Samsung SyncMaster 320TSn-3 User Manual

Hide thumbs Also See for SyncMaster 320TSn-3:
Table of Contents

Advertisement

Quick Links

SyncMaster 320TSn-3

LCD Display

User Manual

The color and the appearance may differ depending on the
product, and the specifications are subject to change
without prior notice to improve the performance.

Advertisement

Table of Contents
loading

Summary of Contents for Samsung SyncMaster 320TSn-3

  • Page 1: Lcd Display

    SyncMaster 320TSn-3 LCD Display User Manual The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance.
  • Page 2: Safety Instructions

    Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property dam- age. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.
  • Page 3: Installation

    Ensure that the power plug is plugged into the power outlet firmly and correctly. • Do not forcefully bend or pull the power plug and do not place any heavy material on it. • Do not connect multiple appliances to the same power outlet. •...
  • Page 4 DO NOT PLACE CANDLES, MOSQUITO REPELLANT, CIG- ARETTES AND ANY HEATING APPLIANCES NEAR THE PRODUCT. • Otherwise, this may result in fire. Keep heating appliances as far away from the power cord or the product as possible. • Otherwise, this may result in electric shock or fire. Do not install it in a badly ventilated location such as a bookcase or closet.
  • Page 5 Clean When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft cloth. Do not spray cleaner directly onto the surface of the product. • When cleaning the power plug pins or dusting the power outlet, clean it with a dry cloth.
  • Page 6 Do not place this product in a location exposed to moisture, dust, smoke, water, or in a car. • Otherwise, this may result in electric shock or fire. When you drop the product or the case is broken, turn the power off and disconnect the power cord.
  • Page 7 Set a resolution and frequency appropriate to the product. • Otherwise, your eyesight may be damaged. When using headphones or earphones, do not turn the volume too high. • Having the sound too loud may damage your hearing. To avoid eyestrain, do not sit too close to the product. Take a rest for at least five (5) minutes after using the monitor for one (1) hour.
  • Page 8 When replacing the battery, insert it with the right polarity (+, -). • Otherwise, the battery may become damaged or it may cause fire, personal injury or damage due to leakage of the internal liquid. Use only the specified standardized batteries, and do not use a new battery and a used battery at the same time.
  • Page 9 Do not install the product in a location low enough for children to reach. • Otherwise, it may fall and result in personal injury. • Since the front part of the product is heavy, install the product on a level and stable surface. Do not put any heavy objects on the product.
  • Page 10 Introduction Package Contents Checking the Contents of the Package Note • After unpacking the package, make sure to check the contents of the package. • Store the packaging box in case you need to move the Product later. • If any items are missing, contact your dealer. •...
  • Page 11 Cables Power Cord Others Remote Control Batteries (AAA X 2) (BP59-00138B) (Not available in all loca- Sold separately Semi Stand KIT RGB to BNC Cable RGB to COMPONENT Ca- Wall Mount KIT Note Accessories that can be purchased with the product vary by country. D-Sub Cable tions) LAN Cable...
  • Page 12: Your Lcd Display

    Your LCD Display The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. Front MENU button [MENU] Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu.
  • Page 13 A TV tuner box (sold separately) must be connected to use the TV. Using MagicInfo To use MagicInfo with an TSn-3 model, install inside the product a network box specified by Samsung and connect the MagicInfo output on the net- work box to [HDMI IN 2 (MAGICINFO)] on the product. D.MENU button Opens the on-screen D.MENU.
  • Page 14 │ ] / OFF POWER S/W ON [ Switches the LCD Display On/Off. POWER The power cord plugs into the LCD Display and the wall outlet. RGB/COMPONENT IN (PC/COMPO- NENT Connection Terminal (Input)) • Connect the [RGB/COMPONENT IN] port on the monitor to the RGB port on the PC using the D-SUB cable.
  • Page 15 Receives a signal from the Display port. Connect a DP cable to [DP IN] on the product and DP IN on another display. AV/COMPONENT AUDIO IN [R-AUDIO- Connect the [AV/COMPONENT AUDIO IN [R-AUDIO-L]] port on the monitor to the audio output port on the PC or on the external de- vice using an audio cable.
  • Page 16 Using MagicInfo To use MagicInfo with an TSn-3 model, in- stall inside the product a network box speci- fied by Samsung and connect the MagicIn- fo output on the network box to [HDMI IN 2 (MAGICINFO)] on the product. RJ 45 MDC (MDC PORT)
  • Page 17 Note The power switches of both of the monitor and the network box must be turned on for the network box to operate normally. Connects to a LAN cable to allow Internet or network access in MagicInfo mode. USB (USB Connection Terminal) Keyboard / Mouse, Mass Storage Device Compatible.
  • Page 18: Remote Control

    Remote Control Note The performance of the remote control may be affected by a TV or other electronic device operating near the LCD Display , causing a malfunction due to interference with the frequen- POWER Number Buttons / GUIDE button POWER Number Buttons / GUIDE button...
  • Page 19 This button can only be used in TV mode while a TV tuner box (sold separately) is connected. Adjusts the audio volume. + VOL - Selects a connected external input source or MagicInfo SOURCE mode. Press the button to change the input signal SOURCE. Changing the SOURCE is only allowed for external devices that are connected to the LCD Display at the time.
  • Page 20 MagicInfo Quick Launch Button. MagicInfo To use MagicInfo with an TSn-3 model, install inside the product a network box specified by Samsung and connect the MagicInfo output on the network box to [HDMI IN 2 (MAGICINFO)] on the product. Mono ↔ SAP...
  • Page 21: Tilt Angle And Rotation

    User Installation Guide Note • Be sure to call an installation expert of Samsung Electronics to install the product. • The warranty becomes invalid if the product is installed by someone other than a profes- sional authorized by Samsung Electronics.
  • Page 22: Embedded Mount Guide

    When installing the product onto a vertical wall, be sure there is a 40 mm space or more behind the product for ventilation, as shown above, and maintain the ambient temperature at 35°C or lower. Note A Samsung Electronics service center can provide details. 2. Embedded Mount guide <Side view> •...
  • Page 23: Mechanical Layout

    • At least 2 persons are needed in order to move the LCD Display. • SAMSUNG is not responsible for any product damage or any injury caused by installation at customer's discretion. Dimensions...
  • Page 24: Accessories (Sold Separately)

    • Contact a technician for installing the wall bracket. • SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. • This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.
  • Page 25: To Mount The Product On The Wall Bracket

    To mount the product on the wall bracket The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and the screw are the same) Remove the 4 screws on the back of the product. Insert the screw B into the plastic hanger.
  • Page 26: Wall Bracket Angle Adjustment

    Wall Bracket Angle Adjustment Adjust the bracket angle to -2° before installing it on the wall. Fix the product to the wall bracket. Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle.
  • Page 27 Remote Control (RS232C) Cable connections interface Bits rate Data Bits Parity Stop Bits Flow control Maximum length • Pin assignment • RS232C cable Connector : 9-pin D-Sub Cable : Cross (reversed) cable -P1- FEMALE RS232C(9 pin) TxD(No.2) RxD(No.3) GND(No.5) 9600 bps 8 bit None 1 bit...
  • Page 28: Control Codes

    • Connecting method Control codes • Get control Header 0xAA • Set control Header command 0xAA command • commanding words - ID should show hexadecimal value of assigned ID, but ID 0 should be 0xFF. <--------- ---------- command command type DATA Length type...
  • Page 29 - Every communication will be made in hexadecimals and Checksum is the sum of all remainings. If it exceeds two digits,for example, it is 11+FF+01+01=112, discard the number in the first digit like below. example)PowerOn&ID=0 Header command 0xAA 0x11 Header command 0xAA 0x11...
  • Page 30 0xAA 0xFF ERR : Error code that shows what occurred error is • Volume Control • Function Personal Computer changes volume of TV / Monitor. • Get Volume Status Header command 0xAA 0x12 • Set Volume Header command 0xAA 0x12 Volume : Volume value code to be set on TV / Monitor (0 ~ 100) •...
  • Page 31 • Set Input Source Header command 0xAA 0x14 Input Source : Input Source code to be set on TV / Monitor 0x14 0x1E 0x18 0x0C 0x04 S-Video 0x08 Component 0x20 MagicInfo 0x1F DVI_VIDEO 0x30 RF(TV) 0x40 0x21 HDMI1 0x22 HDMI1_PC 0x23 HDMI2 0x24...
  • Page 32 • Screen Mode Control • Function Personal Computer changes "Screen Mode" of TV/Monitor. Cannot be controlled when Video Wall is on. Caution Only works with models include TV. • Get Screen Mode Status Header command 0xAA 0x18 • Set Picture Size Header command 0xAA...
  • Page 33 Personal Computer recognizes the screen size of TV / Monitor. • Get Screen Size Status Header command 0xAA 0x19 • com- Header mand 0xAA 0xFF Screen Size : Screen Size of TV / Monitor (Range : 0 ~ 255, Unit : Inch) •...
  • Page 34 com- Header mand 0xAA 0xFF PIP : Same as above • com- Header mand 0xAA 0xFF ERR : Error code that shows what occurred error is • Auto Adjustment Control (PC, BNC Only) • Function Personal Computer controls PC system screen automatically. •...
  • Page 35 • Function Personal Computer converts Video Wall Mode of TV / Monitor when Video Wall is ON. Only works with TV / Monitor where Video Wall is on. Does not operate in MagicInfo • Get Video Wall Mode Header command 0xAA 0x5C •...
  • Page 36 • Get Safety Lock Status Header command 0xAA 0x5D • Set Safety Lock Enable / Disable Header command 0xAA 0x5D Safety Lock : Lock code to be set on TV / Monitor 1 : ON 0 : OFF • com- Header mand 0xAA...
  • Page 37: Connecting A Computer

    Connections Connecting a Computer There are several ways to connect the computer to the monitor. Choose one from the following options. Using the D-sub (Analog) connector on the video card. • Connect the D-sub to the 15-pin, [RGB/COMPONENT IN] port on the back of your LCD Display and the 15 pin D-sub Port on the computer.
  • Page 38: Connecting To Other Devices

    Connect the power cord for your LCD Display to the POWER port on the back of the LCD Display. Turn on the power switch. Note Contact a local SAMSUNG Electronics Service Center to buy optional items. Connecting to Other devices Note •...
  • Page 39: Connecting Av Devices

    Connecting AV Devices Connect an audio cable to [AV/COMPONENT AUDIO IN [R-AUDIO-L]] on the product and the audio port on an external device such as a VCR or DVD player. Connect a video cable to [AV IN] on the product and the video output port on the external device.
  • Page 40: Connecting Using A Hdmi Cable

    Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the [AV /COMPONENT AUDIO IN [R-AUDIO-L]] on the LCD Display . Press SOURCE on the product or remote control and select "AV". Then, start the Camcorders with a tape inserted. Note The audio-video cables shown here are usually included with a Camcorder.
  • Page 41: Connecting Using A Dvi To Hdmi Cable

    Connecting Using a DVI to HDMI Cable Connect a DVI-HDMI cable to [HDMI IN 2 (MAGICINFO)] or [HDMI IN 1] and the DVI output port on the digital device. Connect the red and white jacks of an RCA to stereo (for PC) cable to the same colored audio output terminals of the digital output device, and con- nect the opposite jack to the [RGB/DVI/DP/HDMI AUDIO IN] terminal of the LCD Display.
  • Page 42: Connecting A Dtv Set Top (Cable/Satellite) Box

    Note • Press SOURCE on the product or remote control and select "Component". • Then, start the DVD Player with a DVD disc inserted. • A RGB to component cable is optional. • For an explanation of Component video, consult your DVD manual. Connecting a DTV Set Top (Cable/Satellite) Box Connect a RGB to Component cable between the [RGB/COMPONENT IN] port on the LCD Display and the P...
  • Page 43: Connecting To An Audio System

    Connecting to an Audio System Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and [AUDIO OUT] on LCD Display. Connecting to MAGICINFO OUT Connect the [MAGICINFO OUT] terminal and the [HDMI IN 2 (MAGICINFO)] terminal on the product using the DP to HDMI cable.
  • Page 44: Connecting A Lan Cable

    Connecting a LAN Cable Connect the LAN cable between the [LAN] port on the product and the [LAN] port on your Connecting a USB devices You can connect USB devices such as a mouse or keyboard.
  • Page 45: Using The Software

    Prepare a blank disk and download the driver Program file at the Internet web site shown here. Internet web site : http://www.samsung.com/ Installing the Monitor Driver (Automatic) Insert CD into the CD-ROM drive. Click "Windows". Choose your monitor model in the model list, then click the "OK" button.
  • Page 46: Installing The Monitor Driver (Manual)

    Note This monitor driver is certified by Microsoft, and installing it will not damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ Installing the Monitor Driver (Manual) ® Microsoft Windows Vista™‚ Operating System Insert your Manual CD into your CD-ROM drive.
  • Page 47 This monitor driver is under certifying MS logo, and this installation will not damage your system. The certified driver will be posted on Samsung Monitor homepage. Click "Update Driver..." in the "Driver" tab. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer".
  • Page 48 Select the model that matches your monitor from the list of monitor models on the screen, and click "Next". 10. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence. ® ® Microsoft Windows XP Operating System...
  • Page 49 Insert CD into the CD-ROM drive. Click "Start" → "Control Panel", then click the "Appearance and Themes" icon. Click "Display" icon and choose the "Settings" tab then click "Advanced...". Click the "Properties" button on the "Monitor" tab and select "Driver" tab. Click "Update Driver..."...
  • Page 50 Then click "OK" button. Note This monitor driver is certified by Microsoft, and this installation will not damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ Click the "Close" button, then click the "OK" button continually.
  • Page 51 10. Monitor driver installation is completed. ® ® Microsoft Windows 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. Choose "OK" button on the "Insert disk" window. Click the "Browse" button on the "File Needed" window. Choose A:(D:\Driver), then click the "Open"...
  • Page 52 If you can see the "Digital Signature Not Found" window, then click the "Yes" button. Then click the "Finish" button and the "Close" button. ® ® Microsoft Windows Millennium Operating System Click "Start", "Setting", "Control Panel". Double click the "Display" icon. Select the "Settings"...
  • Page 53 Set a Keyboard for your computer. The next screen is for setting your monitor. First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.) Set a vertical frequency for your monitor. (You can enter the frequency directly.) Enter the model name of your monitor.
  • Page 54 General Control Panel Menu 1. Mapping The control panel can be used to make adjustments or configurations using a USB connection and supports multiple touchscreens connected to the same PC. The panel provides basic information for the touchscreen and allows for calibration. If several touchscreens are moun- ted on the PC and the status is set to “multi-screens display,”...
  • Page 55 “ReCalibrate”, “OK” and “Cancel” buttons will appear after the calibration. Select “ReCali- brate” to calibrate again, “OK” to save and exit, or “Cancel” to exit without saving. Settings The Settings window is split into 8 areas (FIG. 7): Modes Enable Touch Hide Cursor Enable Double Click Enable Right Click...
  • Page 56 Mouse functions are emulated, including left-clicking, moving, unclicking, and dragging. This function is recommended if writing, drawing or dragging map is required. Options 1. Enable Touch Enable (default) or disable the touchscreen. 2. Hide Cursor The mouse cursor is not used in some applications; this function allows you to hide the cursor without disabling the mouse function.
  • Page 57: Uninstalling The Driver

    Both : A click is recognized when your finger contacts the touchscreen and again when you lift your finger off the screen. PC Speaker : After installing the driver, you will hear a beep sound by default when a PC card is started. You can change the cycle and sound of the beep. Sound Card : Sound is heard via the sound card.
  • Page 58 3. Enable Drag Delay This function shows the time in milliseconds “Drag Delay” will take to be enabled after the option is touched. Drag Delay may be adjusted (in milliseconds) to the correct value if an object cannot be precisely selected or if the cursor jitters when you touch the touchscreen. MDC (Multiple Display Control) Installation Insert the installation CD into the CD-ROM drive.
  • Page 59: Installation Problems

    Note If the file location is not specified, the Program will be installed in the default file location. The "Start Copying Files" window will appear. Confirm the file location and click "Next." The installation progress screen will appear. The "InstallShield Wizard Complete" screen will appear. Click "Finish." Note Select "...
  • Page 60: Main Screen

    Therefore, a serial cable should be connected between the serial port on a PC and the serial port on a display. Main Screen Click Start > Program > Samsung > MDC System to start the program. Select a set to see the volume of the selected set within the slider.
  • Page 61 Main Icons Remote control Safety Lock Port Selection Lamp Control Option... Dropdown Selectors Use the main icons to switch into each screen. Allows you to enable or disable the remote control signal receiving function of the display unit. Set the Safety Lock function. When setting the Lock function, you can only operate power and lock buttons on the remote control and set.
  • Page 62: Port Selection

    Port Selection 1. The Multiple Display Control is originally set to COM1. 2. If any port other than COM1 is used, COM1 through COM4 can be selected in the Port Selection Menu. 3. If the exact port name that is connected to the LCD Display using a serial cable is not selected, communication will be unavailable.
  • Page 63 Info Grid shows some basic information necessary to System. (Power Status) 2) Input 3) Image Size 4) On Timer 5) Off Timer 2. Selects displays you want to adjust using the Select button or checkboxes. System allows controlling some of the functions of the selected display. 1) Power On/Off...
  • Page 64: Input Source

    - Turns the power of the selected display On/Off. 2) Volume - Controls the volume level of the selected display. It receives the volume value of the selected display from the sets and displays it in the slider. (If you deselect a single display or all displays, the default value 10 will be restored.) (Mute On/Off) - Turns on/off the Mute function of the selected display.
  • Page 65 • PC Mode Info Grid shows some basic information necessary to Input Source Control. - Changes the Input Source of the selected display to PC. - Changes the Input Source of the selected display to BNC. - Changes the Input Source of the selected display to DVI. - Changes the Input Source of the selected display to TV.
  • Page 66: Image Size

    - Changes the Input Source of the selected display to DTV. - Changes the Input Source of the selected display to AV. S-Video - Changes the Input Source of the selected display to S-Video. Component - Changes the Input Source of the selected display to Component. MagicInfo - The Input source of MagicInfo works only on MagicInfo model.
  • Page 67 3) Input - Info Grid displays only the displays whose Input Source is PC, BNC, DVI and DP. 4) PC Source - Click Image Size in the main menu to display the PC, BNC, DVI and DP tabs. - The Image Size Control button controls Image Size available for PC, BNC, DVI and DP. 5) Video Source - Using the Image Size adjustment button, you can adjust the Image Size to a value available in the PC, BNC, DVI and DP.
  • Page 68 Time 1. Click Time of the main icons and the Time Control screen appears. Info Grid shows some basic information necessary to Time Control. 1) Set clock - Set the current time for the selected display (PC Time). - To change the current time, first change the PC Time. 2) Timer - Sets up Timer1, Timer2, Timer3 and Holiday Management.
  • Page 69 1) On Time - Sets the time in hours, in minutes and as AM/PM for turning the selected monitor on. 2) Off Time - Sets the time in hours, in minutes and as AM/PM for turning the selected monitor off. 3) Volume - Selects the volume when the selected monitor is turned on.
  • Page 70: Pip Size

    - Adds the specified date. - Deletes the schedule in the selected line. The Holiday Management function can be turned on or off in the Timer setup menu. The Input source of MagicInfo works only on MagicInfo model. The Input source of TV works only on TV model. Time Control is available only for the displays for which the power status is ON.
  • Page 71: Pip Source

    PIP Size can be controlled with turning on the LCD Display power. PIP Source 1. Click PIP of the main icons and the PIP control screen appears. Info Grid shows some basic information necessary to PIP Source Control. 1) PIP Source - PIP Source can be controlled with turning on the LCD Display power.
  • Page 72 The PIP Control feature is available only for the displays whose power status is ON and the PIP function is set to ON. Settings Picture 1. Click Settings of the main icons and the Settings Control screen appears. Basic information required to adjust the Picture is displayed in the main menu. Settings for the selected monitor will be displayed if one of the connected monitors is selected, and the default settings will be displayed if all monitors are selected by clicking All and Select.
  • Page 73 - Adjusts the Dynamic Contrast for the selected display. HDMI2 may not be supported depending on the product. Brightness Sensor may not be supported depending on the product. The Input source of MagicInfo works only on MagicInfo model. Color Temp is only enabled if the Color Tone is set to Off. The Input source of TV works only on TV model.
  • Page 74 - Available only for NTSC. 7) Color Tone - Adjusts the Color Tone for the selected display. 8) Color Temp - Adjusts the Color Temp for the selected display. 9) Brightness Sensor - Adjusts the Brightness Sensor for the selected display. 10) Dynamic Contrast - Adjusts the Dynamic Contrast for the selected display.
  • Page 75: Image Lock

    4) Balance - Adjusts Balance of the selected display. 5) SRS TS XT - SRS TS XT Sound ON/OFF of the selected display. 6) Sound Select - Select either Main or Sub when PIP is On. The Input source of MagicInfo works only on MagicInfo model. The Input source of TV works only on TV model.
  • Page 76: Lamp Control

    Maintenance Lamp Control 1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen. An "Info Grid" showing several basic data items appears. 1) Maintenance - Allows the Maintenance Control function for all input sources. 2) Lamp Control - Automatically adjusts the backlight of the selected display at a specified time.
  • Page 77: Video Wall

    1) Scroll - This function is used to remove the afterimages that occur when a still screen is displayed on the selected display for a long time. 2) Pixel Shift - This allows the screen to be moved finely at the specified time interval. 3) Safety Screen - The Safety Screen function is used to prevent afterimages from occurring when a still screen is displayed on the monitor for a long time.
  • Page 78 1) Video Wall - A Video Wall is a set of video screens that are connected together, so that each screen shows a part of the whole picture or so that the same picture is repeated on each screen. 2) Video Wall Control - Video Wall properties can be configured.
  • Page 79: Troubleshooting

    Full Natural 3) Video Wall (Screen divider) - The screen can be divided into. You can select a number of screens with a different layout when dividing. Select a mode from Screen divider. Select a display from Display Selection. The place will be set up by pressing a number in the selected mode. The maximum number of monitors that can be arranged: Horizontal X Vertical = 100 Up to 15 monitors can be arranged in a row.
  • Page 80 Settings Value Display In Multiple Display Mode When there are more than one displays connected, the settings values are displayed as follows. 1. No selection: Displays the Factory Default Value. 2. Selected one display: Fetches and displays the settings value for the selected display. 3.
  • Page 81: Main Screen

    Introduction Unlike the previous method which used the serial data communication specifications RS-232C, an Ethe function has been added. Connect the first display device and the PC by entering the IP address. To connect to another display use an RS-232C serial cable. Refer to the figure above. Main Screen...
  • Page 82: Main Icons

    Click Start > Program > Samsung > MDC System to start the program. Select a set to see the volume of the selected set within the slider. Main Icons Add a Device Remote Control Safety Lock Fault Device Alert Use the main icons to switch into each screen.
  • Page 83: Add A Device

    Use Control Tools to control displays. 10. Switches the OSD function On/Off. - May not be supported depending on the product. <Note> The remote control Enable/Disable function operates whether or not the power is On/Off applies to all displays connected to the MDC. However, regardless of the status at the tim MDC is shut down, the remote control signal receiving function of all displays is initialized Enable when the MDC is closed.
  • Page 84 Info Grid shows some basic information necessary to System. (Power Status) 2) Input 3) Image Size 4) On Timer 5) Off Timer 2. Selects displays you want to adjust using the Select All button or checkboxes.
  • Page 85 System allows controlling some of the functions of the selected display. 1) Power On/Off - Turns the power of the selected display On/Off. 2) Volume - Controls the volume level of the selected display. It receives the volume value of the selected display from the sets and displays it in the slider. (If you deselect a single display or all displays, the default value 10 will be restored.) (Mute On/Off) - Turns on/off the Mute function of the selected display.
  • Page 86 1) Source OSD - Sets whether the Source OSD will be displayed to indicate when the Source is changed. 2) Not Optimum Mode OSD - Sets whether the Optimum Mode OSD will be displayed to indicate if the current mode is not supp 3) No Signal OSD - Sets whether the No Signal OSD will be displayed to indicate when there is no signal.
  • Page 87: Input Source

    1) Select or clear all the added devices; or refresh or delete selected devices. 2) The IP Address, ID (Ethernet or Serial), Mac Address and connection status of the connected monito 3) It can automatically check whether DHCP IP is set and then set the IP address. 4) It can automatically or manually set and then apply the IP Address, Subnet and Gateway of the sele Input Source Click Input Source of the main icons and the Input Source control screen appears.
  • Page 88 • PC Mode...
  • Page 89 Info Grid shows some basic information necessary to Input Source Control. 1) PC - Changes the Input Source of the selected display to PC. 2) BNC - Changes the Input Source of the selected display to BNC. 3) DVI - Changes the Input Source of the selected display to DVI. 4) TV - Changes the Input Source of the selected display to TV.
  • Page 90: Image Size

    11) DP - Switches the input source for the selected display to DP. 12) Channel - Channel arrow appears when the Input Source is TV. HDMI2 may not be supported depending on the product. DP may not be supported depending on the product. The Input Source Control feature is available only for the displays whose power status is TV Source can be selected only in products with TV and controlling channels is allowed o Input Source is TV.
  • Page 91 - Shows the current Image Size of the display in use. 3) Input - Info Grid displays only the displays whose Input Source is PC, BNC, DVI and DP. 4) PC Source - Click Image Size in the main menu to display the PC, BNC, DVI and DP tabs. - The Image Size Control button controls Image Size available for PC, BNC, DVI and DP.
  • Page 92 Info Grid shows some basic information necessary to Image Size Control. 1) To adjust Image Size in TV, AV, S-Video, Component, HDMI1, HDMI2 or DTV mode, click the Video tab. Select the display you want to adjust by using the Select All button or by checking the checkbox. 2) Info Grid displays only the display having TV, AV, S-Video, Component, HDMI1, HDMI2 or DTV as in 3) Switch Image Size of the selected display randomly.
  • Page 93 Info Grid shows some basic information necessary to Time Control. 1) Clock Set - Set the current time for the selected display (PC Time). - To change the current time, first change the PC Time. 2) Timer - Sets up Timer1, Timer2, Timer3 and Holiday Management. 3) Shows whether Timer is activated.
  • Page 94 1) On Time - Sets the time in hours, in minutes and as AM/PM for turning the selected monitor on. 2) Off Time - Sets the time in hours, in minutes and as AM/PM for turning the selected monitor off. 3) Volume - Selects the volume when the selected monitor is turned on.
  • Page 95 1) Specifies the date. 2) Delete All - Deletes all of the holidays. 3) Add - Adds the specified date. - Deletes the schedule in the selected line. The Holiday Management function can be turned on or off in the Timer setup menu. The Input source of MagicInfo works only on MagicInfo model.
  • Page 96 Info Grid shows some basic information necessary to PIP Size Control. 1) PIP Size - Shows the current PIP Size of the display in use. 2) OFF - Turns off the PIP of the selected display. 3) Large - Turns on the PIP of the selected display and changes the size to Large. 4) Small - Turns on the PIP of the selected display and changes the size to Small.
  • Page 97: Pip Source

    PIP Source 1. Click PIP of the main icons and the PIP control screen appears. Info Grid shows some basic information necessary to PIP Source Control. 1) PIP Source - PIP Source can be controlled with turning on the LCD Display power. 2) PC - Changes the source of the PIP of the selected display to PC.
  • Page 98 9) Component - Changes the source of the PIP of the selected display to Component. 10) HDMI1/HDMI2 - Changes the source of the PIP of the selected display to HDMI. 11) DP - Switches the PIP Source of the selected Display to DP. Some of the PIP Sources may not be available for selection, depending on the input sour of the Main Screen.
  • Page 99 Basic information required to adjust the Picture is displayed in the main menu. Settings for the selec monitor will be displayed if one of the connected monitors is selected, and the default settings will b displayed if all monitors are selected by clicking All and Select. If a value is changed in this screen, t mode will automatically switch to custom mode.
  • Page 100 Basic information required to adjust settings is displayed. Settings for the corresponding SET will be and displayed on the slider if a display ID is selected, and the default settings will be displayed if all are selected by clicking All and Select. If a value is changed in this screen, the current mode will aut switch to custom mode.
  • Page 101 - Adjusts the Color Temp for the selected display. 9) Brightness Sensor - Adjusts the Brightness Sensor for the selected display. 10) Dynamic Contrast - Adjusts the Dynamic Contrast for the selected display. Brightness Sensor may not be supported depending on the product. The Input source of MagicInfo works only on MagicInfo model.
  • Page 102: Image Lock

    SET will be imported and displayed on the slider if a display ID is selected, and the default settings w displayed if all display IDs are selected by clicking All and Select. If a value is changed in this screen current mode will automatically switch to custom mode.
  • Page 103: Maintenance

    Info Grid shows some basic information necessary to Settings Control. 1) Image Lock - Available only for PC, BNC. 2) Coarse - Adjusts Coarse of the selected display. 3) Fine - Adjusts Fine of the selected display. 4) Position - Adjusts Position of the selected display. 5) Auto Adjustment - Self-Adjust to the incoming PC signal.
  • Page 104 1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen. An "Info Grid" showing several basic data items appears. 1) Maintenance - Allows the Maintenance Control function for all input sources. 2) Lamp Control - Automatically adjusts the backlight of the selected display at a specified time.
  • Page 105 Maintenance Scroll 1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen. 1) Scroll - This function is used to remove the afterimages that occur when a still screen is displayed on the sele display for a long time.
  • Page 106: Video Wall

    set to 10, 20, 30, 40 or 50. For the All White and Pattern type, it can be set to 1, 5, 10, 20 or The Maintenance Control feature is available only for the displays whose power status is ON The Input source of MagicInfo works only on MagicInfo model.
  • Page 107 1) On / Off - Turns on/off the Video Wall function of the selected display. 2) Format - The format can be selected to see a divided screen. Full Natural 3) Video Wall (Screen divider) - The screen can be divided into. You can select a number of screens with a different layout when dividing.
  • Page 108: Troubleshooting

    The maximum number of monitors that can be arranged: Horizontal X Vertical = 100 Up to 15 monitors can be arranged in a row. The maximum value for Horizontal is 6 if Vertical i while the maximum value for Vertical is 6 if Horizontal is set to 15. 4) Viewing Screen Splits - You can view and change the layout of screens using the Screen Divider settings.
  • Page 109 Settings Value Display In Multiple Display Mode When there are more than one displays connected, the settings values are displayed as follows. 1. No selection: Displays the Factory Default Value. 2. Selected one display: Fetches and displays the settings value for the selected display. 3.
  • Page 110: Adjusting The Lcd Display

    To watch TV on the product, connect a TV tuner box (sold separately). Using MagicInfo To use MagicInfo with an TSn-3 model, install inside the product a network box specified by Samsung and connect the MagicInfo output on the network box to [HDMI IN 2 (MAGICIN- FO)] on the product. Source List Use to select PC, HDMI or other external input sources connected to the LCD Display.
  • Page 111 TV- Enabled if a TV tuner box is connected. Note The [RGB/COMPONENT IN] port is compatible with RGB (PC) and Component signals. However, the picture may display abnormally if the connected external input signal is different from the selected video signal. Note The PIP function is not available when Video Wall is On.
  • Page 112 • PC : DVI / AV / HDMI1 / HDMI2 / DisplayPort • DVI : PC • AV : PC • HDMI : PC • DisplayPort : PC Size Changes the Size of the PIP window. Position Changes the Position of the PIP window. Transparency Adjusts the Transparency of PIP windows.
  • Page 113: Source Autoswitch Settings

    Edit Name Name the input device connected to the input jacks to make your input source selection easier. VCR / DVD / Cable STB / HD STB / Satellite STB / AV Receiver / DVD Receiver / Game /Camcorder / DVD Combo / DHR / PC / DVI PC / DVI Devices Note •...
  • Page 114: Source Autoswitch

    Source AutoSwitch When the Source AutoSwitch is On, the display video source will automatically be searched for active video. The Primary Source selection will be activated, if the current video source is not recognized. Secondary source selection will become active, if no primary video source is available. If the primary or secondary source is not recognized, the display will search again, if no active video is found the display will show the no-input-signal message.
  • Page 115: Secondary Source

    To watch TV on the product, connect a TV tuner box (sold separately). Using MagicInfo To use MagicInfo with an TSn-3 model, install inside the product a network box specified by Samsung and connect the MagicInfo output on the network box to [HDMI IN 2 (MAGICIN- FO)] on the product. Mode...
  • Page 116 Note Not available when Dynamic Contrast is set to On. Information Recommended for communicating exact information (e.g. public information). Advertisement Recommended for displaying advertisements (e.g. videos or indoor or outdoor ads). Custom Custom By using the on-screen menus, the contrast and brightness can be changed to your personal preference.
  • Page 117: Color Tone

    • Mode 1 Sets the picture brighter than Natural. • Mode 2 Sets the picture darker than Mode 1. • Mode 3 Increases the contrast between dark and bright colors. Color Tone Note Not available when Dynamic Contrast is set to On. The Color tones can be changed.
  • Page 118: Color Temp

    Blue Color Temp. Color Temp. is a measure of the 'warmth' of the image Colors. Note This function is enabled when Mode is set to Custom, and Dynamic Contrast and Color Tone are Off. Image Lock Image Lock is used to fine-tune and get the best image by removing noise that creates unstable images with jitters and shakiness.
  • Page 119: Auto Adjustment

    Auto Adjustment The values of Fine, Coarse, Position are adjusted automatically. By changing the resolution in the control panel, the auto function is performed. Note Available in PC mode only. Signal Balance This is used to make up for the weak RGB signal transmitted by a long signal cable. Note •...
  • Page 120: Pip Picture

    G-Offset B-Offset Size The Size can be switched. 16:9 PIP Picture Adjusts the PIP Screen Settings. Note • Available Modes: PIP On Contrast Adjusts the Contrast of the PIP window on the screen. Brightness Adjusts the Brightness of the PIP window on the screen. Sharpness Adjusts the Sharpness of the PIP window on the screen.
  • Page 121: Dynamic Contrast

    Note PIP input only operates in AV, HDMI, or Component mode. Tint Adds a natural tone to the PIP window. Note PIP input only operates in AV, HDMI, or Component mode. Dynamic Contrast Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an optimum contrast.
  • Page 122: Picture Reset

    To watch TV on the product, connect a TV tuner box (sold separately). Using MagicInfo To use MagicInfo with an TSn-3 model, install inside the product a network box specified by Samsung and connect the MagicInfo output on the network box to [HDMI IN 2 (MAGICIN- FO)] on the product. Mode The LCD Display has four automatic picture settings ("Dynamic", "Standard", "Movie"...
  • Page 123 Movie Custom Custom By using the on-screen menus, the contrast and brightness can be changed to your personal preference. Note Not available when Dynamic Contrast is set to On. Contrast Adjusts the Contrast. Brightness Adjusts the Brightness. Sharpness Adjusts the picture Sharpness. Color Adjusts the picture Color.
  • Page 124 The Color tones can be changed. The individual Color components are also user adjustable. Note Not available when Dynamic Contrast is set to On. Cool2 Cool1 Normal Warm1 Warm2 Note • If you set the Color Tone to Cool2, Cool1, Normal, Warm1, or Warm2, the Color Temp.
  • Page 125: Digital Nr (Digital Noise Reduction)

    4:3 - Sets the picture to 4:3 normal mode. Screen Fit - Displays the input scenes as they are without any cutoff when HDMI 720p, 1080i, 1080p signals are input. Custom - Changes the resolution to suit the user's preferences. Note •...
  • Page 126: Film Mode

    Note For Timing which can be used for both the PC and the DTV in HDMI mode, HDMI Black Level will be activated. Film Mode Film Mode calibrates unnatural picture when watching a movie (24 frames) played on a TV (30 frames).
  • Page 127 Dynamic Contrast Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an optimum contrast. Note This function is disabled when PIP or Energy Saving is On. Lamp Control Adjusts the inverter lamp in order to reduce energy consumption. Note Not available when Dynamic Contrast is set to On.
  • Page 128: Available Modes

    To watch TV on the product, connect a TV tuner box (sold separately). Using MagicInfo To use MagicInfo with an TSn-3 model, install inside the product a network box specified by Samsung and connect the MagicInfo output on the network box to [HDMI IN 2 (MAGICIN- FO)] on the product. Mode The LCD Display has a built-in high fidelity stereo amplifier.
  • Page 129: Auto Volume

    Custom The sound settings can be adjusted to suit your personal preferences. Note • You can hear the sound even when sound value is set to 0. • If you adjust sound using Custom function, Mode will turn to Custom mode. Bass Emphasizes low frequency audio.
  • Page 130: Sound Select

    experience through any two-speaker playback system, including internal television speakers. It is fully compatible with all multichannel formats. Sound Select Enable the sound of either the primary or secondary display in PIP mode. Note Available when PIP is set to On. Main Speaker Select When you use the product with it connecting to a Home Theater, turn the internal speakers...
  • Page 131 To watch TV on the product, connect a TV tuner box (sold separately). Using MagicInfo To use MagicInfo with an TSn-3 model, install inside the product a network box specified by Samsung and connect the MagicInfo output on the network box to [HDMI IN 2 (MAGICIN- FO)] on the product. Language You can choose one of 13 languages.
  • Page 132: Clock Set

    Clock Set Current Time Setting. Sleep Timer Turns the LCD Display off automatically at certain times. Timer1 / Timer2 / Timer3 You can set the LCD display to automatically turn on or off at a specified time. Note • Only enabled when the clock is set using the Clock Set menu. •...
  • Page 133: Holiday Management

    • Holiday : When choose Apply, timer is not available on holiday; when choose Don’t apply, timer is available on holiday. Holiday Management • You can register holidays. • Delete Selected You can delete selected holidays. Note • Only enabled when registered holidays are selected. •...
  • Page 134: Menu Transparency

    Menu Transparency Change the transparency of the background of the OSD. High Medium Opaque Safety Lock Change PIN The password can be changed. The preset password for the LCD Display is "0000". Note If you forgot your password, press the remote buttons password to "0000."...
  • Page 135: Energy Saving

    Energy Saving This feature adjusts the power consumption of the unit in order to save energy. Video Wall A Video Wall is a set of video screens connected together, so that each screen shows a part of the whole picture or where the same picture is repeated on each screen. When the Video Wall is on, you can adjust the Video Wall screen setting.
  • Page 136: Screen Position

    • Full Provides a full screen without any margins. • Natural Displays a natural image with the original aspect ratio intact. Horizontal Sets how many parts the screen should be divided horizontally. Fifteen adjustment levels: 1~15. Note If Vertical is set to 15, the maximum value for Horizontal is 6. Vertical Sets how many parts the screen should be divided vertically.
  • Page 137: Safety Screen

    • Select a mode in Screen Position. • Select a display in Display Selection. • The selection will be set up by pressing a number in the selected mode. • The screen can be split into a maximum of 100 sub-screens. Note When more than four displays are connected, we recommend a resolution of XGA (1024*768) or greater to prevent any picture degradation.
  • Page 138 Vertical Sets how many pixels the screen moves vertically. Five adjustment levels: 0, 1, 2, 3, and 4. Time Set the time interval for performing the horizontal or vertical movement, respectively. Timer Timer You can set the timer for Screen Burn Protection. If you start the operation to erase any residual image, the operation will be performed for the set period of time and then automatically finish.
  • Page 139 Mode You can change the Safety Screen Type. • • Eraser • Pixel Period Use this function to set the execution period for each mode set in the timer. Time Within the set period of time specify a time for execution. This function prevents after-images on the screen by moving long black and white vertical lines.
  • Page 140: Side Gray

    Eraser This function prevents after-images on the screen by moving a rectangular pattern. Pixel This function prevents after-images by moving many pixels on the screen. Side Gray Select the brightness of the grey for the screen background. • • Light •...
  • Page 141: Power On Adjustment

    60Hz or 1366 x 768 @ 60Hz, by using this function(Resolution Select), you can have the picture displayed on the screen in the specified resolution. Note Available in PC mode only. 1024 X 768 1280 X 768 1360 x 768 1366 X 768 Note Selecting the menu is only allowed when the graphics resolution is set to 1024 x 768 @...
  • Page 142: Fan & Temperature

    Fan & Temperature Protects the product by detecting the fan speed and internal temperature. Fan Control Selects auto or manual for the fan speed settings. • Auto • Manual Fan Speed Setting Sets the fan speed within a range of 0 and 100. Note Enabled when Fan Control is set to Manual.
  • Page 143: Current Temperature

    Refer to "Specifications" herein for details about operating conditions. • It is best to set Fan Control to Auto when you change the Temperature Control setting. Current Temperature Shows the current temperature of the product. Auto Power Enables or disables Auto Power for the product. •...
  • Page 144: User Auto Color

    User Auto Color Auto Color Automatically adjusts the Colors. Reset Resets the Color settings. Note Enabled only in PC mode. Standby Control Sets the standby mode, which will be activated when no input signal is detected. • A message will read No Signal if no input signal is detected. •...
  • Page 145 Lamp Schedule Adjusts the luminance to a user-specified value at a specified time. OSD Display Displays or hides a menu item on the screen. Source OSD • • Not Optimum Mode OSD • • No Signal OSD...
  • Page 146: Software Upgrade

    • • MDC OSD • • Software Upgrade Performs a software upgrade. Connect the product to a computer via a digital signal such as DVI or HDMI. Click the BMP image file converted from an SW code. The image below will appear on the screen of the product.
  • Page 147: Setup Reset

    Note • This only operates with a digital signal, such as in DVI, HDMI1, or HDMI2 mode. (The input resolution must be identical to the panel resolution.) • In HDMI1 and HDMI2 modes, the timing values used for both the PC and TV are only supported if the Edit Name is set to PC or DVI PC.
  • Page 148 Using MagicInfo To use MagicInfo with an TSn-3 model, install inside the product a network box specified by Samsung and connect the MagicInfo output on the network box to [HDMI IN 2 (MAGICIN- FO)] on the product. Multi Control Assigns an individual ID to the SET.
  • Page 149 To watch TV on the product, connect a TV tuner box (sold separately). Using MagicInfo To use MagicInfo with an TSn-3 model, install inside the product a network box specified by Samsung and connect the MagicInfo output on the network box to [HDMI IN 2 (MAGICIN- FO)] on the product. Note •...
  • Page 150 Adjusting the LCD Display You can select an Application to be executed in your computer when Windows starts. 2. Select TCP/IP - step 2 In step 2 of MagicInfo Setup Wizard, you don’t have to go to Network Setting on the desktop to make your settings for TCP/IP.
  • Page 151 Adjusting the LCD Display When using multiple languages, you can choose and set a specific language among them. 4. Select Screen Type - step 4 You can select which rotation type will be applied to your device. 5. Setup Information...
  • Page 152 Adjusting the LCD Display Shows the settings that have been selected by the user. Note If the MagicInfo icon is not displayed on the notification area, double click the MagicInfo icon on the window desktop. The icon will appear.
  • Page 153: Self-Test Feature Check

    Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check Turn off both your computer and the LCD Display. Unplug the video cable from the back of the computer. Turn on the LCD Display.
  • Page 154: Symptoms And Recommended Actions

    2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel). Symptoms and recommended Actions Note A LCD Display recreates visual signals received from the computer. Therefore, if there is a problem with the computer or the video card, this can cause the LCD Display to become blank, have poor Coloring, become noisy, etc.
  • Page 155: Problems Related To The Screen

    Check if the signal cable between the computer and the LCD Display is securely con- nected. (Refer to Connecting a Computer) Problems related to the Screen Note Problems related to the LCD Display screen and their solutions are listed. The screen is blank and the power indicator is off. Ensure that the power cord is firmly connected and the LCD Display is on.
  • Page 156: Problems Related To Audio

    The screen Color is inconsistent. Adjust the Color Control option in the OSD adjustment menu. The Color image is distorted by dark shadows. Adjust the Color Control option in the OSD adjustment menu. The Color white is poor. Adjust the Color Control option in the OSD adjustment menu. The Power Indicator blinks.
  • Page 157 Check if a special fluorescent or neon lamp is on in the vicinity. Q & A How can I change the frequency? The frequency can be changed by reconfiguring the video card. Note That video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.) How can I adjust the resolution? Windows XP:...
  • Page 158: Specifications

    Weight 20.8 Kg / 45.9lbs VESA Mounting Interface 200.0 mm X 200.0 mm Environmental considerations Operating 320TSn-3 31.5 inch / 80cm 697.68 mm(H) x 392.25 mm(V) 30~81 kHz 56~85 Hz 1366 x 768 @ 60Hz 1920 x 1080 @ 60Hz 787.4 mm x 553.1 mm x 311.0 mm / 31.0 x 21.8 x 12.2...
  • Page 159 Environmental considerations Storage Plug and Play Capability This LCD Display can be installed on any Plug & Play compatible system. The interaction of the LCD Display and the computer systems will provide the best op- erating conditions and LCD Display settings. In most cases, the LCD Display installation will proceed automatically, unless the user wishes to select alternate settings.
  • Page 160 State Power Indicator Power Consumption (Typical) Note • The actual power consumption may be different from the indicated power consumption above if the system conditions or settings are changed. • To stop any power consumption, turn off the switch or disconnect the power cable on the back.
  • Page 161 Specifications Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Hor- izontal Cycle is called the Horizontal Frequency. Unit: kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the...
  • Page 162: For A Better Display

    Information For a Better Display Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFT- LCD.
  • Page 163 Power Off, Screen Saver, or Power Save Mode • Turn the power off for 2 hours after 12 hours in use • Set the Monitor to power off with the PC Display Properties Power Scheme. • Use a Screen saver if possible - Screen saver in one Color or a moving image is recommended.
  • Page 164 Change the characters Color periodically • Use Bright Colors with little difference in luminance. - Cycle : Change the characters Color and background Color every 30 minutes • Every 30 minutes, change the characters with movement. • Have the images and logo cycle periodically. - Cycle: Display moving image together with Logo for 60 seconds after 4 hours in use.
  • Page 165 Information • Apply the Screen Erasing function - Symptom: 2 Vertical blocks move while erasing the display...
  • Page 166 Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care Center. CANADA MEXICO U.S.A ARGENTINA BRAZIL CHILE COLOMBIA COSTA RICA DOMINICA ECUADOR EL SALVADOR GUATEMALA HONDURAS JAMAICA NICARAGUA...
  • Page 167 SERBIA 0700 SAMSUNG (0700 726 http://www.samsung.com 7864) SLOVAKIA 0800 - SAMSUNG (0800-726 http://www.samsung.com/sk 786) SPAIN 902 - 1 - SAMSUNG (902 172 http://www.samsung.com 678) SWEDEN 0771 726 7864 (SAMSUNG) http://www.samsung.com SWITZERLAND 0848 - SAMSUNG (7267864, http://www.samsung.com/ch CHF 0.08/min) 0330 SAMSUNG (7267864)
  • Page 168 KYRGYZSTAN 00-800-500-55-500 TADJIKISTAN 8-10-800-500-55-500 UKRAINE 0-800-502-000 BELARUS 810-800-500-55-500 MOLDOVA 00-800-500-55-500 AUSTRALIA 1300 362 603 NEW ZEALAND 0800 SAMSUNG (0800 726 http://www.samsung.com 786) CHINA 400-810-5858 HONG KONG (852) 3698 - 4698 INDIA 3030 8282 1800 3000 8282 INDONESIA 0800-112-8888 021-5699-7777 JAPAN...
  • Page 169 800-SAMSUNG (726-7864) http://www.samsung.com Africa 0800-SAMSUNG (726-7864) http://www.samsung.com 0860-SAMSUNG (726-7864) http://www.samsung.com The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The dis- tance between two dots of the same Color is called the 'Dot Pitch'.
  • Page 170: Correct Disposal

    Correct Disposal Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only (Applicable in the European Union and other European countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life.
  • Page 171 Reproduction in any manner whatsoever without the written permission of Samsung Elec- tronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this ma- terial.

This manual is also suitable for:

320tsn - syncmaster - 32" lcd flat panel display

Table of Contents