Table of Contents
Related Manuals for Digi-Pas DWL2000XY
Summary of Contents for Digi-Pas DWL2000XY
- Page 1 ® Digi-Pas ™ Innovation & Technology Driven USER MANUAL 2-Axis Precision Digital Level Model: DWL2000XY REVISION 1.00 Note: Contents in this instruction manual is continuously updated, please check Digi-Pas website for latest version.
- Page 2 Distributed by: Trick-Tools 80 Truman Road Pella, IA 50219 Phone:1-877-VAN-SANT E-mail: sales@trick-tools.com Here at Trick Tools we believe that our customers deserve the best value in their tool and equipment purchases. We are constantly at work searching out a variety of high quality, high performance tools to offer at the best prices possible.
- Page 3 ® Digi-Pas Products were manufactured under ISO9001 & ISO14001 standards, tested to comply by the followings certification bodies: ® © 2012 JSB TECH Pte Ltd. All rights reserved. Digi-Pas logo is registered trademarks of JSB TECH Pte Ltd.
-
Page 4: Table Of Contents
CONTENTS CHAPTER 1: DEVICE OVERVIEW - Technical Specification - Overview CHAPTER 2: SETTING UP - Operating Procedure - Mounting Device on Fixture CHAPTER 3: USER INTERFACE - Single Axis Mode Interface - Dual Axis Mode Interface - Main Menu Icon Functions CHAPTER 4: FEATURES AND SETTING - Absolute Level - Alternate Zero... -
Page 5: Chapter 1: Device Overview
CHAPTER 1: DEVICE OVERVIEW Technical Specification DWL2000XY Measurement Range 0.00° to ± 90.00° (Single Axis Mode) Measurement Range 0.00° to ± 3.00° ( 2-Axis Mode) Resolution 0.01° (175µm/M) (0.002 in/ft) ± 0.02° at 0.00° ~ ± 2.00° (349µm/M) Accuracy (0.004 in/ft) (72 Arcsec) ±... - Page 6 Device Overview Battery Compartment of 4 x “AAA” size 1.5V batteries. -Observe the polarity of the batteries indicated on the top of the battery cover USB Port: LCD Colour graphic digital display - USB power supply - PC Synchronization - Firmware update ON/OFF: Power On/Off - Escape from Mode function CAL: Activate calibration mode...
-
Page 7: Chapter 2: Setting Up
CHAPTER 2: SETTING UP Operation Procedure 1. Insert 4 pieces of "AAA" batteries into the battery compartment and press ON/OFF button. Alternatively, insert USB power source to the USB Port to power up the device. Take note that the device performance might be affected when poorly regulated USB power source is used. -
Page 8: Chapter 3: User Interface
CHAPTER 3: USER INTERFACE Single Axis Mode Interface Single Axis Mode Display Screen and Button Function BATTERY SOUND LEVEL ALERT MEASUREMENT HOLD UNITS DIGITAL MEASUREMENT READING UNITS MAIN MENU Single Axis Mode Operation Place the digital level on the surface to be measured. Please ensure the contact surfaces of the device and measuring plane are clean and free from dust particles. - Page 9 Dual-Axis Mode Interface Dual-Axis Mode Display Screen and Button Function SOUND ALERT BATTERY LEVEL HORIZONTAL (X) AXIS MEASUREMENT DIGITAL READING UNITS MEASUREMENT HOLD UNITS MICROMETER VERTICAL (Y) AXIS DIGITAL READING MAIN MENU Dual-Axis Mode Operation Place the digital level on the surface to be measured. Please ensure the contact surfaces of the device and measuring plane are clean and free from dust particles.
- Page 10 Main Menu Icon Screen Display and Button Function TITLES EXIT MAIN MENU ICONS CURSOR SCROLL LEFT SCROLL RIGHT SELECT / ENTER Main Menu Icon Features ABSOLUTE LEVEL SETTING Enable user to ensure each measurement reading is in accordance to maximum device accuracy specified. ALTERNATE ZERO SETTING Enable user to measure relative angles at a common plane with respect to a reference angle.
-
Page 11: Chapter 4: Features And Setting
CHAPTER 4: FEATURES AND SETTING Absolute Level Screen Display and Button Function BACK TO MAIN MENU INSTRUCTION MEASUREMNT INDICATOR HOLD UNIT LOADING BAR SELECT / ENTER Absolute Level Setting Place the device on the surface to be measured. Press MODE button to start the measurement and wait until the loading bar is full. -
Page 12: Alternate Zero
Alternate Zero Screen Display and Button Function BACK TO MAIN MENU INSTRUCTION HOLD MEASUREMNT INDICATOR UNIT SELECT / ENTER SINGLE OR Dual-AXIS INDICATOR Alternate Zero Setting Place the digital level on the surface to be measured. Press MODE button to set the angle to 0⁰ as a reference. Please ensure the contact surfaces of the device and measuring plane are clean and free from dust particles. - Page 13 Setting Menu Display Screen and Button Function MAIN MENU RIGHT LEFT SELECTION SELECTION DOWN SETTING PARAMETERS AutoOff To set automatic power off according to user defined time period. AutoDim To set automatic dim according to user defined time period. Units To change the measuring unit (Degree, mm/M, In/FT).
-
Page 14: Chapter 5: Storage And Cleaning
CHAPTER 5: STORAGE AND CLEANING Storage Keep the device in the equipment box and maintain the storage temperature within -20°C to 60°C or -4°F to 140°F. When the device is not in used, the batteries are to be removed from the device. -
Page 15: Chapter 6: Warranty
CHAPTER 6: WARRANTY ® Digi-Pas 2-Axis High Precision Digital level is warranted to the original purchaser to be free from defects in workmanship and material. JSB Tech will, at its option, repair or replace any defective part which may malfunction under normal and proper use within a period of 2 (two) years from the date of purchase. The forgoing warranty shall not apply to defects resulting from misuse, abuse, assignment, or transfer by the Buyer. -
Page 16: Appendix: User Calibration
APPENDIX: USER CALIBRATION Calibration Instruments: Grade AA (Levelled to ≤1.0 arcsec) Granite Table Flatness : ≤ 2.0µm Perpendicularity: ≤ 2.0µm Master Square Master Square Parallelism: ≤ 2.0µm Granite Table Calibration Procedures: Ensure the DWL3000XY device is in power OFF condition. Press and hold the CAL button by using a small pin and simultaneously press the ON/OFF button. - Page 17 4. Turn the device 180° and place on the opposite side of the master square as shown in Position 4. Hold the device firmly and do not move the device during each count down period. Press the MODE button again to start the calibration and wait until the countdown reach “0”, the LCD screen displays “Calibration 5”...
Need help?
Do you have a question about the DWL2000XY and is the answer not in the manual?
Questions and answers