Intended use Automatic switch off / interior light . . 21 Intended use Switching off the appliance..22 Interrupting the programme ..22 I n t e n d e d u s e This appliance is intended for Terminating the programme .
Safety instructions Delivery The electrical connection conditions must correspond 1. Check the packaging and with the specifications dishwasher immediately for on the dishwasher rating plate 92. damage caused in transit. Do not switch on a damaged If the power cord of this appliance, but contact your appliance is damaged, supplier.
Safety instructions If you cannot obtain any In daily use information from Read and observe the safety the manufacturer, you must information and instructions not install the dishwasher for use on the packaging above or below these for cleaning and rinsing agents. appliances.
Safety instructions Deactivating the button lock: Disposal Hold down the button + for 1. Make redundant appliances unusable to prevent approx. 4 sec. until the subsequent accidents. display goes out. 2. Dispose of the appliance in a When the programme ends n environmentally friendly on the digital display), the manner.
Page 8
Safety instructions Keep children away from Warning open dishwasher. Risk of explosion! The water in the rinsing Do not add any solvents compartment is not drinking to the washing chamber. water and could contain Danger of explosion! detergent residue. Ensure that children do not Warning place fingers in the tablet collecting tray 1B.
Protection of the environment Protection of the Getting to know your environment appliance i o n P r o t e c t o f t e n v i r o n m e n t G e t t i t o k n o w y o u r a p p l i a n c...
Water softening system/Special salt Appliance interior Water softening system/Special salt 1" Interior light * W a t e r s o f t e n i s y s t e m / S p e c i s a l t 1* Cutlery drawer To ensure good washing results, 12 Top basket...
Water softening system/Special salt As soon as the salt refill indicator @ To change the setting: on the fascia is lit, top up the salt. 1. Press programme button 3. Each time the button is pressed, the set value increases by one level; when the value of : has been reached, the display jumps back...
Rinse aid Setting amount of rinse aid Rinse aid R i n s e a i d The amount of rinse aid can be set from to : . Please set rinse aid on As soon as the rinse-aid refill indicator H is lit on the fascia, there to obtain very good drying results is already set in factory).
Utensils Loading the dishwasher Utensils U t e n s i 1. Remove large food remnants. It is not necessary to prerinse utensils Not suitable under running water. 2. Place the utensils so that Cutlery and utensils made of wood. –...
Utensils Cups and glasses Other examples, such as the best way Top basket 12 of loading your dishwasher, can be found on our homepage as a free download. The corresponding Internet address can be found on the back page of these instructions for use. Cutlery drawer Arrange the cutlery in the cutlery drawer 1* as illustrated.
Detergent Small accessories holder * S m a l l a c c e s s o r i e s h o l d e r * depending on model Light-weight plastic accessories, e.g. cups, lids, etc. can be held securely in the small accessories holder.
Detergent Note 2. Close the cover on the detergent dispenser by sliding it up until the To ensure a good washing result, lock engages without difficulty. always follow the instructions on the detergent packaging! If you have further questions, we recommend that you contact the detergent manufacturers’...
Detergent Combination detergent Notes You will obtain optimum rinsing Apart from conventional detergents and drying results by using solo (Solo), a number of products are offered detergents and applying salt with additional functions. These and rinse aid separately. products contain not only the detergent If programmes are short, tablets but also rinse-aid and salt replacement may not have full cleaning effect...
Overview of programmes Overview of programmes p r o g r a m m e s O v e r v i e w o f The max. possible number of programmes is illustrated in this overview. The corresponding programmes and their arrangement can be found on the fascia.
Additional options § Programme selection Half load * H a l f l o a d You can select a suitable programme If you have only a few items to wash according to the type of utensils and (e.g. glasses, cups, plates), you can degree of soiling.
Operating the appliance Switching on the appliance Operating the appliance 1. Turn on the tap fully. 2. Switch on ON/OFF switch (. O p e r a t i i a n c e t h e a p p l The Eco 50°...
Operating the appliance Remaining running time Automatic switch off after end display of programme or interior light* A u t o m a t i c s w i t c h o f f / i n t e r i o r l i g h t When the programme is selected, the * depending on model remaining running time of the...
Operating the appliance To change the setting: T erminating the programme T e r m i n a t i n g t h e p r o g r a m m e 1. Press programme button 3. (Reset) Each time the button is pressed, the set value increases by one level;...
Cleaning and maintenance Never use a steam cleaner to clean your Cleaning and dishwasher. The manufacturer is not liable for any consequential damage. maintenance Regularly wipe the front of the appliance C l e a n i a n d n a n c e m a i n t e and fascia with a damp cloth;...
Cleaning and maintenance Filters Spray arms The filters 1Z keep large foreign Limescale objects in the rinsing water away from and contaminants in the rinsing water the pump. These foreign objects may may block nozzles and bearings on the spray arms 1: occasionally block the filters.
Fault, what to do? In this case: Fault, what to do? 1. First always disconnect F a u l t , w h a t d o ? the appliance from the power supply. Experience has shown that you can 2.
Fault, what to do? Fault table Fault Cause Remedial action “Check water supply” Supply hose kinked. Install supply hose without kinks. display 8 lights up. Tap turned off. Turn the tap on. Tap jammed or calcified. Turn the tap on. Flow rate must be min.
Page 27
Fault, what to do? Fault Cause Remedial action A different error code is A technical fault has probably Switch off appliances with the ON/OFF switch (. After a short time restart the indicated on the digital occurred. display. appliance. to : If the problem recurs, turn off the tap and pull out the mains plug.
Page 28
Fault, what to do? Fault Cause Remedial action Utensils not dry. No or too little rinse aid in the Refill rinse aid. dispenser. Programme selected without Select programme with drying (see drying. “Overview of programmes”, “Programme sequence”). Water collecting in depressions Arrange utensils in a sloping position, on the utensils and cutlery.
Page 29
Fault, what to do? Fault Cause Remedial action Food remnants on the Utensils placed too closely Arrange utensils with adequate clearance utensils. together, utensils basket between them ensuring that the spray jets overfilled. can reach the surface of the utensils. Prevent contact points.
Page 30
Fault, what to do? Fault Cause Remedial action Water stains on plastic Droplet formation on plastic Use a more intensive programme (more parts. surface is physically unavoidable. water changes). After drying, water stains are Arrange utensils in a sloping position. visible.
Page 31
Fault, what to do? Fault Cause Remedial action Coloured (blue, yellow, Film formation consisting of Can be partly removed with machine brown), difficult to remove ingredients from vegetables (e.g. cleaner or by mechanical cleaning. Coatings to non-removable coatings cabbage, celery, potatoes, are harmless.
Page 32
Fault, what to do? Fault Cause Remedial action Rust spots on the cutlery. Cutlery not adequately rust- Use corrosion-resistant cutlery. resistant. Knife blades are frequently more severely affected. Cutlery will also rust if rusting Do not wash rusting parts. parts are rinsed at the same time (pan handles, damaged utensil baskets, etc.).
Page 33
Fault, what to do? Fault Cause Remedial action Appliance stops in the Door not closed properly. Close the door. programme or programme Do not place utensils or fragrance Check whether rear panel is being pressed is interrupted. dispenser in the tablet collecting in, e.g.
Customer service Customer service Installation and connection C u s t o m e r s e r v i c e If you are unable to rectify the fault, l a t i o n I n s t a l a n d c o n n e c t i please contact your customer service.
Installation and connection Delivery Installation Your dishwasher has been checked The required installation dimensions can thoroughly in the factory to ensure that it be found in the installation instructions. is in working order. This may cause Level the appliance with the aid of the small water stains.
Installation and connection Drinking water connection Warm water connection * W a r m w a t e r c o n n e c t i o n 1. Fasten the drinking water connection * depending on model to the tap according The dishwasher can be connected to the installation instructions using to cold or hot water up to max.
Installation and connection Electrical connection Removing the appliance Connect the appliance to an Also observe alternating current only, ranging from the sequence of worksteps here. 220 V to 240 V and 50 Hz or 60 Hz 1. Disconnect the appliance from via a correctly installed socket with the power supply.
Installation and connection Transportation Protection against frost P r o t e c t i o n a g a i n s t f r o s t ( E m p t y i n g t h e a p p l i a n c e ) Empty the dishwasher and secure loose If the appliance is in a room where there parts.
Page 40
*9000869802* 9000869802 en (9405) 440MG...