S2_brotherE_Cover2.fm Page A Tuesday, March 30, 2004 1:36 PM Enclosed Accessories After opening the box, check that the following accessories are enclosed. If any item is missing or damaged, contact your retailer. Accessories Note (For U.S.A. only) ● Foot controller: Model N5V This foot controller can be used on this machine model CS-8060/CS-80.
S2_brotherE.book Page B Thursday, February 13, 2003 11:03 AM Names of Machine Parts and Their Functions The names of the various parts of the sewing machine and their functions are described below. Before using the sewing machine, carefully read these descriptions to learn the names of the machine parts. Front view 1 Thread cassette compartment cover 9 Operation buttons...
S2_brotherE.book Page C Thursday, February 13, 2003 11:03 AM ———————————————————————————————————————— Names of Machine Parts and Their Functions Right-side/rear view Needle and presser foot section 1 Buttonhole lever 1 Handle Lower the buttonhole lever when sewing buttonholes Carry the sewing machine by its handle when and bar tacks.
S2_brotherE.book Page D Thursday, February 13, 2003 11:03 AM Operation buttons The operation buttons help you to easily perform various basic sewing machine operations. 1 Thread cassette indicator 6 Reverse/reinforcement stitch button The indicator lights up or goes off depending on the Press the reverse/reinforcement stitch button to sew condition of the sewing machine.
S2_brotherE.book Page E Thursday, February 13, 2003 11:03 AM ———————————————————————————————————————— Names of Machine Parts and Their Functions Operation panel The operation panel, located on the front of the sewing machine, consists of various buttons and sliders for specifying how the stitch will be sewn. 1 Stitches There are 50 stitches.
S2_brotherE.book Page 1 Thursday, February 13, 2003 11:03 AM Optional Accessories The following are available as optional accessories. 1. Side cutter Part code: SA177, XC3879-002 2. Quilting guide Part code: SA132, XC2215-002 3. Guide foot Part code: SA133, XC1957-002 4. Walking foot Part code: SA140, XC2214-002 5.
S2_brotherE.book Page 2 Thursday, February 13, 2003 11:03 AM Introduction Thank you for purchasing this sewing machine. Before using this sewing machine, carefully read the “Important Safety Instructions” (page 6), and then study this manual for the correct operation of the various functions. In addition, after you have finished reading this manual, store it where it can quickly be accessed for future reference.
S2_brotherE.book Page 3 Thursday, February 13, 2003 11:03 AM Contents Enclosed Accessories ....................Cover A Accessories .............................Cover A Names of Machine Parts and Their Functions ............Cover B Front view ...............................Cover B Needle and presser foot section ......................Cover C Right-side/rear view ..........................Cover C Operation buttons ..........................
Page 10
S2_brotherE.book Page 4 Thursday, February 13, 2003 11:03 AM ——————————————————————————————————————————————————————————————— SEWING BASICS .....................41 Sewing ..........................42 General sewing procedure ..........................43 Positioning the fabric ............................44 Starting to sew ..............................45 Securing the stitching ............................47 Cutting the thread ............................49 Adjusting the Thread Tension ....................50 Changing the tension of the upper thread ......................
Page 11
S2_brotherE.book Page 5 Thursday, February 13, 2003 11:03 AM APPENDIX .......................95 Stitch Settings ........................96 Utility stitches ..............................96 Maintenance ........................100 Cleaning the machine surface ........................100 Cleaning the shuttle ............................100 Troubleshooting ......................102 Error messages .........................106 Operation beep ............................. 106 Changing the needle stop position ...................107 Index ..........................108...
S2_brotherE.book Page 6 Thursday, February 13, 2003 11:03 AM Important Safety Instructions When using this machine, basic safety precautions should always be taken, including the following: Read all instructions before using. DANGER To reduce the risk of electric shock: 1. The machine should never be left unattended while plugged in. Always unplug the machine from the electrical outlet immediately after using and before cleaning.
Page 13
S2_brotherE.book Page 7 Thursday, February 13, 2003 11:03 AM FOR USERS IN THE UK, EIRE, MALTA AND CYPRUS ONLY If this machine is fitted with a three-pin non-rewireable BS plug then please read the following. IMPORTANT If the available socket outlet is not suitable for the plug supplied with this equipment, it should be cut off and an appropriate three-pin plug fitted.
Page 14
In the event a malfunction occurs or adjustment is required, first follow the troubleshooting table in the back of the operation manual to inspect and adjust the machine yourself. If the problem persists, please consult your local authorized Brother dealer. For additional product information and updates, visit our web site at www.brother.com...
S2_brotherE.book Page 9 Thursday, February 13, 2003 11:03 AM GETTING READY The various preparations required before starting to sew are described in this chapter. Turning the Machine On/Off .................10 Winding/Installing the Bobbin ................12 Upper Threading ....................18 Replacing the Needle .....................30 Replacing the Presser Foot ..................35 Sewing Cylindrical Pieces ..................40...
S2_brotherE.book Page 10 Thursday, February 13, 2003 11:03 AM GETTING READY ———————————————————————————————————————————————————————— Turning the Machine On/Off This section explains how to turn the sewing machine on and off. Power supply precautions Be sure to observe the following precautions concerning the power supply. WARNING Use only regular household electricity for the power source.
S2_brotherE.book Page 11 Thursday, February 13, 2003 11:03 AM Turning on the machine Turning off the machine When you are finished using the sewing machine, Make sure that the sewing machine is turned turn it off. In addition, before transporting the sewing off (the main power switch is set to “O”), and machine to another location, be sure to turn it off.
S2_brotherE.book Page 12 Thursday, February 13, 2003 11:03 AM GETTING READY ———————————————————————————————————————————————————————— Winding/Installing the Bobbin This section describes how to wind the thread onto the bobbin, and then insert the bobbin thread. Bobbin precautions Be sure to observe the following precautions concerning the bobbin. CAUTION Only use the bobbin (part code: SA156, XA5539-151) designed specifically for this sewing machine.
Page 19
S2_brotherE.book Page 13 Thursday, February 13, 2003 11:03 AM Slide the bobbin winder shaft to the right. CAUTION Two spool cap sizes are available, allowing you to choose a spool cap that best fits the size of spool being used. If the spool cap is too small for the spool being used, the thread may catch on the slit in the spool or the needle may break.
Page 20
S2_brotherE.book Page 14 Thursday, February 13, 2003 11:03 AM GETTING READY ———————————————————————————————————————————————————————— While using your left hand to hold the end of Memo the thread that wraps around the thread guide G When using thread that winds off quickly, for bobbin winding, use your right hand to wind the free end of the thread clockwise such as transparent nylon thread or metallic thread, place the enclosed spool net over...
Page 21
S2_brotherE.book Page 15 Thursday, February 13, 2003 11:03 AM Slide the sewing speed controller to the right Slide the bobbin winder shaft to the left. (so that the speed will be fast). Remove the bobbin from the shaft. 1 Sewing speed controller Press (start/stop button) once.
S2_brotherE.book Page 16 Thursday, February 13, 2003 11:03 AM GETTING READY ———————————————————————————————————————————————————————— Remove the bobbin cover. Installing the bobbin Hold the bobbin with your right hand and Install the bobbin wound with thread. hold the end of the thread with your left. CAUTION Use a bobbin thread that has been correctly wound, otherwise the needle...
Page 23
S2_brotherE.book Page 17 Thursday, February 13, 2003 11:03 AM Reattach the bobbin cover. Insert the tab in the lower-left corner of the bobbin cover, and then lightly press down on the right side. The lower threading is finished. Next, thread the upper thread. Continue with the procedure in “Upper Threading”...
S2_brotherE.book Page 18 Thursday, February 13, 2003 11:03 AM GETTING READY ———————————————————————————————————————————————————————— Upper Threading In this section, the procedures for positioning the spool for the upper thread and threading the needle are described. CAUTION When threading the upper thread, carefully follow the instructions. If the upper threading is not correct, the thread may become tangled or the needle may bend or break.
S2_brotherE.book Page 19 Thursday, February 13, 2003 11:03 AM CAUTION Loading the spool into the thread cassette Two spool cap sizes are available, allowing you to choose a spool cap that Load the spool of thread into the enclosed thread best fits the size of spool being used.
Page 26
S2_brotherE.book Page 20 Thursday, February 13, 2003 11:03 AM GETTING READY ———————————————————————————————————————————————————————— Push the thread cassette eject lever on the left Place the spool for the upper thread onto the side of the machine toward the back. spool pin. Slide the spool onto the spool pin so that the thread unwinds from the left, as seen from the top.
Page 27
S2_brotherE.book Page 21 Thursday, February 13, 2003 11:03 AM While holding the end of the thread with your • When using special thread such as metallic right hand and the thread cassette with your thread, use the thumb of your left hand to left hand, close the cover.
S2_brotherE.book Page 22 Thursday, February 13, 2003 11:03 AM GETTING READY ———————————————————————————————————————————————————————— Pull the thread under the disc at the front in Threading the needle the lower-left corner and around to the right, and then cut the thread with the cutter. In this section, the procedures for installing the Follow arrow 6 indicated on the thread thread cassette and threading the needle are...
Page 29
S2_brotherE.book Page 23 Thursday, February 13, 2003 11:03 AM • If the needle is not raised to the correct position, the needle cannot be threaded with the needle threader. Be sure to check that the thread cassette indicator is lit up in green before inserting the thread cassette.
S2_brotherE.book Page 24 Thursday, February 13, 2003 11:03 AM GETTING READY ———————————————————————————————————————————————————————— Close the thread cassette compartment cover. Using the extra spool pin When using spools with a size that cannot be loaded into the thread cassette, use the enclosed extra spool pin.
S2_brotherE.book Page 25 Thursday, February 13, 2003 11:03 AM Thread the thread cassette with the thread from the spool on the extra spool pin. Thread the needle manually (without using the needle threader) When using special thread, thread with a thickness of 130/20 or less, the wing needle or the twin needle which cannot be used with the needle threader, thread the needle as described below.
S2_brotherE.book Page 26 Thursday, February 13, 2003 11:03 AM GETTING READY ———————————————————————————————————————————————————————— Load the spool for the second thread color Using the twin needle onto the extra spool pin. Using the twin needle, you can sew two parallel lines of the same stitch with two different colors. Both upper threads should have the same thickness and quality.
Page 33
S2_brotherE.book Page 27 Thursday, February 13, 2003 11:03 AM Insert the thread cassette (with the extra spool Remove the thread for the right side of the pin attached) into the thread cassette stitch from the needle bar thread hook, and compartment.
Page 34
S2_brotherE.book Page 28 Thursday, February 13, 2003 11:03 AM GETTING READY ———————————————————————————————————————————————————————— Start sewing. • For details on starting to sew, refer to “ Starting to sew” (page 45). Two lines of stitching are sewn parallel to each other. Note G When changing the sewing direction, press (needle position button) to raise the needle from the fabric, and then raise the...
S2_brotherE.book Page 29 Thursday, February 13, 2003 11:03 AM Pull out about 10-15 cm (3/8-5/8 inch) of the Pulling up the bobbin thread bobbin thread under the presser foot toward the rear of the machine. When making gathers or before free-motion quilting, first pull up the bobbin thread as described below.
S2_brotherE.book Page 30 Thursday, February 13, 2003 11:03 AM GETTING READY ———————————————————————————————————————————————————————— Replacing the Needle This section provides information on sewing machine needles. Needle precautions Be sure to observe the following precautions concerning the handling of the needle. Failure to observe these precautions is extremely dangerous, for example, if the needle breaks and fragments are dispersed.
S2_brotherE.book Page 31 Thursday, February 13, 2003 11:03 AM Memo Checking the needle G The smaller the thread number, the thicker Sewing with a bent needle is extremely dangerous the thread, and the larger the needle since the needle may break while the machine is number, the thicker the needle.
S2_brotherE.book Page 32 Thursday, February 13, 2003 11:03 AM GETTING READY ———————————————————————————————————————————————————————— Hold the needle with your left hand, and then Replacing the needle use a screwdriver to turn the needle clamp screw counterclockwise to remove the Replace the needle as described below. Use the needle.
Page 39
S2_brotherE.book Page 33 Thursday, February 13, 2003 11:03 AM I Using the needle-changing tool While holding the needle with your left hand, use the screwdriver to tighten the needle Use the enclosed needle-changing tool to replace clamp screw. the needle as described below. Install the twin needle in the same way.
Page 40
S2_brotherE.book Page 34 Thursday, February 13, 2003 11:03 AM GETTING READY ———————————————————————————————————————————————————————— Lower the needle-changing tool. Insert the needle until it touches the needle stopper, and then use the screwdriver to tighten the needle clamp screw. The needle can be removed from the needle bar.
S2_brotherE.book Page 35 Thursday, February 13, 2003 11:03 AM Replacing the Presser Foot The presser foot presses down on the fabric. Presser foot precautions Be sure to observe the following precautions concerning the presser feet. CAUTION Use the presser foot appropriate for the type of stitch that you wish to sew, otherwise the needle may hit the presser foot, causing the needle to bend or break.
Page 42
S2_brotherE.book Page 36 Thursday, February 13, 2003 11:03 AM GETTING READY ———————————————————————————————————————————————————————— Press the black button at the back of the Raise the presser foot lever to check that the presser foot holder. presser foot is securely attached. 1 Black button 2 Presser foot holder The presser foot holder releases the presser Note...
S2_brotherE.book Page 37 Thursday, February 13, 2003 11:03 AM Hold the presser foot holder in place with Removing the presser foot your right hand, and then tighten the screw using the screwdriver in your left hand. holder Remove the presser foot holder when cleaning the sewing machine or when installing a presser foot that does not use the presser foot holder, such as the quilting foot.
S2_brotherE.book Page 38 Thursday, February 13, 2003 11:03 AM GETTING READY ———————————————————————————————————————————————————————— CAUTION Using the optional walking foot Be sure to securely tighten the screw with the screwdriver, otherwise the With the walking foot, both pieces of fabric are fed needle may touch the presser foot, evenly by the feed dogs and the teeth on the presser causing it to bend or break.
Page 45
S2_brotherE.book Page 39 Thursday, February 13, 2003 11:03 AM Raise the presser foot lever. 1 Presser foot lever The presser foot is raised. With a screwdriver, loosen the presser foot holder screw, and then remove the walking foot. 1 Presser foot holder screw Attach the presser foot holder.
S2_brotherE.book Page 40 Thursday, February 13, 2003 11:03 AM GETTING READY ———————————————————————————————————————————————————————— Sewing Cylindrical Pieces Free-arm sewing makes sewing cylindrical pieces easy. Then, install the flap back to its original Free-arm sewing position. Removing the flap allows for free-arm sewing, making it easier to sew cylindrical pieces such as sleeve cuffs and pant legs.
S2_brotherE.book Page 41 Thursday, February 13, 2003 11:03 AM SEWING BASICS The necessary preparations for sewing are described in this chapter. Sewing ........................42 Adjusting the Thread Tension .................50 Adjusting the Stitch Width and Length ..............51 Useful Sewing Tips ....................53...
S2_brotherE.book Page 42 Thursday, February 13, 2003 11:03 AM SEWING BASICS ———————————————————————————————————————————————————————— Sewing Basic sewing operations are described below. Before operating the sewing machine, read the following precautions. CAUTION While the machine is in operation, pay special attention to the needle location. In addition, keep your hands away from all moving parts such as the needle and balance wheel, otherwise injuries may occur.
S2_brotherE.book Page 43 Thursday, February 13, 2003 11:03 AM General sewing procedure Follow the basic procedures below to sew. Turn on the sewing machine. Turn on the For details on turning on the machine, refer to “ Turning on the machine” machine.
S2_brotherE.book Page 44 Thursday, February 13, 2003 11:03 AM SEWING BASICS ———————————————————————————————————————————————————————— Positioning the fabric Be sure that the fabric pieces are sewn in the correct order and that the right and wrong sides of the fabric are aligned correctly. Turn on the sewing machine.
S2_brotherE_chapt2.fm Page 45 Tuesday, March 30, 2004 2:32 PM When the end of the stitching is reached, Starting to sew press (start/stop button) once. The machine stops sewing with the needle Once you are ready to start sewing, you can start the down (in the fabric).
Page 52
S2_brotherE.book Page 46 Thursday, February 13, 2003 11:03 AM SEWING BASICS ———————————————————————————————————————————————————————— Turn on the sewing machine. When you are finished sewing, raise the needle, and then cut the threads. • For details, refer to “ Cutting the thread” (page 49). Memo G When the foot controller is plugged in, the start/stop button cannot be used to start or...
S2_brotherE.book Page 47 Thursday, February 13, 2003 11:03 AM After sewing 3 to 5 stitches, press Securing the stitching (reverse/reinforcement stitch button). Keep the reverse/reinforcement stitch button When sewing with the straight stitch, for example, at held down until you reach the beginning of the the end of an opening or where seams do not stitching.
Page 54
S2_brotherE.book Page 48 Thursday, February 13, 2003 11:03 AM SEWING BASICS ———————————————————————————————————————————————————————— I Sewing reinforcement stitches After 3 to 5 reverse stitches have been sewn, release (reverse/reinforcement stitch When sewing stitches other than straight or zigzag button). stitches that are secured with reverse stitching, pressing (reverse/reinforcement stitch The machine stops sewing.
S2_brotherE.book Page 49 Thursday, February 13, 2003 11:03 AM I Using the thread cutter button Cutting the thread (Only for models equipped with the thread cutter button) When you have finished sewing, cut the threads. When using a model equipped with a thread cutter button, the thread can easily be cut if the When you wish to finish the stitching and the button is pressed.
S2_brotherE.book Page 50 Thursday, February 13, 2003 11:03 AM SEWING BASICS ———————————————————————————————————————————————————————— Adjusting the Thread Tension The tensions of the upper thread and of the bobbin thread (thread tension) should be adjusted so that they are equal. Turn the thread tension dial downward to loosen Changing the tension of the the upper thread.
S2_brotherE.book Page 51 Thursday, February 13, 2003 11:03 AM Adjusting the Stitch Width and Length The zigzag width (pattern width) and stitch length of utility stitches can be adjusted. Normally, when a stitch is selected, the appropriate width and length are automatically selected. For details on the range of values within which the width and length can be set, refer to “...
S2_brotherE.book Page 52 Thursday, February 13, 2003 11:03 AM SEWING BASICS ———————————————————————————————————————————————————————— Adjusting the stitch length Press the stitch length adjustment button in the operation panel. The stitch length adjustment indicator lights Slide the stitch length adjustment slider to the left or right.
S2_brotherE.book Page 53 Thursday, February 13, 2003 11:03 AM Useful Sewing Tips Various ways to achieve better results for your sewing projects are described below. Refer to these tips when sewing your project. Trial sewing Sewing curves After you have set up the machine with the thread Stop sewing, and then slightly change the sewing and needle appropriate for the type of fabric being direction to sew around the curve.
S2_brotherE.book Page 54 Thursday, February 13, 2003 11:03 AM SEWING BASICS ———————————————————————————————————————————————————————— CAUTION Sewing thick fabrics If fabric more than 6 mm (15/64 inch) I If the fabric does not fit under the presser foot thick is sewn or if the fabric is pushed If the fabric does not fit easily under the presser with too much force, the needle may foot, raise the presser foot lever even higher to...
S2_brotherE.book Page 55 Thursday, February 13, 2003 11:03 AM Sewing thin fabrics Sewing an even seam allowance When sewing thin fabrics, the stitching may become misaligned or the fabric may not feed correctly. If To sew an even seam, start sewing so that the seam this occurs, place thin paper or stabilizer material allowance is to the right of the presser foot, and the under the fabric and sew it together with the fabric.
Page 62
S2_brotherE.book Page 56 Thursday, February 13, 2003 11:03 AM SEWING BASICS ————————————————————————————————————————————————————————...
S2_brotherE.book Page 57 Thursday, February 13, 2003 11:03 AM UTILITY STITCHES The various stitches and their applications are described in this chapter. Selecting Stitching ....................58 Overcasting Stitches ....................60 Basic Stitching ......................64 Blind Hem Stitching ....................65 Buttonhole Stitching ....................67 Zipper Insertion .....................73 Sewing Stretch Fabrics and Elastic Tape ..............77 Appliqué, Patchwork and Quilt Stitching ...............79 Reinforcement Stitching ..................85...
S2_brotherE.book Page 58 Thursday, February 13, 2003 11:03 AM UTILITY STITCHES ——————————————————————————————————————————————————————— Selecting Stitching You can select any of the various types of stitching available. Press (stitch selection key). The Selecting stitching number of the selected stitch is displayed. Each press of increases the number by Using the operation panel keys, select the desired stitch.
Page 65
S2_brotherE.book Page 59 Thursday, February 13, 2003 11:03 AM To adjust the stitch width, slide the stitch width adjustment slider to the left or right. Press the stitch width adjustment button, and then slide the stitch width adjustment slider to adjust the stitch width.
S2_brotherE.book Page 60 Thursday, February 13, 2003 11:03 AM UTILITY STITCHES ——————————————————————————————————————————————————————— Overcasting Stitches Sew overcasting stitches along the edges of cut fabric to prevent them from fraying. Seven stitches are available for overcasting. The procedure for sewing overcasting stitch is explained according to the presser foot that is used. Sewing overcasting stitches using overcasting foot “G”...
S2_brotherE.book Page 61 Thursday, February 13, 2003 11:03 AM Sewing overcasting stitches using zigzag foot “J” Three stitches can be used to sew overcasting stitches with zigzag foot “ J” . Stitch Width Stitch Length Presser [mm (inch.)] [mm (inch.)] Stitch Name Application Pattern...
S2_brotherE.book Page 62 Thursday, February 13, 2003 11:03 AM UTILITY STITCHES ——————————————————————————————————————————————————————— Sewing overcasting stitches using the optional side cutter Using the side cutter, seam allowances can be finished while the edge of the fabric is cut off. The following four stitches can be used to sew overcasting.
Page 69
S2_brotherE.book Page 63 Thursday, February 13, 2003 11:03 AM Raise the presser foot lever to check that the Position the fabric in the side cutter. side cutter is securely attached. The cut in the fabric should be positioned over the guide plate of the side cutter. CAUTION If the thread cassette is to be installed with the side cutter attached, be sure to...
S2_brotherE.book Page 64 Thursday, February 13, 2003 11:03 AM UTILITY STITCHES ——————————————————————————————————————————————————————— Basic Stitching Straight stitches are used for sewing plain seams. Three stitches are available for basic stitching. Stitch Width Stitch Length Presser [mm (inch.)] [mm (inch.)] Stitch Name Application Pattern Foot...
S2_brotherE.book Page 65 Thursday, February 13, 2003 11:03 AM Blind Hem Stitching Secure the bottoms of skirts and pants with a blind hem. Two stitches are available for blind hem stitching. Stitch Width Stitch Length Presser [mm (inch.)] [mm (inch.)] Stitch Name Application Pattern...
Page 72
S2_brotherE.book Page 66 Thursday, February 13, 2003 11:03 AM UTILITY STITCHES ——————————————————————————————————————————————————————— I If the needle does not catch the hem fold Adjust the stitch width until the needle slightly catches the fold of the hem. If the needle does not catch enough of the hem fold, move the stitch width adjustment lever to the right.
S2_brotherE.book Page 67 Thursday, February 13, 2003 11:03 AM Buttonhole Stitching Buttonholes can be sewn and buttons can be sewn on. Five stitches are available for sewing one-step buttonholes. Stitch Width Stitch Length Presser [mm (inch.)] [mm (inch.)] Stitch Name Application Pattern Foot...
S2_brotherE.book Page 68 Thursday, February 13, 2003 11:03 AM UTILITY STITCHES ——————————————————————————————————————————————————————— Buttonhole sewing The maximum buttonhole length is about 28 mm (1-1/8 inch) (diameter + thickness of the button). Buttonholes are sewn from the front of the presser foot to the back, as shown below. 1 Reinforcement stitching The names of parts of buttonhole foot “...
Page 75
S2_brotherE.book Page 69 Thursday, February 13, 2003 11:03 AM I If the button does not fit in the button guide Pass the upper thread down through the hole plate in the presser foot. Add together the diameter and thickness of •...
Page 76
S2_brotherE.book Page 70 Thursday, February 13, 2003 11:03 AM UTILITY STITCHES ——————————————————————————————————————————————————————— Raise the presser foot lever, remove the CAUTION fabric, and cut the thread. When opening the buttonhole with the Raise the buttonhole lever to its original seam ripper, do not place your hands in position.
S2_brotherE.book Page 71 Thursday, February 13, 2003 11:03 AM I Sewing buttonholes on stretch fabrics Button sewing When sewing buttonholes on stretch fabrics, use a gimp thread. Buttons can be sewn on with the sewing machine. Buttons with 2 or with 4 holes can be attached. Hook the gimp thread onto the part of buttonhole foot “A”...
Page 78
S2_brotherE.book Page 72 Thursday, February 13, 2003 11:03 AM UTILITY STITCHES ——————————————————————————————————————————————————————— Place the button into button-sewing foot “M”. CAUTION When sewing, be sure that the needle does not touch the button, otherwise the needle may bend or break. Start sewing. •...
S2_brotherE.book Page 73 Thursday, February 13, 2003 11:03 AM Zipper Insertion A zipper can be sewn in place. Stitch Width Stitch Length Presser [mm (inch.)] [mm (inch.)] Stitch Name Application Pattern Foot Auto Manual Auto Manual Straight stitch (center Attaching zippers 0.2–...
S2_brotherE.book Page 74 Thursday, February 13, 2003 11:03 AM UTILITY STITCHES ——————————————————————————————————————————————————————— Select stitch Inserting a side zipper • For details, refer to “ Selecting stitching” Stitching is sewn on only one piece of fabric. Use (page 58). this type of zipper for side openings and back openings.
Page 81
S2_brotherE.book Page 75 Thursday, February 13, 2003 11:03 AM Press the seam allowance so that the right side CAUTION (the side that will not be stitched) has an extra 3 mm (1/8 inch). When using zipper foot “I”, be sure to select the straight stitch (center needle position), and slowly turn the balance wheel toward you to check that the...
Page 82
S2_brotherE.book Page 76 Thursday, February 13, 2003 11:03 AM UTILITY STITCHES ——————————————————————————————————————————————————————— Close the zipper, turn over the fabric, and When you are about 5 cm (2 inch) from the then baste the other side of the zipper to the end of the zipper, stop the sewing machine fabric.
S2_brotherE.book Page 77 Thursday, February 13, 2003 11:03 AM Sewing Stretch Fabrics and Elastic Tape Stretch fabrics can be sewn and elastic tape can be attached. Stitch Width Stitch Length Presser [mm (inch.)] [mm (inch.)] Stitch Name Application Pattern Foot Auto Manual Auto...
Page 84
S2_brotherE.book Page 78 Thursday, February 13, 2003 11:03 AM UTILITY STITCHES ——————————————————————————————————————————————————————— Select stitch • For details, refer to “ Selecting stitching” (page 58). Sew the elastic tape to the fabric while stretching the tape so that it is the same length as the fabric.
S2_brotherE.book Page 79 Thursday, February 13, 2003 11:03 AM Appliqué, Patchwork and Quilt Stitching The stitches that can be used for sewing appliqués, patchwork and quilts are described below. Stitch Width Stitch Length Presser [mm (inch.)] [mm (inch.)] Stitch Name Application Pattern Foot...
S2_brotherE.book Page 80 Thursday, February 13, 2003 11:03 AM UTILITY STITCHES ——————————————————————————————————————————————————————— Select a stitch. Appliqué stitching • For details, refer to “ Selecting stitching” (page 58). Cut out the appliqué, leaving a seam Turn the balance wheel toward you, and then allowance of between 3 and 5 mm begin sewing around the edge of the appliqué, (1/8 and 3/16 inch).
S2_brotherE.book Page 81 Thursday, February 13, 2003 11:03 AM Piecing Patchwork (crazy quilt) stitching Sewing together two pieces of fabric is called “ piecing” . The fabric pieces should be cut with a Fold the edge of the top piece of fabric and 6.5 mm (1/4 inch) seam allowance.
S2_brotherE.book Page 82 Thursday, February 13, 2003 11:03 AM UTILITY STITCHES ——————————————————————————————————————————————————————— Memo Quilting G To change the width of the seam allowance Sandwiching batting between the top and bottom (the needle position), adjust the stitch width. layers of fabric is called “ quilting” . Quilts can easily be sewn using the optional walking foot and the optional quilting guide.
S2_brotherE.book Page 83 Thursday, February 13, 2003 11:03 AM I Using the optional quilting guide Free-motion quilting Use the quilting guide to sew parallel stitches that are equally spaced. With free-motion quilting, the feed dogs can be lowered (using the drop feed lever) so that the fabric can be moved freely in any direction.
Page 90
S2_brotherE.book Page 84 Thursday, February 13, 2003 11:03 AM UTILITY STITCHES ——————————————————————————————————————————————————————— Slide the drop feed lever, located at the rear After sewing is finished, slide the drop feed of the machine on the base, to (to the lever to (to the left as seen from the right as seen from the front of the machine).
S2_brotherE.book Page 85 Thursday, February 13, 2003 11:03 AM Reinforcement Stitching Reinforce points that will be subject to strain, such as sleeve holes, inseams and pocket corners. Stitch Width Stitch Length Presser [mm (inch.)] [mm (inch.)] Stitch Name Application Pattern Foot Auto Manual...
Page 92
S2_brotherE.book Page 86 Thursday, February 13, 2003 11:03 AM UTILITY STITCHES ——————————————————————————————————————————————————————— Attach buttonhole foot “A”. The buttonhole lever is positioned behind the • For details, refer to “ Replacing the presser bracket on the buttonhole foot. foot” (page 35). Select stitch •...
S2_brotherE.book Page 87 Thursday, February 13, 2003 11:03 AM Eyelet Stitching Eyelets, such as those on belts, can be sewn. Three sizes of eyelets are possible: 7 mm, 6 mm and 5 mm (1/4, 15/64 and 3/16 inch). Stitch Width Stitch Length Presser [mm (inch.)]...
S2_brotherE.book Page 88 Thursday, February 13, 2003 11:03 AM UTILITY STITCHES ——————————————————————————————————————————————————————— Decorative Stitching Various decorative stitches can be sewn with this sewing machine. Stitch Width Stitch Length Presser [mm (inch.)] [mm (inch.)] Stitch Name Application Pattern Foot Auto Manual Auto Manual 0.0–...
S2_brotherE.book Page 89 Thursday, February 13, 2003 11:03 AM Sew with the center of the presser foot Fagoting aligned along the center of the two pieces of fabric. Stitching across an open seam is called “ fagoting” . It is used on blouses and children's clothing. This stitch is more decorative when thicker thread is used.
S2_brotherE.book Page 90 Thursday, February 13, 2003 11:03 AM UTILITY STITCHES ——————————————————————————————————————————————————————— Scallop stitching Smocking The wave-shaped repeating pattern that looks like The decorative stitch created by stitching or shells is called “ scalloping” . It is used on the collars embroidering over gathers is called “...
S2_brotherE.book Page 91 Thursday, February 13, 2003 11:03 AM Joining Select stitch • For details, refer to “ Selecting stitching” Decorative bridging stitches can be sewn over the (page 58). seam allowance of joined fabrics. This is used when making a crazy quilt. Stitch between the straight stitches.
S2_brotherE.book Page 92 Thursday, February 13, 2003 11:03 AM UTILITY STITCHES ——————————————————————————————————————————————————————— Start sewing. Heirloom stitching When sewing with the wing needle, the needle holes are enlarged, creating a lace-like decorative stitch. This is used to decorate hems and tablecloths on thin or mediumweight fabrics in addition to plain weave fabrics.
Page 99
S2_brotherE.book Page 93 Thursday, February 13, 2003 11:03 AM I Drawnwork (Example 2) Attach monogramming foot “N”. • For details, refer to “ Replacing the presser foot” (page 35). Select stitch Pull out several threads from two sections of the fabric, separated by an unfrayed section of •...
Page 100
S2_brotherE.book Page 94 Thursday, February 13, 2003 11:03 AM UTILITY STITCHES ———————————————————————————————————————————————————————...
S2_brotherE.book Page 95 Thursday, February 13, 2003 11:03 AM APPENDIX The various maintenance and troubleshooting procedures are described in this chapter. Stitch Settings ......................96 Maintenance ......................100 Troubleshooting ....................102 Error messages .....................106 Changing the needle stop position ...............107 Index ........................108...
S2_brotherE.book Page 96 Thursday, February 13, 2003 11:03 AM APPENDIX —————————————————————————————————————————————————————————— Stitch Settings Applications, stitch lengths and widths and whether the twin needle can be used are listed for utility stitches in the following table. Utility stitches Stitch Width Stitch Length [mm (inch.)] [mm (inch.)] Stitch Name...
Page 103
S2_brotherE.book Page 97 Thursday, February 13, 2003 11:03 AM Stitch Width Stitch Length [mm (inch.)] [mm (inch.)] Stitch Name Pattern Application Auto Manual Auto Manual Patchwork stitching 0.0– 7.0 0.2– 4.0 Reinforce- and decorative stitching (3/16) (0– 1/4) (1/16) (1/64– 3/16) ment Patchwork stitching, decorative stitching and...
Page 104
S2_brotherE.book Page 98 Thursday, February 13, 2003 11:03 AM APPENDIX —————————————————————————————————————————————————————————— Stitch Width Stitch Length [mm (inch.)] [mm (inch.)] Stitch Name Pattern Application Auto Manual Auto Manual Horizontal buttonholes Automatic 3.0– 5.0 0.2– 1.0 on thin and medium- reinforce- (3/16) (1/8–...
Page 105
S2_brotherE.book Page 99 Thursday, February 13, 2003 11:03 AM Stitch Width Stitch Length [mm (inch.)] [mm (inch.)] Stitch Name Pattern Application Auto Manual Auto Manual 0.0– 7.0 0.2– 4.0 Reinforce- For decoration, etc. (1/4) (0– 1/4) (3/32) (1/64– 3/16) ment 0.0–...
S2_brotherE.book Page 100 Thursday, February 13, 2003 11:03 AM APPENDIX —————————————————————————————————————————————————————————— Maintenance Simple sewing machine maintenance operations are described below. Cleaning the shuttle Cleaning the machine surface Sewing performance will suffer if dust collects in the shuttle; therefore, it should be cleaned periodically. If the surface of the machine is dirty, lightly soak a cloth in neutral detergent, squeeze it out firmly, and Turn off the sewing machine.
Page 107
S2_brotherE.book Page 101 Thursday, February 13, 2003 11:03 AM Turn the balance wheel toward you until the Check that the edge of the race shelf is tip of the shuttle hook aligns with the edge of positioned as in step , and then insert the the race shelf.
S2_brotherE.book Page 102 Thursday, February 13, 2003 11:03 AM APPENDIX —————————————————————————————————————————————————————————— Troubleshooting If the machine stops operating correctly, check the following possible problems before requesting service. If the problem persists, contact your retailer or the nearest authorized service center. Symptom Probable Cause Remedy Reference...
Page 109
S2_brotherE.book Page 103 Thursday, February 13, 2003 11:03 AM Symptom Probable Cause Remedy Reference The upper thread was not threaded correctly (for example, the spool is not installed correctly, the spool cap Correct the upper threading. page 18 is too big for the spool being used, or the thread has come out of the nee- dle bar thread hook).
Page 110
S2_brotherE.book Page 104 Thursday, February 13, 2003 11:03 AM APPENDIX —————————————————————————————————————————————————————————— Symptom Probable Cause Remedy Reference The upper thread was not threaded Correctly thread the upper thread correctly, or the bobbin is incor- and correctly install the bobbin page 16, 18 rectly installed.
Page 111
S2_brotherE.book Page 105 Thursday, February 13, 2003 11:03 AM Symptom Probable Cause Remedy Reference The feed dogs are lowered. Slide the drop feed lever to the left. page 83 The stitch is too fine. Lengthen the stitch length. page 52 The presser foot that is used is not Attach the presser foot that is appro- The fabric does...
S2_brotherE.book Page 106 Thursday, February 13, 2003 11:03 AM APPENDIX —————————————————————————————————————————————————————————— Error messages If the start/stop button is pressed before the sewing machine is correctly set up or if an operation is performed incorrectly, an error message appears in the stitch indicator. Follow the instructions that appear. If you press (Stitch selection key) or do the operation correctly while the error message is displayed, the message disappears.
S2_brotherE.book Page 107 Thursday, February 13, 2003 11:03 AM Changing the needle stop position Normally, the sewing machine is set to leave the needle in the fabric when sewing is stopped. Instead, the machine can be set to leave the needle raised when sewing is stopped. Turn off the sewing machine.
S2_brotherE.book Page 108 Thursday, February 13, 2003 11:03 AM APPENDIX —————————————————————————————————————————————————————————— Index Symbols + key ..............Cover E fagoting .................89 features ................2 feed dog position switch ........Cover C Numerics feed dogs ............Cover C 3-point zigzag stitch ............61 foot controller ..........Cover A foot controller jack ..........
Page 115
S2_brotherE.book Page 109 Thursday, February 13, 2003 11:03 AM patchwork stitching ............81 thick fabrics ..............54 piecing ................81 thin fabrics ..............55 pocket corners .............. 85 thread cutter ............Cover B positioning fabric ............44 thread cutter button ........Cover D presser foot ............Cover C thread guide cover ..........