Advertisement
Quick Links
NSDCN65S OPERATION MANUAL
NSDCN65S/SP Technical Data
Length
Width
Height
Weight
Operating Pressure
PACKING LIST:
NSDCN7515 COIL NAILER
S5 HEX KEY
S4 HEX KEY
S3 HEX KEY
AIR TOOL OIL
SAFETY GLASSES
BUMP OR SEQUENTIAL
FIRE TRIGGER
12-1/4"
5"
12-1/2"
6.4lbs
70-120psi
QTY
1
1
1
1
1
1
1
NAIL DIMENSIONS:
15° Round Head Coil nails
Length: 1-3/4" – 2.5"
Shank diameter: .090"– .113"
Head: .224" – .276"
Instruction Manual Contents:
◎ Important Safety Rules
◎ Operating Instructions
◎ Maintenance
◎ Troubleshooting
◎ Parts List
◎ Composite Fencing Installation
Advertisement
Related Manuals for UFO NSDCN65S
Summary of Contents for UFO NSDCN65S
- Page 1 NSDCN65S OPERATION MANUAL NSDCN65S/SP Technical Data NAIL DIMENSIONS: Length 12-1/4" 15° Round Head Coil nails Length: 1-3/4” – 2.5” Width 5" Shank diameter: .090”– .113” Height 12-1/2" Head: .224” – .276” Weight 6.4lbs Operating Pressure 70-120psi PACKING LIST: Instruction Manual Contents: ◎...
- Page 2 Lower the pressure as a last resort and as little as necessary to get the job done. The NSDCN65S/SP should be sequentially fired into steel. First, place the nose of the tool where you want the fastener to be; this will depress the safety. Second, use the trigger to fire the tool in this sequence each and every time.
-
Page 3: Important Safety Rules
IMPORTANT! Upon receipt of your NailScrew® Driver, Read and follow all safety rules and operating instructions. Important Safety Rules 1. KEEP CHILDREN AWAY. All children should be kept away from the work area. Do not allow them to handle the tool. Fig 1. -
Page 4: Power Source
POWER SOURCE This tool is designed to operate on clean, dry, compressed air at regulated pressures between 70 and 120 PSI (4.9 and 8.3 bar) (Pounds per Square Inch). The preferred system would include a filter. CAUTION: All line components (hoses, connectors, filters, regulators, etc.) must meet 150% of the maximum system pressure. - Page 5 Close the Nail Housing door and depress the Latch 6. Adjust directional EXHAUST deflector so that the exhaust air blast will be directed away from the operator. Grasp the deflector and rotate it to the desired position for the current application. RUBBER NO-MAR TIP: ADJUSTING THE DRIVE DEPTH: Driving depth will be adjusted by rolling the...
-
Page 6: Maintenance
Service advice: 1. Use clean, dry and regulated compressed air, 8 cfm at 5.0-7.5 bar (70-120psi) and 100-120psi at the tool. 2. Never exceed the maximum and minimum pressures. Too low or too high pressure will cause noise, increased wear or misfiring. 3. -
Page 7: Troubleshooting
※ Troubleshooting Following are common operating problems and solutions. Please read carefully for suggested solutions. WARNING: If any of the following symptoms occur during tool operation, stop using the tool immediately or serious personal injury could result! Only a qualified person or an authorized service center can perform repairs or replacement of tool parts. - Page 8 NSDCN65S Part Part Item Number Description Item Number Description 820641 SHCS BOLT 920548 FEED BUMPER 820408 WASHER 920549 FEED PISTON CAP 820320 DEFLECTOR 920585 C - RING 810643 MUFFLER 810331 FEEDER PAW 820041 RUBBER WASHER 810333 FEEDER SPRING 820163 920553...
- Page 9 NSDCN65S For Parts & Service Contact: http://elder-hayesinc.com or call 1-800-769-0775...