1. Manuals
  2. Brands
  3. UFO Manuals
  4. Nail Gun
  5. NSDCN75
  6. Operation manual

UFO NSDCN75 Operation Manual

Hide thumbs
1
2
3
4
5
6
7
8
9
Table of Contents

Advertisement

Quick Links

Download this manual
OPERATION MANUAL
NSDCN75 Technical Data
Length
12-1/4"
Width
5"
Height
12-1/2"
Weight 6.4lbs
Operating Pressure
70-120psi
NAIL DIMENSIONS:
15° Round Head Coil nails
Length: 1-3/4" – 3"
Shank diameter: .086"– .131"
Head: .224" – .276"
1

Advertisement

Table of Contents
loading

Related Manuals for UFO NSDCN75

Summary of Contents for UFO NSDCN75

  • Page 1 OPERATION MANUAL NSDCN75 Technical Data NAIL DIMENSIONS: Length 12-1/4" 15° Round Head Coil nails Length: 1-3/4” – 3” Width 5" Shank diameter: .086”– .131” Height 12-1/2" Head: .224” – .276” Weight 6.4lbs Operating Pressure 70-120psi...
  • Page 2 Lower the pressure as a last resort and as little as necessary to get the job done. • The NSDCN75 should be sequentially fired into steel. First, place the nose of the tool where you want the fastener to be; this will depress the safety. Second, use the trigger to fire the tool in this sequence each and every time.

  • Page 3: Important Safety Rules

    IMPORTANT! Upon receipt of your NailScrew® Driver, Read and follow all safety rules and operating instructions. Important Safety Rules KEEP CHILDREN AWAY. All children should be kept away from the work area. Do not allow them to handle the tool. Fig 1.

  • Page 4: Power Source

    POWER SOURCE This tool is designed to operate on clean, dry, compressed air at regulated pressures between 70 and 120 PSI (4.9 and 8.3 bar) (Pounds per Square Inch). The preferred system would include a filter. CAUTION: All line components (hoses, connectors, filters, regulators, etc.) must meet 150% of the maximum system pressure.

  • Page 5: Clearing A Jammed Fastener

    Close the Nail Housing door and depress the Latch 6. Adjust directional EXHAUST deflector so that the exhaust air blast will be directed away from the operator. Grasp the deflector and rotate it to the desired position for the current application. RUBBER NO-MAR TIP: ADJUSTING THE DRIVE DEPTH: Driving depth will be adjusted by rolling the...

  • Page 6: Maintenance

    Service advice: 1. Use clean, dry and regulated compressed air, 8 cfm at 5.0-7.5 bar (70-120psi) and 100-120psi at the tool. 2. Never exceed the maximum and minimum pressures. Too low or too high pressure will cause noise, increased wear or misfiring. 3.

  • Page 7: Troubleshooting

    Troubleshooting Following are common operating problems and solutions. Please read carefully for suggested solutions.  WARNING If any of the following symptoms occur during tool operation, stop using the tool immediately or serious personal injury could result! Only a qualified person or an authorized service center can perform repairs or replacement of tool parts.
  • Page 8 NSDCN75 PARTS LIST ITEM PART# DESCRIPTION ITEM PART # DESCRIPTION DEFLECTOR BLOT(3M2353) 830223 O - RING 810108 920615 O - RING 820128 FEED PISTON DEFLECTOR 830234 O - RING 810109 920502 HEX.SOC.HD.SCREW PUSHER SPRING 810124 820676 HEX.SOC.HD.BOLT 810125 PUSHER SPRING...
  • Page 9 NSDCN75 For Parts & Service Contact: http://elder-hayesinc.com or call 1-800-769-0775...

Table of Contents