Table of Contents
Advertisement
Figure 18: Bonding practice where hazardous-area equipment cannot meet required standards of insulation from earth
Check that:
a) Barriers are of the types and polarities specified in the safety
documentation.
b) The barriers are attached securely and correctly to the DIN-rail
to make sure the earth connection is safe.
c) There are no apparent signs of damage or corrosion to the
barriers, the ETL7000 earth terminals, the plant earth
connections, and, if fitted, any earth rail assemblies.
d) All hazardous-area and safe-area cable connections are made
correctly and the terminals properly tightened.
e) Interconnecting cables are of the type and rating specified by
the safety documentation and that they are not frayed or
otherwise damaged.
f) All earth returns and cable screens from the hazardous area are
connected to earth either through a barrier, a dummy barrier or
an earth rail.
g) Visually examine the earth conductors and make sure they are
not damaged in any way and that their terminations are secure
and free from corrosion.
h) Using a low-voltage low-current test meter (ie, a meter with an
output not exceeding 3V and 50mA), measure the resistance
between the DIN-rail and the neutral star-point of the supply and
make sure it does not exceed 1Ω. Record the reading and
compare it with readings taken during previous inspections. A
consistent reading repeated over a long period of time is a
reassuring sign indicating a sound earth return which is likely to
remain so. If two earth conductors are used as described in
section 5.3.2, the loop resistance should be measured as
described in that section and the reading should not be greater
than 2Ω.
WARNING: do not try to carry out a high-current earth
resistance test unless it is confirmed by the authority in
charge of the plant that the plant is gas-free.
1.888.610.7664
INM7700-6
Jan 2010
Hazardous area
Hazardous area
Zone 0, 1 or 2
(Zone 2)
or safe area
Hazardous-area
equipment
incapable of
withstanding
insulation test
Bonding conductor
<100m: 4mm
100 200m (maximum): 8mm
www.calcert.com
15
10
20
5
25
0
30
Safe area
Enclosure
DIN-rail
Barriers
2
minimum
2
minimum
Unused cable
cores and
screens
Figure 19: MTL7799 dummy barrier connections
7
FAULT-FINDING
7.1
Introduction
Most barrier-protected systems are relatively simple and their
operation is easy to check. However, when fault finding is necessary,
it must only be undertaken after checking with plant personnel
responsible for safety that it is safe to proceed.
The fault-finding procedures described in this section call for the use
of a digital multimeter – this being the most common type used.
However, other types can be used provided their characteristics when
measuring silicon diodes are known.
Many digital multimeters include a diode test function which is useful
when diode chains are included in the test. These usually operate by
passing 1mA through the diode and measuring the voltage across it.
When measuring more than two diode drops in series, note that the
full-scale range of some multimeters is only 2V on the diode test
range. With three or more diode drops it is therefore possible that the
meter may indicate over-range. In the test tables (tables 4 to 10),
section 8, any drop of more than 4V is indicated as infinity (∞).
Zener diodes and ordinary silicon diodes have a typical forward
voltage drop of approximately 0.6V/diode. Diode return paths with
Schottky diodes have a typical voltage drop of <0.3V for each diode
in the chain, eg, MTL7787+, 7787P+.
Figure 20 depicts a typical switch-status transfer circuit protected by
an MTL7787+ barrier which illustrates some of the fault-finding
techniques discussed in this section. To determine the serviceability of
MTL7700 Series barriers, follow the steps described in sections
7.2 to 7.3.
10
Local
distribution
Safe-area
transformer
equipment
0V
1Ω maximum
Bussed power
1
3
2
4
MTL7799
sales@calcert.com
24Vdc
Advertisement
Table of Contents
