important factor, a poorly maintained tool will also increase the risk of Hand Arm
Vibration Syndrome.
1.3. HEALTH SURVEILLANCE
We recommend a programme of health surveillance to detect early symptoms of vibration injury so that management procedures can be
modified accordingly.
1.4. PERSONAL PROTECTIVE EQUIPMENT
We are not aware of any personal protective equipment (PPE) that provides protection against vibration injury that may result from the
uncontrolled use of this tool. We recommend a sufficient supply of clothing (including gloves) to enable the operator to remain warm and
dry and maintain good blood circulation in fingers etc. Please note that the most effective protection is prevention, please refer to the
Correct Use and Maintenance section in these instructions. Guidance relating to the management of hand arm vibration can be found on
the HSC website www.hse.gov.uk - Hand-Arm Vibration at Work.
© Jack Sealey Limited
12V SV12 SERIES 49PC CORDLESS MULTIPURPOSE
ROTARY TOOL & ENGRAVER KIT - BODY ONLY
MODEL NO:
Wear protective Wear a mask
gloves
Original Language Version
CP1207
CP1207 Issue 3 (ALL) 13/06/23