Keep drill bits clean and sharp for best and safest performance. Follow the
3
instructions for lubrication and changing accessories.
Remove ill fitting clothing. Remove ties, watches, rings & loose jewellery. Contain long hair.
3
Locate the drill in a suitable working area, keep area clean and tidy and free from
3
unrelated materials. Ensure there is adequate lighting.
Maintain correct balance and footing. Ensure floor is not slippery. Wear non-slip shoes.
3
Secure non-stable work piece with a clamp, vice or other adequate holding device.
3
3 Avoid unintentional starting.
DO NOT force the drill to achieve a task it was not designed to perform.
7
DO NOT allow untrained persons to operate the drill.
7
DO NOT get the drill wet or use in locations where there is damp or condensation.
7
DO NOT operate the drill if damaged.
7
DO NOT use drill in an area where paint fumes, solvents or flammable liquids pose a
7
potential hazard. Keep flammable material away from the drill when operating.
Flammable waste, such as wiping or cleaning rags, must be placed in a closed metal
container and disposed of correctly.
DO NOT exceed the rated capacity of the drill.
7
DO NOT operate the drill with parts missing as this may cause failure or personal injury.
7
DO NOT operate the drill when you are tired, under the influence of alcohol, drugs or
7
intoxicating medication.
When not in use switch the drill off, remove plug from the power supply and do not
3
leave until the tool has come to a complete stop.
2. dEsCriPTiON
The GDM120B (bench mounted) and GDM160F (floor mounted) variable speed
drills are suitable for light industrial, agricultural and woodworking applications. The
drills are fitted with flip-up safety guards and "No Volt Release" switches which prevent
accidental restart after a mains power interruption. A rack and pinion feed shaft with
preset depth control for repetitive work is also included. Both have Morse taper
spindles to accept taper shank bits. Mortice attachments and work clamps are also
available for these drills, contact your local Sealey dealer for information.
3. TECHNiCal sPECiFiCaTiONs
MOdEl No:
drilling Capacity (Chuck size):
spindle Nose Taper:
swing:
spindle centre to column:
spindle travel:
Number of speeds:
speed range:
Maximum distance spindle to Table:
Maximum distance spindle to Base:
Working Table surface size:
Working Base surface size:
Overall Base size:
Column diameter:
Collar diameter:
Overall Height:
Motor Power:
input Power:
Weight:
Optional Keyless Chuck 16mm:
4. CONTENT
4.1. Package content:- Unpack the parts listed below and check to ensure they are in
good condition. Any queries must be reported to your dealer immediately.
3 Head Assembly
3 Column with Flange
3 Adjusting Handle with Set Screw (table)
3 Pivoted Clamp Bolts (2 - table arm & bracket)
3 Safety Guard
3 Wedge
3 Chuck and Key
3 Table Arm, Bracket and Worm
3 Screw (upper pulley cover)
GDM120B
GDM160F
16mm
16mm
MT2
MT2
394mm
394mm
162mm
162mm
80mm
80mm
16
210-3340rpm
210-3340rpm
460mm
790mm
640mm
1220mm
Ø310mm
Ø310mm
200 x 185mm
200 x 185mm
420 x 250mm
440 x 260mm
70mm
70mm
60mm
55mm
1000mm
1580mm
350W - 230V
350W - 230V
550W - 230V
550W - 230V
55kg
61kg
GdMX/KC
GdMX/KC
3 Base
3 Feed Handles and Knobs (3)
3 Table
3 Bolts and Washers (4)
3 Arbor
3 Hex. Keys (2)
3 Table Arm, Bracket and Worm
3 Rack and Rack Ring
3 Set Screws (2)
Original Language Version
16
GdM120B
GdM160F
GDM120B, GDM160F
Issue: 4 - 24/02/12