Download Table of Contents Print this page
NEC E805-PC2 User Manual

NEC E805-PC2 User Manual


Quick Links

User's Manual


Table of Contents

Summary of Contents for NEC E805-PC2

  • Page 1 User’s Manual E705 E805...
  • Page 2: Table Of Contents

    Index Declaration of conformity ..........................English-1 Important Information ........................... English-2 WARNING ............................English-2 CAUTION ............................English-2 Safety Precautions, Maintenance & Recommended Use ................English-3 Contents ............................... English-4 Installation ..............................English-5 Attaching Mounting Accessories ..................... English-6 Parts Name and Functions ........................... English-8 Control Panel ..........................
  • Page 3: Declaration Of Conformity

    Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation. OmniColor is a registered trademark of NEC Display Solutions Europe GmbH in the countries of EU and Switzerland. DisplayPort and DisplayPort Compliance Logo are trademarks owned by the Video Electronics Standards Association.
  • Page 4: Important Information

  • Page 5: Safety Precautions, Maintenance & Recommended Use

    • Cable distribution system should be grounded (earthed) in accordance with ANSI/NFPA 70, the National Electrical Code (NEC), in particular Section 820.93, Grounding of Outer Conductive Shield of a Coaxial Cable. • The screen of the coaxial cable is intended to be connected * The product you purchased may not have this feature.
  • Page 6: Contents

    Contents Your new monitor box* should contain the following: • LCD monitor • Setup Manual • Power cord* • Clamp x 1 • Video Signal Cable • Screw with washer (M4 x 10) x 1 • Wireless Remote Control and AAA Batteries •...
  • Page 7: Installation

    DO NOT mount the unit to trim or to hanging • When using mounting accessories other than those that fixtures. are NEC approved, they must comply with the VESA- compatible (FDMlv1) mounting method. Maintenance • NEC recommends mounting interfaces that comply with •...
  • Page 8: Attaching Mounting Accessories

    Install the stand in the direction of the arrow damage the monitor. which is imprinted on the surface of the stand. When using mounting accessories other than NEC compliant Use the ST-801. and approved, they must comply with the VESA-compatible mounting method.
  • Page 9 5. Ventilation Requirements When mounting in an enclosed space or recessed area, leave adequate room between the monitor and the enclosure to allow heat to disperse, as shown below. Allow adequate ventilation or provide air conditioning around the monitor, so that heat can properly dissipate away from the unit and mounting apparatus;...
  • Page 10: Parts Name And Functions

    Parts Name and Functions Control Panel POWER button ( EXIT button (EXIT) Switches the power on/off. See also page 16. Activates the OSD menu when the OSD menu is turned-off. Acts as EXIT button within the OSD to move to previous MUTE button (MUTE) menu.
  • Page 11: Terminal Panel

    Terminal Panel AC IN connector VGA IN (mini D-Sub 15 pin) Connects with the supplied power cord. To input analog RGB signals from a personal computer or from other RGB equipment. This input can be used with an Main Power Switch RGB or COMPONENT source.
  • Page 12: Wireless Remote Control

    Wireless Remote Control AUDIO INPUT button Selects audio input source [IN1], [IN2], [OPTION]* , [HDMI], [DPORT], [HDMI2]. OPTION MENU button* KEYPAD Press buttons to set and change passwords, change channel and set REMOTE ID. ENT button* DISPLAY button Turns on/off the information OSD. See page 18. MENU button Turns on/off the menu mode.
  • Page 13: Operating Range For The Remote Control

    Operating Range for the Remote PIP (Picture In Picture) button Control ON/OFF button: Toggle switches between PIP, POP, PICTURE BY PICTURE-ASPECT and PICTURE BY Point the top of the remote control toward the LCD monitor’s PICTURE-FULL. See page 22. remote sensor during button operation. INPUT button: Selects the “picture in picture”...
  • Page 14: Setup

    Setup 1. Determine the installation location NEC recommends the following battery use: • Place “AAA” size batteries matching the (+) and (-) signs CAUTION: Installing your LCD monitor must be done by a on each battery to the (+) and (-) signs of the battery qualified technician.
  • Page 15 5. Switch on the power of all the attached external equipment When connected with a computer, switch on the power of the computer first. 6. Operate the attached external equipment Display the signal from the desired input source. 7. Adjust the sound Make volume adjustments when required.
  • Page 16: Connections

    Connections NOTE: Do not connect/disconnect cables when turning on the monitor or other external equipment as this may result in a loss of the monitor image. NOTE: Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound. Before making connections: First turn off the power of all the attached equipment and make connections.
  • Page 17: Connecting A Personal Computer

    Connecting a Personal Computer Connecting your computer to your LCD monitor will enable you to display your computer’s screen image. Some video cards may not display an image correctly. Your LCD monitor displays proper image by adjusting the factory preset timing signal automatically. <Typical factory preset signal timing>...
  • Page 18: Basic Operation

    Basic Operation Power ON and OFF Modes The LCD monitor power indicator will turn green while powered on and will turn red or amber while powered off. NOTE: The Main Power Switch must be in the ON position in order to power up the monitor using the remote control or the Power Button.
  • Page 19: Power Indicator

    Power Indicator Picture Aspect DVI, VGA, DPORT Mode Status Indicator Light FULL ZOOM NORMAL Power ON Green* Power OFF and Power Save “AUTO HDMI, Y/Pb/Pr, HDMI2 POWER STANDBY” Power consumption under 0.5 W FULL WIDE DYNAMIC ZOOM NORMAL Power Save “AUTO POWER SAVE” Amber Power consumption under 2.5 W* Aspect ratio...
  • Page 20: Information Osd

    Information OSD The Information OSD provides information such as: Input Source, Picture Size, etc. Press the DISPLAY button on the remote to bring up the Information OSD. Input Name Audio input mode Picture aspect Input Signal Information Sub picture information Picture Mode DVI, VGA, DPORT STANDARD...
  • Page 21: Osd (On-Screen-Display) Controls

    OSD (On-Screen-Display) Controls NOTE: Some functions may not be available depending on the model or optional equipment. Input source Main Menu Icons Main Menu Item Adjustment Settings Sub Menu THANK YOU FOR SAVING THE ENVIRONMENT. CARBON FOOTPRINT 86.0 % PICTURE MODE Select Goto Adjustment Return...
  • Page 22: Picture

    (S-Curve). DICOM SIM. DICOM GSDF curve simulated for LCD type. PROGRAMMABLE1, 2, 3 A programmable gamma curve can be loaded using NEC optional software. MOVIE SETTINGS NOTE: When INPUT2 of SUPER is selected in INPUT CHANGE and displayed, this function cannot be changed.
  • Page 23: Audio

    PHASE Adjusts the visual “noise” on the image. VGA, Y/Pb/Pr inputs only H RESOLUTION Adjusts the horizontal size of the image. VGA inputs only V RESOLUTION Adjusts the vertical size of the image. VGA inputs only INPUT RESOLUTION If there is a problem with signal detection, this function forces the monitor to display the signal at AUTO VGA inputs only the desired resolution.
  • Page 24: Schedule

    BASS To accentuate or reduce the low frequency sound. Press + button to increase BASS sound. Press - button to decrease BASS sound. SURROUND Artificial surround sound. NOTE: Audio out is disabled when this function is set to ON. PIP AUDIO Selects source of PIP audio.
  • Page 25: Osd

    BLEND Sets the transparency of the Text Ticker (0: transparent, 100: opaque). DETECT Enables auto-detection of the Text Ticker. FADE IN Enables fade-in of the text ticker. RESET Resets PIP options back to factory settings except SUB INPUT and ASPECT. LANGUAGE Select the language used by the OSD.
  • Page 26 IR LOCK SETTINGS Prevents the monitor from being controlled by the wireless remote control. UNLOCK When ACTIVATE is selected, all the settings are activated. NOTE: IR LOCK SETTINGS is a function intended only to the wireless remote control buttons. This function does not lock out access to all buttons at the back of the monitor. To return to normal operation, press the “DISPLAY”...
  • Page 27: Display Protection

    DISPLAY PROTECTION POWER SAVE Sets how long the monitor waits to go into power save mode after the signal is lost. AUTO NOTE: When connecting DVI, the video card might not stop sending the digital data even STANDBY though the image might have disappeared. If this occurs the monitor will not switch into power management mode.
  • Page 28: Advanced Option1

    SUBNET MASK: Set your subnet mask number of the network connected to the monitor when “MANUAL” is selected for [IP SETTING]. DEFAULT GATEWAY: Set your default gateway of the network connected to the monitor when “MANUAL” is selected for [IP SETTING].
  • Page 29 TERMINAL SETTING DVI MODE Selects the kind of DVI-D equipment which is connected to the DVI input. Select “DVI-HD” when DVI-HD DVD player or computer equipment, which requires HDCP authentication, is connected. Select “DVI-PC” when a computer equipment, which not requires HDCP authentication, is connected. D-SUB MODE Selects the type of signal associated with the D-SUB input.
  • Page 30: Advanced Option2

    120Hz (not adjustable) TOUCH PANEL (not adjustable) RESET Resets the following settings within the ADVANCED OPTION menu back to factory setting: INPUT DETECT (except the priority of input signals), INPUT CHANGE (except for INPUT1 and INPUT2), TERMINAL SETTING, DEINTERLACE, COLOR SYSTEM, OVER SCAN, AUDIO in OPTION SETTING.
  • Page 31 As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.
  • Page 32: Remote Control Function

    Remote Control Function REMOTE CONTROL ID FUNCTION Monitor ID:1 Monitor ID:2 Monitor ID:3 REMOTE CONTROL ID The remote control can be used to control up to 100 individual monitors using what is called Remote works Remote works Remote works the REMOTE CONTROL ID mode. The REMOTE CONTROL ID mode works in conjunction with the Monitor ID, allowing control of up to 100 individual monitors.
  • Page 33: Controlling The Lcd Monitor Via Rs-232C Remote Control

    Controlling the LCD monitor via RS-232C Remote Control This LCD monitor can be controlled by connecting a personal computer with a RS-232C terminal. Functions that can be controlled by a personal computer are: • Power ON or OFF. • Switching between input signals. •...
  • Page 34 2) Control command diagram For other commands, please see “External_Control.pdf” file on the CD-ROM. Function (Monitor ID = 1) Code Data Power ON 01 30 41 30 41 30 43 02 43 32 30 33 44 36 30 30 30 31 03 73 0d Power OFF 01 30 41 30 41 30 43 02 43 32 30 33 44 36 30 30 30 34 03 76 0d Input Source Select DisplayPort...
  • Page 35: Controlling The Lcd Monitor Via Lan Control

    Controlling the LCD monitor via LAN Control Connecting to a Network Using a LAN cable allows you to specify the Network Settings and the Alert Mail Settings by using an HTTP server function. To use a LAN connection, you are required to assign an IP address. Example of LAN connection: Server NOTE: Use a category 5 or higher LAN cable.
  • Page 36 Example 1: When the host name of the monitor has been set to “”, access is gained to the network setting by specifying for the address or the entry column of the URL.
  • Page 37 Network Setting Click “NETWORK” on the left side of HOME. IP SETTING Set for IP ADDRESS setting. AUTO: Automatically assign an IP address. MANUAL: Set your IP address of the network connected to the monitor. NOTE: Consult your network administrator for the IP address when [AUTO] is selected for [IP SETTING].
  • Page 38 Mail Setting Click “MAIL” on the left side of HOME. This option notifies your computer of an error message via e-mail when using wired LAN. An error message notification will be sent when an error occurs in the monitor. ALERT MAIL Checking [ENABLE] will turn on the Alert Mail feature.
  • Page 39 Alert error message list Error number Alert mail Message Explanation Measure * ErrorCode The monitor’s power supply is not Standby power Abnormal Please contact your supplier. 70h ~ 7Fh functioning normally. 80h ~ Fh The cooling fan has stopped. Cooling fan Abnormal Please contact your supplier.
  • Page 40 SNMP Setting Click “SNMP” on the left side of HOME. This function allows for getting status and controlling of a monitor via the network. Version: SNMP v1 Authenticated plaintext by community name, not return a confirmation message of Trap. SNMP v2c Authenticated plaintext by community name, return a confirmation message of Trap. Community name: The default setting of community name is “public”.
  • Page 41 AMX Setting Click “AMX” on the left side of HOME. AMX BEACON Turn on or off for detection from AMX Device Discovery when connecting to the network supported by AMX’s NetLinx control system. TIP: When using a device that supports AMX Device Discovery, all AMX NetLinx control system will recognize the device and download the appropriate Device Discovery Module from an AMX server.
  • Page 42 Name Setting Click “NAME” on the left side of HOME. MONITOR NAME Set a monitor name. The name must be 16 characters or less. The default is model name. HOST NAME Type in the hostname of the network connected to the monitor. Up to 15 alphanumeric characters can be used.
  • Page 43 Memo Setting Click “MEMO” on the left side of HOME. Set a title and meesage. TITLE A title must be 24 characters or less. MESSAGE A message must be 240 characters or less. MEMO PASSWORD The default is “0000”. MEMO PASSWORD MEMO PASSWORD is required when setting MEMO.
  • Page 44: Point Zoom

    POINT ZOOM Using “SET/POINT ZOOM” button on a remote control allows to enlarge a partial of image. Press CH+/- button to zoom up or down. The image can be expanded from 1 to 10 times. 1 Press [SET/POINT ZOOM] button on a remote control. An icon will be a magnifier. 2 Move magnifier icon by [ ] [ ] [+] [-] button.
  • Page 45: Features

    FullScan Capability: Allows you to use the entire screen area in most resolutions, significantly expanding image size. VESA Standard (FDMIv1) Mounting Interface: Allows you to connect your LCD monitor to any VESA standard (FDMIv1) third party mounting arm or bracket. NEC recommends using mounting interface that comply with TÜV-GS and/or UL1678 standard in North America.
  • Page 46: Troubleshooting

    • Check if batteries are inserted correctly. NOTE: As with all personal display devices, NEC DISPLAY • Check if the Remote Control is pointing at the monitor’s SOLUTIONS recommends displaying moving images remote sensor.
  • Page 47: Specifications - E705

    Specifications - E705 Product Specifications LCD Module 70”/1765.6 mm diagonal Resolution: 1920 x 1080 Color: Over 16 million colors (depending on video card used) Frequency Horizontal: 15.625/15.734 kHz, 31.5 kHz - 91.1 kHz (Analog Input) 31.5 kHz - 91.1 kHz (Digital Input) Vertical: 50.0 - 85.0 Hz Pixel Clock...
  • Page 48: Specifications - E805

    Specifications - E805 Product Specifications LCD Module 80”/2032.2 mm diagonal Resolution: 1920 x 1080 Color: Over 1073 million colors (depending on video card used) Frequency Horizontal: 15.625/15.734 kHz, 31.5 kHz - 91.1 kHz (Analog Input) 31.5 kHz - 91.1 kHz (Digital Input) 50.0 - 85.0 Hz Vertical: Pixel Clock...
  • Page 49: Pin Assignment

    Pin Assignment 1) Analog multi input (MiniDsub15p): VGA, Y/Pb/Pr Pin No Name Red, Y/Pb/Pr_Pr Green, Y/Pb/Pr_Y Blue, Y/Pb/Pr_Pb Mini D-SUB 15P (Monitor side) DDC-GND Red-GND Green-GND Blue-GND +5V (DDC) DDC-SDA H-SYNC V-SYNC DDC-SCL 2) RS-232C input Pin No Name D-SUB 9P (Monitor side) This LCD monitor uses RXD, TXD and GND lines for RS-232C control.
  • Page 50: Manufacturer's Recycling And Energy Information

    Manufacturer’s Recycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally-friendly products, and always strive to help define and comply with the latest independent standards from agencies such as ISO (International Organisation for Standardization) and TCO (Swedish Trades Union).

This manual is also suitable for:


Table of Contents