Speaker Cords; Attaching To A Wall; Attaching To Speaker Stands - Panasonic SC-HT75 Operating Instructions Manual

Speaker cords

Attach the stickers to the speaker cords.
≥Attach the numbered stickers to the end of the speaker
cords so the numbers match the positions of the speak-
ers shown in the diagram.
1
6 5 4 3 2 1
SUBWOOFER CENTER R SURROUND L SURROUND R FRONT L FRONT
SUBWOOFER CENTER SURROUND R SURROUND L FRONT R FRONT L
6 5 4 3 2 1
L FRONT
FRONT L
6 5 4 3 2 1
SUBWOOFER CENTER R SURROUND L SURROUND R FRONT L FRONT
SUBWOOFER CENTER SURROUND R SURROUND L FRONT R FRONT L
1
6 5 4 3 2 1
≥Connect the cords to the terminals of same color so the num-
bers on the stickers match the numbers under the terminals.
≥Never short-circuit positive (i) and negative (j) speaker wires.
≥Be sure to connect only positive (red or gray) wires to positive
(i) terminals and negative (black or gray with blue stripe) wires
to negative (j) terminals.
Incorrect connection can damage the speakers.
≥After you have completed setup and connection, wind the ex-
cess cord and keep together with string.
≥The speaker nets cannot be removed.
Notes on speaker use
≥You can damage your speakers and shorten their useful life if
you play sound at high levels over extended periods.
Reduce the volume in the following cases to avoid damage.
–When playing distorted sound.
–When the speakers are receiving howling from a micro-
phone or record player, noise from FM broadcasts, or con-
tinuous signals from an oscillator, test disc, or electronic
instrument.
–When adjusting the sound quality.
–When turning the unit on or off.

Attaching to a wall

Front and surround speakers can be attached to a wall.
Attach four speaker feet to each speaker, ensuring they do not
cover the holes.
Set the speaker onto screws and slide through bracket to lock
into position.
]HT95]
Speaker feet (included)
Screw (not included)
Speaker feet
(included)
[HT75]
The method for attaching speakers to a wall is the same except
that there is only one bracket.
Note
The wall or pillar on which the speakers are to be attached should
be capable of supporting 10 kg (22 Ib.) for SB-AFC286 and 5 kg
(11 Ib.) for SB-AFC95 per screw.
30–35 mm
(1 3 ⁄ 3 ⁄
q–1 q)
16 8
Ø7.5–9.5 mm
( 19 ⁄ 3 ⁄
q– q)
64 8
7–9 mm
( 9 ⁄ 23 ⁄
q– q)
32 64
106 mm (4 11 ⁄
q)
64
Screw (not included)
Twist the vinyl tip and pull off.
Gray
Red
6
5
4
3
2
1
Black
Red
Black
Center speaker
Subwoofer

Attaching to speaker stands

Ensure the following conditions are met when you purchase your
speaker stands.
≥Observe the diameter and length of the screws and the distance
between screws as shown in the diagram.
≥The stands must be able to support over 10 kg (22 Ib.) for
SB-AFC286 and 5 kg (11 Ib.) for SB-AFC95.
≥The stands must be stable even if the speakers are in a high
position.
Attach the stands
with these holes.
1
3
2
Gray (no stripe)
Gray with blue stripe
Blue
Front speaker (left)
Front speaker (right)
Surround speaker (left)
Surround speaker (right)
5 mm ( 13 ⁄
q),
64
pitch 0.8 mm
60 mm (2
( 1 ⁄
q)
32
Plate thickness
plus 7 to 10 mm
(plus 9 ⁄ q to 25 ⁄
q)
32 64
Speaker stand
(not included)
23 ⁄
q)
64
7
RQT6183