Table of Contents
Advertisement
Input Source
ATV, AV, Component (480i, 480p)
DTV (1080i, 1080p), Component (1080i,
1080p), HDMI (720p, 1080i, 1080p)
■ Digital Noise Filter (Off / Low / Medium / High / Auto) : If the
■
broadcast signal received by your TV is weak, you can activate
the Digital Noise Filter feature to reduce any static and ghosting
that may appear on the screen.
✎
When the signal is weak, try all the Digital Noise Filter
options until the TV displays the best picture.
■ HDMI Black Level (Normal / Low) : For HDMI signals, select
■
the black level to adjust the screen depth. Low make blacks look
darker.
✎
Available only in HDMI mode (RGB signals).
■ Film Mode (Off / Auto) : Sets the TV to automatically sense and
■
process film signals from all sources and adjusts the picture for
optimum quality.
✎
Available in ATV, DTV (interlace), AV, COMPONENT (480i /
1080i) and HDMI (480i / 1080i).
■ Screen Burn Protection : To reduce the possibility of screen
■
burn, this unit is equipped with Pixel Shift screen burn prevention
technology. Pixel Shift moves the picture slightly on the screen.
The Time function setting allows you to program the time
between movement of the picture in minutes.
x
Pixel Shift (Off / On) : Using this function, you can set the TV
to move pixels minutely on the PDP screen in a horizontal or
vertical direction to minimize after images on the screen.
Available Pixel Shift Settings and Optimum Settings
Available Settings
Horizontal
0~4 (pixels)
Vertical
0~4 (pixels)
Time
1~4 min
(minute)
✎
The Pixel Shift value may differ depending on the
monitor size (inches) and mode.
✎
This function is not available in the Screen Fit mode.
Your TV also has the following additional screen burn
protection functions:
x
Scrolling: This function removes after-images on the screen
by illuminating all the pixels on the PDP according to a pattern.
Use this function when there are after images or symbols on
the screen, especially when you displayed a still image on the
screen for a long time.
✎
The after-image removal function has
(approximately 1 hour) to remove after-images on the
screen effectively. If the after-image is not removed after
you run the function, run the function again.
✎
Press any key on the remote control to cancel this
feature.
x
Side Gray (Dark/Light): Lets you select the color of the
sidebars your TV displays when you set the screen size to 4:3.
■ Picture Reset (Reset Picture Mode/Cancel): Resets the
■
picture settings to their factory defaults.
Picture Size
16:9, Zoom1,
Zoom2, 4:3
16:9, Wide Fit,
4:3, Screen Fit
Optimum Settings
4
4
4 min
to run a long time
- 3 -
Sound Menu
Mode t
■ Standard: Selects the normal sound mode.
■
■ Music: Emphasizes music over voices.
■
■ Movie: Provides the best sound for movies.
■
■ Clear Voice: Emphasizes voices over other sounds.
■
■ Amplify: Increase the intensity of high-frequency sounds to allow
■
a better listening experience for the hearing impaired.
Equalizer
Available in Standard sound mode only.
■ Balance L/R: Adjusts the balance between the right and left
■
speaker.
■ 100Hz / 300Hz / 1KHz / 3KHz / 10KHz (Bandwidth
■
Adjustment): Adjusts the loudness of specific bandwidth
frequencies.
■ Reset: Resets the equalizer to its default settings.
■
SRS TruSurround HD (On/Off)
Available in Standard sound mode only.
SRS TruSurround HD is a patented SRS technology that solves
the problem of playing 5.1 multichannel content through two
speakers. TruSurround delivers a compelling, virtual surround
sound experience through any two-speaker playback system,
including internal television speakers. It is fully compatible with all
multichannel formats.
Preferred Language
Digital channels only.
Digital-TV broadcasts can transmit many audio tracks
simultaneously (for example, simultaneous translations of a program
into foreign languages).
✎
You can only select a language from among the ones being
broadcast.
Multi-Track Sound (MTS)
Analog channels only.
■ Mono: Select for channels that are broadcasting in mono or if
■
you are having difficulty receiving a stereo signal.
■ Stereo: Select for channels that are broadcasting in stereo.
■
■ SAP: Select to listen to the Separate Audio Program, which is
■
usually a foreign-language translation.
✎
Depending on the program being broadcast, you can listen to
Mono, Stereo or SAP.
Auto Volume
Because each station has its own broadcasting conditions, the
volume may fluctuate each time you change the channel. This
feature automatically adjusts the volume of a channel by lowering
the sound output when the modulation signal is high or by raising
the sound output when the modulation signal is low.
SPDIF Output
The SPDIF (Sony Philips Digital InterFace) outputs an
uncompressed digital audio signal when you connect the digital
audio jack on the back of the TV to a digital audio in jack on a
receiver or home theater.
■ Audio Format (PCM/Dolby Digital): You can select the Digital
■
Audio output (SPDIF) format. The available Digital Audio output
format may differ depending on the input source.
Hide quick links:
Advertisement
Table of Contents
