Related Manuals for LG 22LW760V.AEU
Summary of Contents for LG 22LW760V.AEU
- Page 1 INSTALLATION MANUAL LED TV* Please read this manual carefully before operating your set and retain it for future reference. LX76** LW76** www.lg.com...
-
Page 2: Table Of Contents
INTRODUCTION - USB Download Menu EZ-MANAGER WIZARD LANGUAGE & COUNTRY SELECTION - Automatically for Setup - Manually for Setup - USB LG Smart Install Utility INSTALLATION MENU INTRODUCTION LG HOTEL MODE - Hotel Mode Operation - Power On Status - Volume... -
Page 3: Location And Function Of Controls
LOCATION AND FUNCTION OF CONTROLS LOCATION AND FUNCTION OF CONTROLS Parts and Button Screen Remote control and Intelligent sensors Power Indicator Intelligent sensor - Adjusts the image quality and brightness based on the surrounding environment. Joystick Button - This button is located below the TV screen. NOTE You can set the power indicator light to on or off by selecting General in the main menus. -
Page 4: Led Clock Connection
LOCATION AND FUNCTION OF CONTROLS LED Clock Connection (Except for LW76**) CLOCK This TV can be connected to a LED Clock via the port. CLOCK LED Clock (*Not Provided) -
Page 5: Ezmanager
EZMANAGER EZMANAGER • Image shown may differ from your TV. • INTRODUCTION The Pro:Centric Platform enables you to simply install, manage and use guest-centric solutions. The default Domain “procentric.local” and IP Server Address are needed to be registered in DNS TV will contact the IP Server using the default Domain “procentric.local” via IP on server search page. -
Page 6: Language & Country Selection
EZMANAGER LANGUAGE & COUNTRY SELECTION (Except for Iran) - Please select the Language and Country. Some countries need to select the Time Zone. (Only Iran) - Please select the Language. -
Page 7: Automatically For Setup
EZMANAGER Automatically for Setup From the TV Configuration Options screen, you can choose how to proceed with the configuration of this TV. Whether you will configure the TV for Pro:Centric operation via the wizard or use a USB memory device to configure the TV, you may first wish to set the Room Number on the TV. - Page 8 EZMANAGER This step automatically searches for the Pro:Centric Server. If was found the Pro:Centric data channel, select the ‘NEXT’ .
- Page 9 EZMANAGER Downloading the Pro:Centric application files takes few minutes. After the installation is completed, the following screen will be displayed.
-
Page 10: Manually For Setup
EZMANAGER Manually for Setup Select a Label and/or enter the Room Number using the numeric keypad on the remotes or using the virtual keyboard on the TV screen. To continue, move and select ‘NEXT’ . Please select the ‘MANUAL PRO:CENTRIC’ . - Page 11 EZMANAGER Configure the appropriate Pro:Centric settings in the TV.
- Page 12 EZMANAGER Downloading the Pro:Centric application files takes few minutes.
- Page 13 EZMANAGER After the installation is completed, the following screen will be displayed.
-
Page 14: Usb Lg Smart Install Utility
EZMANAGER USB LG Smart Install Utility Select the ‘USB CONFIGURATION’ → ‘TV MANAGER’ . - If you have USB Memory for “LG_DTV” or “lg_dtv” folder, this step shows the USB file list for downloading the items. - Page 15 EZMANAGER...
- Page 16 EZMANAGER Downloading the Pro:Centric application files takes few minutes. After the installation is completed, the following screen will be displayed.
-
Page 17: Installation Menu
The abundant functions for Hotel TV linked with software installation can be projected on OSD as ‘Installation Menu’ . The wide range of hotel features can be performed simply on additional window to enhance the LG hotel TV’s easy installation and convenient operation for Hotelier and System Integrators. -
Page 18: Lg Hotel Mode
INSTALLATION MENU LG HOTEL MODE button to select the LG HOTEL MODE SETUP. Use the Use the ‘OK’ button and then button to select Hotel Mode Operation. - When ‘Hotel Mode Operation’ is set to Yes (Work), all functions of Hotel Mode apply. -
Page 19: Volume
Operation’ will be worked by below. IR Operation y Decide whether work the LG remote control or not. - When ‘IR Operation’ is set to 'Normal' , all remote keys are available. - 'Use PWR Only' makes block all remote keys except power key. -
Page 20: Limited Mode
INSTALLATION MENU Limited Mode - Configure TV function’s limitation. When selected to ‘Yes’ , following sub-menus will be worked by below. Setup Menu - Decide to enter 'Setup’ Menu’ as ‘Yes’(Enter possible) or ‘No’(Enter impossible) Programme Change y Decide to change channel or not by setting ‘Program Change' as ‘Yes’(Change Possible) or ‘No’(Change Impossible) when present source is TV. -
Page 21: Power On Default
INSTALLATION MENU Power On Default - Set the channel to display and Volume Level, etc. when turn on power in AC Power On or Stand-by status. - Set to Yes(Work) or No(Do Not Work). - When ‘Power On Default’ is set to No, it is not applied to the subordinate Input, Programme, A/V Setting, Aspect Ratio menu. -
Page 22: Network
INSTALLATION MENU NETWORK button to select the NETWORK. Use the MAC Address - Displays the MAC address (not customizable). Network Setting One-click network connection - Connects easily to a wired/wireless network. - Network Connection to connect to an available network automatically. Follow the prompts on the TV. To connect to a network through Set Expert - For use in special circumstances such as in offices (in cases where a static IP is used). -
Page 23: Ip Stream Control
INSTALLATION MENU IP Stream Control Audio PTS Offset - Controlling output stream timing of audio. - You can set the '-500~500' (Change step is -10 or +10) Video PTS Offset - Controlling output stream timing of video. - You can set the '-500~500' (Change step is -10 or +10) IGMP - You can set IGMP version. -
Page 24: Pro:centric
INSTALLATION MENU PRO:CENTRIC button to select the PRO:CENTRIC. Use the Mode - Sets whether or not enable Pro:Centric and the service method . - You can set to Off, Configuration Only, Flash(Except for Iran), GEM or HTML using the button . The default value is Off;... -
Page 25: Media Type
INSTALLATION MENU Media Type - Sets the medium type to RF or IP. The default value is RF. • Data Channel Freq(KHz) • - Sets the RF frequency at which the Pro:Centric data is received. • Data Channel Type • - Sets the RF modulation type to DVB-T or DVB-C. -
Page 26: General
INSTALLATION MENU GENERAL Configuration Setup Select RCU - It is a mode to set whether to use Select RCU or not. When ‘Select RCU’ is set to ‘Enable’ , You can adjust ‘Number of RCU’ menu. Number of RCU - It is a mode to set Number of RCU. Number of RCU value range 1~9. - Page 27 INSTALLATION MENU RS232 DC Power Outlet (Except for LW76**) - It is a mode to decide whether to output DC or not for power supply to IB Box in Installation Menu. We offer a output terminal in one Pin of RS232C Jack for the use of communication. - 5 V DC Power Outlet and 12 V DC Power Outlet must operate mutually exclusively.
- Page 28 INSTALLATION MENU DTV Programme Update - It is a mode to set whether to update DTV programme automatically or not. When DTV Programme Update is set to ’Auto’ , the function to update TV’s programme map according to dtv programme’s stream information.
-
Page 29: External Speaker
INSTALLATION MENU External Speaker Volume Control - Selects the volume control method of an external speaker. You can select ‘Off’ , ‘Int Variable’ , ’ Fixed.’ , ’Ext Variable’ by < > pressing button. Ext Variable uses the External Vol Up/Down Control Line to change the volume up to 1 Watts. Int variable is linked to the main volume OSD and change the volume 0 - 1 Watts. -
Page 30: Hcec Setup
CEC Mode - You will have 3 modes to choose [Default], [HCEC] and [TVLink-CEC]. - If [Default] is selected, you can use SIMPLINK which is provided in LG TV. Also you can enable and disable SIMPLINK through SIMPLINK MENU. - If [HCEC] is selected, you can use TVLink-HCEC Protocol. For more detailed information, please refer to TVLink-HCEC Protocol document) - If [TVLink-CEC] is selected, TV will not directly work for key input except for power key. -
Page 31: Clock Setup
INSTALLATION MENU Clock Setup Clock Display (Except for LW76**) - You can select ‘YES’ or ‘NO’ by pressing button. - After selecting ‘YES’ , you can see the LED Clock TV. Dimming Standby (Except for LW76**) - Standby Dimming value Range : 0~15 Dimming PowerOn (Except for LW76**) - PowerOn Dimming value Range: 0~99 Clock Source... -
Page 32: Password Change
INSTALLATION MENU Password Change - To ensure more security, Password can be changed by installers’ own design. button to select the CHANGE and then press the OK button. Use the Enter four digit password. Input the password again for confirmation. PreLoaded App If you want to use a particular app, you can choose from the menu. -
Page 33: Media Share
INSTALLATION MENU MEDIA SHARE ► You can setting Whether to use for “SmartShare” SmartShare - Smart Share enables DLNA function. If this value is enabled, TV act as Digital Media Player (DMP) and display Digital Media Service(DMS) contents through Smart Share app. Screen Share - Screen Share enables WiFi p2p functions such as Miracast and WiDi. -
Page 34: Bluetooth Sound Sync
TV and user can hear the sound of player through the TV. - Supported device : Mobile device based on Android (higher than v4.4 Kitkat) / iOS » support the lower than v4.4 (Kitkat) on the LG mobile device based on Android - Supported version : Higher than Bluetooth 3.0... -
Page 35: Tv Manager
INSTALLATION MENU TV MANAGER USB Download Menu * USB Cloning : An Installer can quickly set up and clone multiple TV sets at a property. These cloned TVs will all have the same Master TV Setup: Public Display Mode Installation Menu settings, User A/V settings and the Channel Map. This newer procedure significantly decreases the installation time that would be necessary if the standard RS-232C method were used instead. - Page 36 INSTALLATION MENU Ez Download - Ez Download is a function that enables users to download the desired items all at once, such as EPK (software update file), TLL (see Export Clone File descriptions for more information regarding file types), Logo Image, etc (TLX, MICOM for Pro:Centric).
- Page 37 INSTALLATION MENU Logo Image Download - If there are more than two USB Memory Device, It is possible to select the USB. - The download sequence is Logo Image Download -> Select Image -> UPDATE. NOTE Splash Image update function supports only JEPG,BMP format file of less than 8 MB filesize. We recommend you that splash image resolution match the TV`s panel resolution.
- Page 38 INSTALLATION MENU Update TV Software - This feature update EPK of TV through the hex file in USB. The target file is located in \LG_DTV folder. - If there are more than two USB memory Device, It is possible to select the USB. - The download sequence is Update TV Software ->...
- Page 39 INSTALLATION MENU Update Micom Software - This feature update MICOM of TV through the hex file in USB. The target file is located in \LG_DTV folder - If there are more than two USB memory Device, It is possible to select the USB. - The download sequence is Update Micom Software ->...
- Page 40 INSTALLATION MENU Import Clone File - Once the internal TV data and its channel map information is written to the USB memory card, the user can start “Import Clone File” process with the data file generated and stored in USB memory card. As previously warned in “Export Clone File”...
- Page 41 INSTALLATION MENU Export Clone File - "Export Clone File” must be done first before “Import Clone File” process, as it generate the file to be used in “Export Clone File”. While writing is in process, the user must not turn TV off nor unplug the USB memory card. The steps in “Export Clone File”...