Related Manuals for LG 32LX761H.AHK
Summary of Contents for LG 32LX761H.AHK
- Page 1 INSTALLATION MANUAL LED TV* Please read this manual carefully before operating your set and retain it for future reference. LX76** www.lg.com...
-
Page 2: Table Of Contents
LANGUAGE & COUNTRY SELECTION - TV Name - Automatically for Setup - SoftAP - Manually for Setup TV MANAGER - USB LG Smart Install Utility - USB Download Menu INSTALLATION MENU INTRODUCTION LG HOTEL MODE - Hotel Mode Operation - Power On Status... -
Page 3: Location And Function Of Controls
LOCATION AND FUNCTION OF CONTROLS LOCATION AND FUNCTION OF CONTROLS Parts and Button Screen Remote control and Intelligent sensors Power Indicator Intelligent sensor - Adjusts the image quality and brightness based on the surrounding environment. Joystick Button - This button is located below the TV screen. NOTE You can set the power indicator light to on or off by selecting General in the main menus. -
Page 4: Ezmanager
EZMANAGER EZMANAGER • Image shown may differ from your TV. INTRODUCTION The Pro:Centric Platform enables you to simply install, manage and use guest-centric solutions. The default Domain “procentric.local” and IP Server Address are needed to be registered in DNS TV will contact the IP Server using the default Domain “procentric.local” via IP on server search page. If TV doesn’t contact the Server, TV will search the pre-defined channel earlier than all channels. -
Page 5: Language & Country Selection
EZMANAGER LANGUAGE & COUNTRY SELECTION - Please select the Language and Country. Some countries need to select the Time Zone. -
Page 6: Automatically For Setup
EZMANAGER Automatically for Setup From the TV Configuration Options screen, you can choose how to proceed with the configuration of this TV. Whether you will configure the TV for Pro:Centric operation via the wizard or use a USB memory device to configure the TV, you may first wish to set the Room Number on the TV. - If you intend to set Room Number as part of the TV configuration, use the Room Number option to assign the Room # for this TV before you continue with additional configuration. - Page 7 EZMANAGER This step automatically searches for the Pro:Centric Server. If was found the Pro:Centric data channel, select the ‘NEXT’ .
- Page 8 EZMANAGER Downloading the Pro:Centric application files takes few minutes. After the installation is completed, the following screen will be displayed.
-
Page 9: Manually For Setup
EZMANAGER Manually for Setup Select a Label and/or enter the Room Number using the numeric keypad on the remotes or using the virtual keyboard on the TV screen. To continue, move and select ‘NEXT’ . Please select the ‘MANUAL PRO:CENTRIC’ . - Page 10 EZMANAGER Configure the appropriate Pro:Centric settings in the TV.
- Page 11 EZMANAGER Downloading the Pro:Centric application files takes few minutes. After the installation is completed, the following screen will be displayed.
-
Page 12: Usb Lg Smart Install Utility
EZMANAGER USB LG Smart Install Utility Select the ‘USB CONFIGURATION’ →‘TV MANAGER’ . - If you have USB Memory for “LG_DTV” or “lg_dtv” folder, this step shows the USB file list for downloading the items. - Page 13 EZMANAGER Downloading the Pro:Centric application files takes few minutes. After the installation is completed, the following screen will be displayed.
-
Page 14: Installation Menu
The abundant functions for Hotel TV linked with software installation can be projected on OSD as ‘Installation Menu’ . The wide range of hotel features can be performed simply on additional window to enhance the LG hotel TV’s easy installation and convenient operation for Hotelier and System Integrators. -
Page 15: Lg Hotel Mode
INSTALLATION MENU LG HOTEL MODE button to select the LG HOTEL MODE SETUP. Use the Use the ‘OK’ button and then button to select Hotel Mode Operation. - When ‘Hotel Mode Operation’ is set to Yes (Work), all functions of Hotel Mode apply. -
Page 16: Volume
INSTALLATION MENU Volume - Decide to apply volume policy of ‘Start Volume’ , ‘Maximum Volume’ and ‘Minimum Volume’ as Yes(Work) or No(Do Not Work). - (0 ≤ Min ≤ Start ≤ Max ≤ 100) Start Volume y This entry sets the start volume level when is power on. - The level is specified as a number between minimum volume to maximum value. -
Page 17: Dtv Programme Update
INSTALLATION MENU Menu Display y Function to decide whether work with menu (including relevant menus too) of control key (Yes – Enter possible) or not (No – Enter Impossible). - Although select No(Enter impossible), the action that press a Menu button for 5 seconds to enter ‘Installation Menu’ is available. - When select Yes(Enter possible), Menu works. -
Page 18: Radio Video Blank
INSTALLATION MENU Radio Video Blank - Set to Yes(Work) or No(Do Not Work). - Programme that is set to ‘Radio Programme’ and only has Sound should decide whether to set ‘Video Blank’ or not. - When ‘Radio Video Blank’ is set to Yes(Work), ‘Video Blank’ works only in case of Radio Programme. - Although set to Yes(Work), if there are Video signal, ‘Video Blank’... -
Page 19: Network
INSTALLATION MENU NETWORK Use the button to select the NETWORK. MAC Address - Displays the MAC address (not customizable). Network Setting One-click network connection - Connects easily to a wired/wireless network. - Network Connection to connect to an available network automatically. Follow the prompts on the TV. To connect to a network through Set Expert - For use in special circumstances such as in offices (in cases where a static IP is used). -
Page 20: Ip Stream Control
INSTALLATION MENU IP Stream Control Audio PTS Offset - Controlling output stream timing of audio. Video PTS Offset - Controlling output stream timing of video. Wake On LAN - Sets the Wake On LAN function to Enable or Disable. Use “Magic Packet”. -
Page 21: Pro:centric
INSTALLATION MENU PRO:CENTRIC Use the button to select the PRO:CENTRIC. Mode - Sets whether or not enable Pro:Centric and the service method . - You can set to Off, Flash, GEM or HTML using the button . The default value is Off; when it is set to Off, all the sub items are disabled. -
Page 22: Media Type
INSTALLATION MENU Media Type - Sets the medium type to RF or IP. The default value is RF. • Data Channel Freq(KHz) - Sets the RF frequency at which the Pro:Centric data is received. • Data Channel Type - Sets the RF modulation type to DVB-T or DVB-C. The default value is DVB-T. -
Page 23: General
INSTALLATION MENU GENERAL Configuration Setup Select RCU - It is a mode to set whether to use Select RCU or not. When ‘Select RCU’ is set to ‘Enable’ , You can adjust ‘Number of RCU’ menu. Number of RCU - It is a mode to set Number of RCU. Number of RCU value range 1~9. - Page 24 INSTALLATION MENU RS232 DC Power Outlet - It is a mode to decide whether to output DC or not for power supply to IB Box in Installation Menu. We offer a output terminal in one Pin of RS232C Jack for the use of communication. - 5 V DC Power Outlet and 12 V DC Power Outlet must operate mutually exclusively.
- Page 25 INSTALLATION MENU DTV Programme Update - It is a mode to set whether to update DTV programme automatically or not. When DTV Programme Update is set to ’Auto’ , the function to update TV’s programme map according to dtv programme’s stream information. DTV Programme Update is set to ‘Manual’...
-
Page 26: External Speaker
INSTALLATION MENU External Speaker Volume Control - Selects the volume control method of an external speaker. You can select ‘Off’ , ‘Int Variable’ , ’ Fixed.’ , ’Ext Variable’ by pressing button. Ext Variable uses the External Vol Up/Down Control Line to change the volume up to 1 Watts. Int variable is linked to the main volume OSD and change the volume 0 - 1 Watts. -
Page 27: Hcec Setup
INSTALLATION MENU HCEC Setup CEC Mode - Determines whether to use TVLink-CEC. The default value is No. When No is selected, you cannot set subitems. - If ‘TVLink-CEC’ is selected, TV will not directly work for key input except for power key. And volume related keys will work just in case of Follower volume control mode. -
Page 28: Clock Setup
INSTALLATION MENU Clock Setup Clock Source - You can select ‘Off’ , ‘Pro:Centric’ , ‘TV’ , ‘NTP’ , ‘Admin’ by pressing button. - NTP : Clock is synchronized using Network Time Protocol. It's only enabled when network cable is connected. - Admin : It's automatically set to Admin when clock is updated by commercial protocols like TVLink-HCEC, TVLinkInteractive, or HCAP API. -
Page 29: Password Change
INSTALLATION MENU Password Change - To ensure more security, Password can be changed by installers’ own design. button to select the CHANGE and then press the OK button. Use the Enter four digit password. Input the password again for confirmation. PreLoaded App If you want to use a particular app, you can choose from the menu. -
Page 30: Media Share
INSTALLATION MENU MEDIA SHARE ► You can setting Whether to use for “SmartShare” SmartShare - If you want to see DMS(digital media servers ) in MEDIA SHARE menu, you must select ‘Yes’ in this item. Screen Share - If you want to use Wi-fi Screen Share in MEDIA SHARE menu, you must select ‘Yes’ in this item. Wi-fi Screen Share include two functions(Miracast and intel®... -
Page 31: Dmr
TV. - Supported device : Mobile device based on Android (higher than v4.4 Kitkat) / iOS * Support the lower than v4.4 (Kitkat) on the LG mobile device based on Android - Supported version : Higher than Bluetooth 3.0 DIAL - With this DIAL service, you can launch the target app at Smart Home Launcher bar without select the target app by remote controller. - Page 32 INSTALLATION MENU...
-
Page 33: Tv Manager
INSTALLATION MENU TV MANAGER USB Download Menu * USB Cloning : An Installer can quickly set up and clone multiple TV sets at a property. These cloned TVs will all have the same Master TV Setup: Public Display Mode Installation Menu settings, User A/V settings and the Channel Map. This newer procedure significantly decreases the installa- tion time that would be necessary if the standard RS-232C method were used instead. - Page 34 INSTALLATION MENU - Ez Download is a function that enables users to download the desired items all at once, such as EPK (software update file), TLL (see Export Clone File descriptions for more information regarding file types), Logo Image, etc (TLX, MICOM for Pro:Centric). Splash images and EPK files should be copied into the folder named LG_DTV on the USB.
- Page 35 INSTALLATION MENU If the global TLL and model TLL files exist in the same USB root directory, then only the global TLL will be shown. If the global TLL has been deleted, then the model TLL will be shown. Logo Image Download - If there are more than two USB Memory Device, It is possible to select the USB.
- Page 36 INSTALLATION MENU NOTE Splash Image update function supports only JEPG,BMP format file of less than 8 MB filesize. We recommend you that splash image resolution match the TV`s panel resolution. Max resolution of splash image : Full HD → 1920 x 1080, HD → 1360 x 768. Min resolution of splash image : Full HD →...
- Page 37 INSTALLATION MENU - This feature update EPK of TV through the hex file in USB. The target file is located in \LG_DTV folder. - If there are more than two USB memory Device, It is possible to select the USB. - The download sequence is Update TV Software →...
- Page 38 INSTALLATION MENU - This feature update MICOM of TV through the hex file in USB. The target file is located in \LG_DTV folder - If there are more than two USB memory Device, It is possible to select the USB. - The download sequence is Update Micom Software →...
- Page 39 INSTALLATION MENU Export Clone File - "Export Clone File” must be done first before “Import Clone File” process, as it generate the file to be used in “Export Clone File”. While writing is in process, the user must not turn TV off nor unplug the USB memory card. The steps in “Export Clone File” are explained below. The following images might be slightly different than the OSD image.