Related Manuals for Vita-Mix BARBOSS MP
Summary of Contents for Vita-Mix BARBOSS MP
- Page 1 F O O D S E R V I C E Owner’s Manual Read And Save These Instructions BarBoss ® Drink Machine MP Maximum Performance Commercial Blender All Models...
-
Page 2: Important Safeguards
Vita-Mix blender. A rubber scraper may be used, but only when the Vita-Mix blender is not running. With the flexible rubber lid in place the accelerator tool may be used while motor is running. - Page 3 Important Safeguards Enjoy the safety of this grounded appliance. The Vita-Mix blender’s U.S. power cord comes equipped with a three-prong (grounding) plug which mates with a standard three- prong wall outlet (Figure A). This cord will vary for countries outside the United States.
- Page 4 Note on Timers: Stop mid cycle with START/STOP switch, not the ON/OFF switch. If the ON/OFF switch was used, wait 30 seconds for power to recycle and the timer to reset before resuming operation. NOTE: Switches will become sticky from use. Use a wet cloth or sponge to flush and clean in the groove around the water-shielded switches.
- Page 5 • Twist the center lid plug to fasten or remove. NOTE: Older 48 oz. (1.4 L) and 64 oz. (2.0 L) Vita-Mix container will work on the BarBoss or Drink Machine MP. The Xtreme Performance Containers will not work on older Vita-Mix Machines.
- Page 6 ® BarBoss MP & Drink Machine MP Instructions 1. Set the container on the motor base by aligning it over the centering pad anchored to the base. (Motor must be completely stopped before positioning container). Containers are not to be used for hard, dry materials. Avoid running your machine with the container empty.
- Page 7 Note: The thermal protector shuts the motor off to protect it from overheating. To restart, wait for motor to cool down with the power OFF (up to 30 minutes). When this happens, review your processing techniques and your instructions. Your recipes may be too thick or have too much material in them.
- Page 8 At times, it may be necessary to give your blades additional cleaning. An easy-to-use blade assembly removal wrench (Item #15596) may be purchased through your Vita-Mix distributor. Never attempt to take the blade assembly itself apart. This will void the warranty.
- Page 9 (or whenever your mixture requires it). It also permits you to push ingredients down around the blades while the Vita-Mix blender is running. Accelerator Tool use: • Use only with the lid in place and the center lid plug removed.
- Page 10 Care Note To ensure that you get the longest possible life from your Vita-Mix product, we recom- mend the following products, when used as directed by the supplier: Cleaning Product......
-
Page 11: Motor Base
* * Return container to motor base and firmly position the two part lid. Run machine for 30 seconds. Empty container. Repeat this step. ** Note: To prolong polycarbonate container life, Vita-Mix recommends using soaps with a low Ph balance, such as a manual pot and pan detergent. Due to the nature of polycarbonates, automatic dishwashing is not recommended. - Page 12 BarBoss MP & Drink Machine MP ® NOTE: Outside the United States and Canada, your machine may come with a different container configuration. Contact your local Vita-Mix distributor for part numbers. Item # Part #760 Accelerator tool #15578 Sound-reducing XP centering pad...
- Page 13 If you cannot fix your machine with these suggestions, technical help is available by calling 800-4DRINK4 (800-437-4654). If outside the United States and Canada, contact your local Vita-Mix distributor or phone the Vita-Mix International Division at +1(440) 782-2450 or email international@vitamix.com for a distributor in your country.
- Page 14 Vita-Mix blender is put into a sound reduction chamber that does not allow proper cooling. In the event your Vita-Mix appliance needs service or repair covered by the terms of this warranty, please call the Vita-Mix Corporation for shipping instructions. The Vita-Mix blender must be sent in original or sufficient packaging.
- Page 15 Vita-Mix Customer Service and, when the new part arrives, return the old part in the same packaging. Vita-Mix will inspect the returned part and, if defective, issue a refund for the price of the new part.
-
Page 16: Power Requirements
©2005 Vita-Mix Corporation. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopy, recording or any information storage and retrieval system without the written permission of the Vita-Mix Corporation.