Set-Up And Pre-Operation - SBI Splitz-it 5-Ton Operator's Manual

SET-Up AND pRE-OpERATION

1
2
3
4
Figure 1
Before attempting to use, familiarize yourself with all the
operating features and safety requirements of your log splitter.
(SEE FIGURE 1)
1. Wedge
2. Oil tank
3. Carrying handle
4. Supporting leg
5. Motor w/push switch
& circuit breaker
6. Rubber feet
7. Rolling wheel
bleed screw
dipstick
oil drain plug
Figure 2
6
11
5
8. 2-hand operating
THIRD ANGLE PROJECTION
hydraulic control lever
PARTS TO BE FREE OF
BURRS AND SHARP EDGES
9. Safety guard for 2-hand
MATERIAL
TOLERANCE UNLESS
OTHERWISE NOTED:
SEE BILL OF MATERIALS
operating hydraulic
0.0 ±.100 INCH ± 2.54 MM
0.00 ±.030 INCH ± 0.76 MM
control lever 0.000 ±.010 INCH ± 0.25 MM
TREATMENT
ANGLES:
NONE
0 ± 2°
10. Log pusher
0.0 ± 1.0°
THREADS CLASS 2
PRIMARY DIMENSIONS ARE IN INCHES
11. Log cradle
SECONDARY DIMEMSION ARE IN MM
SURFACE AREA
PT WEIGHT
ALL ANGLES ARE DECIMAL DEGREES
32121.68 3451644.89
UNLESS OTHERWISE SPECIFIED
wARNING
FOR YOUR OwN SAFETY, DO NOT CONNECT THE LOG
10
SpLITTER TO THE pOwER SOURCE UNTIL THE MACHINE
IS COMpLETELY ASSEMbLED AND YOU READ AND
9
UNDERSTAND THE ENTIRE INSTRUCTION MANUAL.
FOR YOUR OwN SAFETY, NEVER FORGET TO bOLT THE
wHEEL bRACkET TO THE LOG SpLITTER, LIFT THE LOG
SpLITTER bY THE HANDLES AT bOTH ENDS AND pLACE
8
IT ON A 60-75CM HIGH, STAbLE, FLAT AND LEVEL wORk
7 SURFACE.
NEVER USE THE LOG SpLITTER IF IT IS NOT IN pERFECT
ORDER OR IF IT NEEDS SERVICING. bEFORE STARTING
6
wORk, CHECk CORRECT FUNCTIONING OF ALL THE
CONTROLS (HYDRAULIC LEVER, pUSH bUTTON).
CAUTION
FAILURE TO LOOSEN THE bLEED SCREw wILL RESULT IN
AIR bEING COMpRESSED AND DECOMpRESSED IN THE
HYDRAULIC SYSTEM. CONTINUOUS AIR COMpRESSION
THIS DRAWING AND ALL INFORMATION CONTAINED HEREIN IS AND REMAINS THE PROPERTY
AND IS CONFIDENTIAL. IT IS SUBMITTED AND MAY BE USED ONLY IN CONNECTION WITH
AND/OR ITS CUSTOMERS' ORDERS. IT SHALL NOT BE DISCLOSED TO OTHERS OR COPIED
AND DECOMpRESSION wILL bLOw OUT THE SEALS OF
SPECIFIC WRITTEN CONSENT AND SHALL BE IMMEDIATELY RETURNED UPON REQUEST.
NAME
W1200 5 TON ELECTRIC
THE HYDRAULIC SYSTEM AND CAUSE pERMANENT
LOG SPLITTER
DAMAGE TO THE LOG SpLITTER.
DR BY APPD
MATT OLSEN
MDO 9/17/2010
DATE
SHEET: 6 OF 8
09/17/2010
CAUTION
DO NOT ADJUST THE MAxIMUM pRESSURE LIMITING
SCREw. THE pRESSURE LIMITING SCREw HAS bEEN
SEALED AT THE FACTORY TO pREVENT UNAUTHORIZED
ADJUSTING. RESETTING THE SCREw wILL CAUSE
THE HYDRAULIC pUMp TO FAIL TO OUTpUT ENOUGH
SpLITTING pRESSURE OR CAUSE TOO MUCH pRESSURE,
wHICH MAY RESULT IN SERIOUS INJURY, AS wELL AS
DAMAGE TO THE MACHINE.
IMpORTANT
bEFORE OpERATING THE LOG SpLITTER, THE bLEED
SCREw SHOULD bE LOOSENED bY 3-4 ROTATIONS SO
AIR CAN GO IN AND OUT OF THE OIL TANk SMOOTH-
LY. AIR FLOw THRU THE bLEED SCREw HOLE SHOULD
bE DETECTAbLE DURING LOG SpLITTER OpERATION.
bEFORE MOVING THE LOG SpLITTER, MAkE SURE
THE bLEED SCREw IS TIGHTENED TO AVOID OIL
LEAkAGE FROM THIS pOINT. (See Figure 2)
Splitz-it 5-tON electric lOg Spliter
OF ARDISAM INC.
ARDISAMS' PROPOSALS
WITHOUT ARDISAMS'
PRT NO
W1200
1
REVISION