Table of Contents
Advertisement
Quick Links
Serial No _____________________________
Note - Your 2 Year Warranty can only be valid once your warranty card is completed and returned to Selectronic Australia
S
ELECTRONIC
A
USTRALIA
.
Purchase Date ______________
LD350-12 Volt Owners Manual
Contents
Demand Start Setting
Low Voltage Shutdown Setting
Legend for Symbols
Warnings and
Hints and Pointers
electrician's notes
Page No.
1
1
1
4
6
6
7
7
9
10
11
11
11
12
13
14
15
16
Back Cover
Examples
Advertisement
Table of Contents
Related Manuals for Selectronic Australia LD350-12
Summary of Contents for Selectronic Australia LD350-12
-
Page 1: Table Of Contents
Back Cover Legend for Symbols Serial No _____________________________ Purchase Date ______________ Note - Your 2 Year Warranty can only be valid once your warranty card is completed and returned to Selectronic Australia Warnings and Examples Hints and Pointers electrician’s notes... -
Page 2: Introduction
Thank you for choosing to purchase the Selectronic LD350-12 TRUE SINE WAVE inverter. Many hours of Research and Development have Fixed Installation gone into the LD350-12 to ensure this inverter provides you with many All fixed installation battery connections must be securely bolted, years of reliable service using stainless steel nuts and bolts. -
Page 3: Batteries And Connections
(see your auto electrician). capacity of 12 Volts – 150 Ah. The LD350-12 has sufficient battery cable length to allow it to sit underneath the vehicle whilst in use. If the ground is wet, place the LD350-12 on a waterproof liner. LD350-12 Manual... -
Page 4: Getting Started Quickly
4. Make sure the LD350-12 ON/OFF switch (12) is in the off position. 5. Connect battery positive wire (red) (10) to battery positive or battery fuse. 6. Connect battery neg. wire (black) (11) to battery negative or battery fuse. -
Page 5: Operation
LED (5) tells you what LED (1) – (4) is displaying as indicated on the front ON. The LD350-12 will remain in this condition for 1 minute after the AC panel of the LD350-12. Pressing Mode Button (7) will change the information load has been decreased to a safe level. - Page 6 It is sometimes necessary to adjust the demand start sensitivity to overcome To avoid total discharging of your battery the LD350-12 shuts down at a pre- what is called “Phantom Loads”. A phantom load is a load that tricks the set low voltage.
-
Page 7: Maintenance
3. Once a fortnight or as directed in your battery manufacturer, check the specific gravity (SG) of each battery cell using a hydrometer, to ensure Periodic maintenance of your LD350-12 inverter involves little more than that all cells are performing correctly and are properly charged. Any... -
Page 8: Radio Frequency Interference
See page 2 for (as described in Handy Hint, check to see if the LD350-12 returns to pulsing wiring details. -
Page 9: Product Warranty Conditions
Inverter Type Microprocessor control circuit with PWM full bridge power stage. True sine wave AC output Warranty Current draw from Battery Selectronic Australia Pty Ltd warrants your inverter to be free from Condition Amperage defects in materials and workmanship under normal use and service, Demand Start SLEEP mode (average) 0.06 Amps... - Page 10 Operating Temperature Range 0º C to 40º C Transformer Type Toroidal Cooling Method Controlled fan-forced Power Point 10 Amp Single Pole Chassis Material Zinc Coated Steel Chassis Coating Powder Coated Size 230W x 130H x 260mm D LD350-12 Manual Selectronic Australia...
-
Page 11: Selectronic Service Network
Selectronic Authorised Service Network Selectronic Australia 25 Holloway Drive Bayswater Victoria 3153 Australia Ph: 03 9762 4822 Fax: 03 9762 9646 service@selectronic.com.au Burley TV Service Rainbow Power Company 278 Edmondson Ave. 1 Alternative Way Austral Nimbin 2171 NSW 2480 Australia...
Need help?
Do you have a question about the LD350-12 and is the answer not in the manual?
Questions and answers