WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Toshiba shall not be liable for any damages, losses, expenses or costs, if any, incurred in connection with or as a result of use of any information or data provided herein.
IMPORTANT NOTICE User's Guide Contents: Install Autodesk DWF Viewer Internet Explorer Settings Operating Environment Functions Provided on Each Drawing Page Using with Network Install Autodesk DWF Viewer Autodesk DWF Viewer is necessary to view drawings and to activate the functions of this system. Please download and install.
Page 4
[My Computer (right-click)] - [Properties] 2. Internet Explorer setting [Tools] - [Internet Options]...
for Windows Vista Operating Environment : Pentium III or higher recommended Monitor : 1024 x 768 or higher resolution recommended Mouse : A mouse with wheel recommended : Microsoft Windows 2000 SP4 / XP / Vista Browser Microsoft Internet Explorer 6.0 / 7.0 Drawing viewer : Autodesk DWF Viewer 6.0 / 7.0 * Use the software following respective license terms and conditions.
Page 7
Functions Provided on Each Drawing Page Parts Information Reference Function When the character string of a part on the drawing is clicked, its information is popped up at the location. You can get any parts information immediately on the screen without referring to the maintenance parts list. Parts Search Function You can search any part within the displayed drawing or within the whole schematic diagram/board view by specifying a location number.
Page 8
Using with Network PRECAUTION To use ZEUS Service Manual Ver.2 with network, the file-path names written on the source files of each ZEUS Engine Program Ver.2 and ZEUS Service Manual Ver.2 are to be modified. Perform the procedure described below. Preparation 1.
Page 9
Procedure of File-Path The zeusFPch is the exclusive program to exchange the file-path names written in both source files of ZEUS Manual and ZEUS Engine program into those applicable to the network use. 1. Whenever changing the file-path of both ZEUS Engine Program and ZEUS Service Manual to use with network, pay the attention to set the "Exchange to"...
Page 10
Run the zeusFPch and set "Exchange to" by referring to the examples below. Example 1 : In the "Exchange to" column shows the relation between ZEUS Service Manual and ZEUS Engine Program. ../ counts the relation between. Thus in this case, it must be ../../zeus/ (2 counts). Example 2 : In this case, it must be ../../../zeus/ (3 counts).
Page 11
2. Run the zeusFPch to change the path in the ZEUS Engine Program Ver.2. 3. Set ZEUS Engine Program in the created folder in the server to the "Target Folder", and then press "START". (This procedure is one time only)
Page 12
4. Run the ZeusFPch to change the path in the ZEUS Service Manual Ver2. 5. Set unzipped ZEUS Service Manual in the created folder in the server to the "Target Folder", and then press "START". (This procedure is required whenever placing service manual.)
Page 13
Confirmation Confirm that service manual on the server can be operated normally by client PC. Note: In case of accessing the ZEUS Manual through WEB site, the small pop-up window appears at the left bottom corner on the screen whenever searching the location links. This is not malfunction.
Page 14
Through WEB, ver. 6.5 has been released but with it, the linking function in this manual may not work properly. If ver. 6.5 has been installed, uninstall it and reinstall ver. 6.0. To get ver. 6.0, click the icon, or contact to the nearest Toshiba Service Centre for further assistance. Freezing windows opened (Cannot close the open windows) This may happen occasionally.
Page 15
The real cause has not been found yet but with this condition, nothing disturbs the service manual operation. Continue to use by operating the windows. Precaution when opening the diagrams While opening the diagrams, the menu in the left frame changes its color to GRAY. This is an indication that the viewer is processing.
Corporation recognizes environmental protection as a key management tasks, and is doing its utmost to enhance and improve the quality and scope of its environmental activities. In line with this, Toshiba proactively promotes Green Procurement, and seeks to purchase and use products, parts and materials that have low environmental impacts.
LEAD-FREE SOLDER This product is manufactured using lead-free solder as a part of a movement within the consumer products industry at large to be environmentally responsible. Lead-free solder must be used in the servicing and repair of this product. WARNING: This product is manufactured using lead free solder.
SAFETY INSTRUCTION WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" INSTRUCTIONS BELOW. Safety Precaution WARNING: SERVICING SHOULD NOT BE ATTEMPTED BY ANYONE UNFAMILIAR WITH THE NECESSARY PRECAUTIONS ON THIS RECEIVER. THE FOLLOWING ARE THE NECESSARY PRECAUTIONS TO BE OBSERVED BEFORE SERVICING THIS CHASSIS.
Page 19
6. Always use the replacement parts specified for the particular model when making repairs. The parts used in products require special safety characteristics such as inflammability, voltage resistance, etc. therefore, use only replacement parts that have these same characteristics. Use only the specified parts when the mark is indicated in the circuit diagram or parts list.
Page 20
Resistance values in orms ( ). V: Voltmeter or oscilloscope (r.m.s. or peak reading) Input resistance : Input capacitance : 200 pF Frequency range : 15 Hz to 1 MHz and d.c. respectively Note: Appropriate measures should be taken to obtain the correct value in case of non sinusoidal waveforms.
- for d.c. : = 1.0 V Note: The limit values of = 0.35 V (peak) for a.c. and = 1.0 V for d.c. correspond to the values 0.7 mA (peak) a.c. and 2.0 mA d.c. Product Safety Notice Many electrical and mechanical parts in this chassis have special safety-related characteristics.
SAFETY INSTRUCTION Handling the LCD Module Safety Precaution In the event that the screen is damaged or the liquid crystal (fluid) leaks, do not breathe in or drink this fluid. Also, never touch this fluid. Such actions could cause toxicity or skin irritation. If this fluid should enter the mouth, rinse the mouth thoroughly with water.
Page 23
because any impact can adversely affect the performance. Also use caution when handling the polarized screen because it can easily be damaged. 3. If the panel surface becomes soiled, wipe with cotton or a soft cloth. If this does not remove the soiling, breathe on the surface and then wipe again.
Page 24
6. CMOS-LSI circuitry is used in the LCD module, so avoid damage due to static electricity. When handling the module, use a wrist ground or anchor ground. 7. Do not expose the LCD module to direct sunlight or strong ultraviolet rays for an extended period of time.
Page 25
9. Do not disassemble the LCD module. Such actions could result in improper operation. 10. When transporting the LCD module, do not use packing containing epoxy resin (amine) or silicon resin (alcohol or oxim). The gas generated by these materials can cause loss of polarity.
Page 26
POWER U01A MAIN WOOFER U04A 3D-IF TOUCH SENSOR 3D-I/R 3D-I/R...
SCHEMATIC DIAGRAM Precaution WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION" FOR DIRECT VIEW CTV ONLY, "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" OF THIS MANUAL. CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
Page 31
Unless otherwise noted in schematic, all capacitor values less than 1 are expressed in µF, and the values more than 1 in pF. All capacitors are ceramic 50 V, unless otherwise noted as the following marks. = Electrolytic capacitor = Mylar capacitor 3.
ADJUSTMENT Service Mode Entering to Service Mode 1. Press any button on TV. The white LED turns 2. Press button once on remote control. ↓ 3. Press button again and hold button down. ↓ Service Mode display 4. While holding the button, press MENU button on TV set.
Page 188
Displaying the Adjustment Menu Press MENU button on TV. Service Mode Press ↑ ↓ Press Adjustment Mode...
Page 189
Key Function in the Service Mode The following key entry during display of adjustment menu provides special functions. CAUTION: Never try to perform initialization unless you have changed the memory IC. button (on remote control) Test signal selection (on TV or remote control) Selection of the adjustment items Change of the data value Volume...
Page 190
[ SERVICE MODE ] ADJUSTING ITEMS IN THE SERVICE MODE: Item Name of adjustment R-CUT RED CUTOFF G-CUT GREEN CUTOFF B-CUT BLUE CUTOFF R-DRV RED DRIVE G-DRV GREEN DRIVE B-DRV BLUE DRIVE BRTC BRIGHTNESS CENTER COLC COLOR CENTER UVTT BASE BAND TINT CNTX CONTRAST MAX MOID MODEL ID...
Page 191
Pressing of VOLUME +/- button will change the value of data in the range from 00H to FFH. The variable range depends on the adjusting item. Convert from Bit (Binary) to Hex The table for converting from bit (D7-D0) to hex (0x**). BIT (Binary) High nibble Low nibble...
3) Change MOID data into MODEL ID to initialize by pressing + or -, refer to "MODEL ID TABLE". For example, if initializing 40WL768, change MODEL ID into "0x41". Note: MODEL ID is hex value. 4) Press any button on TV. The white LED turns on.
Panel Inch Panel Model ID Panel Option Data Model Name Size ID Vendor ID (HEX) Vendor (OPT5) (HEX) (HEX) (HEX) 40WL768G/768B/ 0x41 SAMSUNG 0x0e 0x06 0x00 768F/768N/768R 46WL768G/768B/ 0x42 SAMSUNG 0x0a 0x06 0x00 768F/768N/768R 55WL768G/768B/ 0x43 SAMSUNG 0x0c 0x06 0x00 768F/768N/768R Initializing Data setting flowchart after replacing the Signal Unit Test Signal Selection...
Every pressing of button on the remote control changes the built-in test patterns on screen as described below in Service Mode. Picture Signal Red raster Green raster Blue raster All Black All White Self Diagnostic Function 1. Press "9" button on remote control during display of adjustment menu in the Service Mode.
Page 195
2. During diagnosis, the following displays are shown. * Self check displays and items are subject to the models. Item Explanation/Data Format 1 Panel Vendor Panel Vendor ID. Display 1 byte data. (Hex) 2 Panel Inch Size Panel Inch Size ID. Display 1 byte data. (Hex) 3 Factory Test Status Optional Data Bits that can be used by factory.
Page 196
11 TS IC Status Touch Sensor IC status OK: Normal NG: Failure 12 TS IC Rev Touch Sensor IC Revision. Display 1 byte data. (Hex) 13 Bus Errors IIC-BUS status. None is normal. "SCL-GND" (Red indication) : SCL-GND short circuit "SDA-GND"...
Page 197
Item Explanation/Data Format 1 TV Model Display model name strings 2 TV Model ID Model ID indicating TV size and model type Display 1 byte data. (Hex) 3 Media Player Version Version information of Music and Movie Player. 4 Boot Code Version Version information of boot code.
Page 198
Display 1 byte data. 14 TR5 EEPROM Version Version information of TR5 EEPROM Display 1 byte data. 15 A/D Adjust COMP A/D adjustment status for Component input. OK : A/D adjustment is set correctly. NG : A/D adjustment is not set correctly. –...
Setting Hotel Mode Hotel Mode allows the customized settings for following hotel options according to various hotel requirements. Enable/Disable all Front Panel keys. Enable all Front Panel keys except for Input Selection key. Enable/Disable the remote control. Disable access to all Setup menu items except for Language Setting. Disable access to the Setup menu (grayed out).
Page 200
on selected items as follows; OPT2 OPT2 FUNCTION DESCRIPTION (Normal) D7 (bit7) Enable mode that TV standby will be Enable Disable appeared in forced when turning the main (This function is ignored power ON when D6 is set to 1.) D6 (bit6) Enable mode that TV On will be appeared Enable...
Page 201
number will be appeared in forced when turning the main power ON D6 (bit6) ~ POS or VIDEO program number 0 ~ 127 [decimal] D0 (bit0) POS number: 0 ~ 99 VIDEO number: 100 ~ 127 (DTV = 100, VIDEO = 101, VIDEO = 102..) 100 is used as ATV when DTV option is disable.
Page 202
1. Press any button on TV. The white LED turns 2. Press button once on remote control. ↓ 3. Press button again and hold button down. ↓ (Hotel Mode Settings menu) 4. While holding the button, press P button on TV set. 5.
Page 203
6. Press buttons to select the item, and then press buttons to change the setting. 7. Press [Exit] button to finish Hotel Mode setting. Settings in "Hotel Mode Settings" menu Hotel Mode Corresponding Options Description Value Setting Option Data Hotel Mode Disable OPT2, D0 Enable...
Page 204
(Except except for Language Setting Language) Max Volume 0 ~ 100 Limited maximum volume level VOLX, D7 ~ D0 0x00 0x64 Change TV Tunes to the last channel or OPT6, D7 POS/VIDEO input viewed when the TV is turned TV tunes to preset "POS/VIDEO"...
Page 205
Selectable Standard Force Picture Mode to Standard Picture" is On) when the TV is turned on Movie Force Picture Mode to Movie when the TV is turned on Change TV Disabled TV returns to previous Standby/On OPT2, D7 ~ D6 Power State when the main power is applied...
Page 206
Programme (position) System Colour System Programme Skip Channel Manual Fine Tuning Label Saving the Hotel Mode Settings of the TV to USB device 1. Configure the hotel mode settings via Service Mode or the Hotel Mode Settings menu. 2. Enter Hotel Clone menu by following steps a - d. a.
Page 207
(Hotel Clone menu display) d. While holding the button, press P button on TV set. 3. Press buttons to select "TV to USB". 4. Insert a USB device and press OK to copy the settings to the USB device. 5. After copy is completed successfully and the message is shown, remove the USB device.
4. After the copy is completed successfully, the message is shown and the set reboots automatically. 5. Remove the USB device. 6. If the copy is not completed, an error message is shown and the set does not reboot. Repeat from step-a again, or repeat the steps of saving from TV to USB device. LED Indications The LEDs on the TV (at the bottom of the TV) indicate the TV's status, as described below.
Page 209
TV Software Upgrade - While Watching TV 1. Turn the TV on. 2. Prepare a USB device having the upgrade software data. 3. Insert the USB device into the upper USB slot on the right side of the TV. The following message is shown. 4.
Page 210
TV Software Upgrade - from Boot Up 1. Prepare a USB device which having the upgraded software. 2. Turn the TV on. 3. Insert the USB device into the upper USB slot on the right side of the TV. Then following message is displayed. 4.
Page 211
13. After the TV is turned on, perform a factory reset by selecting "Reset TV" in the Setup Menu. Special LipSync Setting for Game Mode Only 1. Change the TV Input to HDMI1 to enable "HDMI Settings" MENU. 2. Select MENU > PREFERENCES > AV Connection > HDMI Settings. The MENU screen below will be displayed.
Page 212
8. Change the setting by < or > button on the remote. LipSync FUNCTION Fixed Delay value for all modes (default) Small Delay value only in Game Mode 9. Press Exit button to finish "HDMI Settings" MENU. Note: Do not change the "HDMI Input Mode" [Mode1/ Mode2/ Mode3]. LipSync [Off/On] setting is commonly applied to all HDMI Inputs.
Page 213
PROCEDURE FOR TAKING OFF THE LCD PANEL Removal of the Back Cover Open the lid cover holding the AC Power Code. Release the AC Power Code from the wire band inside the lid cover. Remove the Back Cover. Fig.1 Removal of the Back Cover Removal of the PCBs Take off the two Speaker Assy's from the chassis, and disconnect the speaker cable from Main PCB.
Page 214
Fig.2 Removal of the PCBs Taking off the LCD Panel Prior to taking off the LCD Panel, attach the two rails as shown in Fig.3. <Caution> RMA is not accepted if the rails are not attached. Release the two Slider Locks at the left and right side as shown in Fig.4, and remove them. Lift up the base edge of the LCD Panel.
Page 215
Fig.3 Attach the rails to prevent the LCD Panel from accidental distortion Fig.4 Slider Lock Fig.5 How to take off the LCD Panel...
Page 216
TECHNICAL BULLETIN File Name Title issuing date...
PANEL IDENTIFICATION Panel Identification If the several panels are alternatively used in the same model without amending the model name, the identification marking will be shown at the last digit of the set serial number on the specification label on the back cover. In servicing, do not alter the panel because several setting and parts are different.
PARTS LIST Precaution WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "SAFETY PRECAUTION" "PRODUCT SAFETY NOTICE". CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
Page 221
: Variable Resistor : Electrolytic : Metal Film : Fusible Resistor All CD and PF capacitors are ±5 %, 50 V and all resistor, ±5 %, 1/6 W unless otherwise noted.
Page 222
PARTS LIST ↓Select Block : Search 1 / 1 Jump Page : Jump Location : Search Parts No. :...
FUNCTION AND OPERATION Tuning the Television for the First Time Before switching on the television, put your decoder and media recorder, if applicable, to Standby. To set up the television, use the buttons on the remote control.