Advertisement
Others in the workplace should keep a safe distance from the drill, especially when it is in operation.
!
Keep the work area as childproof as possible by using padlocks and master switches.
!
Keep drill bits clean and sharp for best and safest performance. Follow the instructions for lubrication and changing accessories.
!
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
!
Locate drill in a suitable work area and keep area clean and tidy and free from unrelated materials. Ensure that there is adequate lighting.
!
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
!
Secure unstable workpieces with a clamp, vice or other adequate holding device.
!
! Avoid unintentional starting.
DO NOT use the drill for a task that it is not designed to perform.
%
DO NOT allow untrained persons to operate the drill.
%
DO NOT get the drill wet or use in damp or wet locations or areas where there is condensation.
%
DO NOT operate the drill if it is damaged.
%
DO NOT use drill in an area where paint fumes, solvents or flammable liquids pose a potential hazard. Keep flammable material away from
%
the drill when operating. Flammable waste, such as wipes or cleaning rags, must be placed in a closed metal container and disposed of correctly.
DO NOT exceed the rated capacity of the drill.
%
DO NOT operate the drill if any parts are missing as this may cause failure and/or personal injury.
%
DO NOT leave the drill operating unattended.
%
DO NOT operate the drill when you are tired or under the influence of alcohol, drugs or intoxicating medication.
%
DO NOT pull the cable from the power supply.
%
When not in use switch off the drill, remove the plug from the power supply and do not leave until the chuck has come to a complete stop.
!
2. DESCRIPTION
These variable speed drills are suitable for light industrial, agricultural and woodworking applications. Both drills are fitted with flip-up safety
guards and “No-Volt Release” switches which prevent accidental restart after a mains power interruption. A rack and pinion feed shaft with
preset depth control for repetitive work is also included. Work clamps, vices and mortising attachments are available for these drills, contact
your local Sealey dealer for information.
3. TECHNICAL SPECIFICATIONS
Model
Chuck Size (mm)
Spindle Nose Taper
Swing (mm)
Throat (mm)
Spindle Travel (mm)
Number of Speeds
Speed Range (rpm)
Spindle to Table - Max. (mm)
Spindle to Base - Max. (mm)
Working Table Diameter (mm)
Working Base (mm)
Overall Base (mm)
Column Diameter (mm)
Overall Height (mm)
Collar Diameter (mm)
Voltage (AC)
Motor (Watts)
Weight (kg)
4. CONTENT
4.1. Package content
Unpack the parts listed below and check to ensure they are in good condition. Any queries must be reported to your dealer immediately.
! Head Assembly
! Column with Flange
! Base
! Table
! Table Arm
! Table Bracket and Worm
!Rack and Rack Ring
GDM150B/VS
GDM200F/VS
16
MT2
MT2
218
218
178
178
83
Infinite within speed range
150 - 2300
150 - 2300
410
740
600
1195
310
310
387 x 205
387 x 205
450 x 265
450 x 265
80
1035
1630
58
230
230
650
650
77
! Feed Handles and Knobs (3)
! Pivoted Lock Handle (2 - table arm & bracket)
! Adjusting Handle with Set Screw (table)
! Bolt and Washer (table arm)
! Bolts (4 - column)
! Chuck and Key
!Arbor
16
83
80
58
81
!Speed Control Handle
! Safety Guard
! Set Screws (2 - head)
! Screw and Washer (pulley cover)
!Wedge
! Hex. Keys (2)
GDM150B/VS & GDM200F/VS - 1 - 110402
Advertisement
