Chamberlain 2280 Owner's Manual
Chamberlain 2280 Owner's Manual

Chamberlain 2280 Owner's Manual

Chamberlain garage door opener 2280 owner's manual
Hide thumbs Also See for 2280:
Table of Contents

Advertisement

GARAGE DOOR OPENER
For Residential Use Only
Owner's Manual
I
I
I
I
I

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 2280 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Chamberlain 2280

  • Page 1 GARAGE DOOR OPENER For Residential Use Only Owner’s Manual...
  • Page 2: Table Of Contents

    TABLE OF CONTENTS Introduction Assembly Installation INTRODUCTION Safety Symbol and Signal Word Review Pages 2-5 Adjustment Operation Pages 6-7 Pages 7-23 Programming Repair Parts Accessories Repair Parts and Service Warranty Pages 24-26 Pages 27-30 Pages 31-32 Pages 33-34 serious injury or death...
  • Page 3 Preparing your garage door Tools needed...
  • Page 4 Planning...
  • Page 5 Carton Inventory ✚...
  • Page 6: Assembly

    ASSEMBLY STEP 1 Attach the T-Rail to the Motor Unit ASSEMBLY STEP 2 Set the Belt Tension...
  • Page 7: Installation

    ASSEMBLY STEP 3 Attach the Belt Cap Retainer You have now finished assembling your garage door opener. Please read the following warnings before proceeding to the installation section. INSTALLATION...
  • Page 8 INSTALLATION STEP 1 Determine the Header Bracket Location Proceed to Step 2, page 10.
  • Page 9 NOTE: If the total number of inches exceeds the height available in your garage, use the maximum height possible, or refer to page 10 for ceiling installation. Proceed to Step 2, page 10.
  • Page 10 INSTALLATION STEP 2 Install the Header Bracket...
  • Page 11 INSTALLATION STEP 3 Attach the T-Rail to the Header Bracket NOTE:...
  • Page 12 INSTALLATION STEP 4 Position the Opener...
  • Page 13 INSTALLATION STEP 5 Hang the Opener...
  • Page 14 INSTALLATION STEP 6 Install the Door Control NOTE: NOTE: (Standard installation only) RED WHT NOTE:...
  • Page 15 INSTALLATION STEP 7 Install the Lights NOTE: INSTALLATION STEP 8 Attach the Emergency Release Rope and Handle NOTE:...
  • Page 16 INSTALLATION STEP 9 Electrical Requirements...
  • Page 17 INSTALLATION STEP 10 Install The Protector System ®...
  • Page 18 Garage door track installation (preferred): Wall installation: Floor installation:...
  • Page 19 NOTE:...
  • Page 20 INSTALLATION STEP 11 Fasten the Door Bracket NOTE: Metal or light weight doors using a vertical angle iron brace between the door panel support and the door bracket: Metal, insulated or light weight factory reinforced doors: Wood Doors: NOTE:...
  • Page 22 INSTALLATION STEP 12 Connect Door Arm to Trolley...
  • Page 24: Adjustment

    ADJUSTMENT STEP 1 Adjust the UP and DOWN Travel Limits...
  • Page 25 ADJUSTMENT STEP 2 Adjust the Force...
  • Page 26 ADJUSTMENT STEP 3 Test the Safety Reversal System ADJUSTMENT STEP 4 Test the Protector System ®...
  • Page 27: Operation

    OPERATION Using Your Garage Door Opener ✚ ✚ ✚ ✚...
  • Page 28 Using the Wall-Mounted Door Control To Open the Door Manually...
  • Page 29 CARE OF YOUR OPENER Having a Problem?
  • Page 30 Having a Problem? (Continued)
  • Page 31: Programming

    PROGRAMMING To Add an Additional Hand-held Remote Control To Erase All Codes From Motor Unit Memory *3-Channel Remotes ✚ ✚ ✚...
  • Page 32 To Add or Change a Keyless Entry PIN NOTE: Your new Keyless Entry must be programmed to operate your garage door opener. To change an existing, known PIN To set a temporary PIN close ✽ NOTE: This method requires two people if the Keyless Entry is already mounted outside the garage.
  • Page 33: Repair Parts

    REPAIR PARTS Rail Assembly Parts Installation Parts...
  • Page 34 Motor Unit Assembly Parts LIMIT SWITCH ASSY.
  • Page 35: Accessories

    ACCESSORIES ✚ ✚ ✚ ✚...

This manual is also suitable for:

Liftmaster security+ 2280 1/2 hp

Table of Contents

Save PDF