Midi Filter; Program Change (Pc) Table; Program Change Transmit; Transmit Filter - Yamaha P-200 Owner's Manual

ENABLE
When set to Enable, the Panel Switch Lock function can be used;
in other words, double clicking a [VOICE SELECT] button will lock
the panel controls (according to the instructions on page 41).

MIDI Filter

The MIDI Filter function lets you select the various types of
MIDI data which will be transmitted or received. (Note: The
abbreviation "TX" stands for "Transmit" and the abbreviation
"RX" stands for "Receive".) Position the cursor over the
Message type or on/off status using the [1] and [q] buttons.

TRANSMIT FILTER

The Transmit Filter settings let you determine which types of
MIDI messages are transmitted from the P-200.
TX FILTER
note on/off=off
Message type
MESSAGE TYPES
Message types include Note On/Off, Control Change, Program
Change, Aftertouch, Pitch Bend, Channel Mode Message,
Parameter Change and Bulk and FA/FB/FC. (Select the message
types with the [-1/NO] and [+1/YES] buttons.)
ON, OFF
Setting the message type to On status will filter this particular
data, and therefore it will not be transmitted via the [MIDI OUT]
terminal. Setting the message type to Off status will allow the
particular data to be transmitted.
NOTE
The default setting for Parameter Change is set to On; all others are set to
Off. When controlling external devices such as a tone generator, Exclusive
and Bulk should be set to On. When you record your P-200 Performance to
an external sequencer and play it back, Exclusive and Bulk should be set to
Off.

RECEIVE FILTER

The MIDI Receive Filter settings let you determine which types
of incoming MIDI messages are received. When set to On, the
specific data can be protected.
RX FILTER
note on/off=off
Message type
MESSAGE TYPES
Message types include Note On/Off, Control Change, Program
Change, Pitch Bend, Channel Mode Message, Parameter Change
and Bulk. (Select the message types with [-1/NO] and [+1/YES]
buttons.)
ON, OFF
Setting the message type to On status will filter this particular data,
and therefore it will not be received at the [MIDI IN] terminal.
Setting the message type to Off status will allow the particular data
to be received.

Program Change (PC) Table

The Program Change Table function lets you assign program
change numbers to incoming and outgoing program change
messages.

PROGRAM CHANGE TRANSMIT

The Program Change Transmit function lets you assign
program change transmit numbers to each voice or
Performance. You can also assign bank numbers (MSB/LSB)
as bank select messages.
Your P-200 can transmit a program change message each
time you press a [SELECT] button in Voice or Performance
mode. (You can have the number of the program change
message display briefly when you select a voice or
Performance. For details, see page 52.)
At the factory your P-200 was preset so that each [SELECT]
button will send the program change number corresponding to
the number above the button in Voice mode (1 ~ 12), followed
by subsequent numbers in Performance mode, for A and B
banks (13 ~ 36).
%
Therefore, when the P-200 is in Voice mode, an external tone
generator connected to the P-200 will receive messages
selecting program 1 when you press the [PIANO 1] button,
program 2 when you press the [PIANO 2] button, and so on.
When the P-200 is in Performance mode and bank A is
selected, an external tone generator will receive messages
selecting program 13 when you press [PIANO 1]. Likewise,
when bank B is selected, program 25 will be selected when
you press [PIANO 1].
The settings for which program change number is assigned to
which [SELECT] button are grouped in a table known as the
program change transmit table, which you can access to
assign a program change number (between 1 and 128, or Off)
to each of the [SELECT] buttons according to Play mode.
You can also select a bank number combining the MSB (Most
Significant Byte) and LSB (Least Significant Byte). This makes
it possible to select any program on a MIDI device that has
more than 128 programs.
Select assign
These parameters let you access each [SELECT] button, with V01
%
~ V12 representing the Voice Play mode [VOICE SELECT]
buttons, and A01 ~ A12 representing the Performance Play mode
A bank [PERFORMANCE SELECT] buttons, and B01 ~ B12
representing the Performance Play mode B bank
[PERFORMANCE SELECT] buttons. As you step through each
one, the name will appear in the first line of the screen, and the
current assignments will appear in the second line.
NOTE
You can choose a specific Voice button number by holding [VOICE] and
pressing the desired [VOICE SELECT] button. You can choose a specific
Performance A bank button number by holding [PERF. A] and pressing the
desired [PERFORMANCE SELECT] button. You can choose a specific
Performance B bank button number by holding [PERF. B] and pressing the
desired [PERFORMANCE SELECT] button.
53
PC TX
V01=(OFF/OFF)
SELECT ASSIGN (V01~V12, A01~A12, B01~B12)
%
1