Basic Operation - Siemens LR97CAQ50 User Manual And Installation Instructions

7 Before using for the first time
Configure the settings for initial start-up. Clean the ap-
pliance and accessories.
7.1 Setting an operating mode
Your appliance is set to air extraction mode by default.
To use it in circulating-air mode, you must set the oper-
ating mode.
Note: For use in circulating-air mode, you require addi-
tional Accessories.
Requirement: The appliance is switched off.
Press and hold and
1.
To set circulating-air mode (non-regenerable fil-
‒
ter), press ⁠ / until LED 2 lights up in the LED
display.
8 Basic operation
8.1 Switching on the appliance
Requirement: Align the remote control as precisely as
possible to the infrared receiver for the LED display.
Press to switch on the appliance.
▶
a The appliance starts at fan setting 2.
a The LED for the set fan setting lights up in the LED
display.
8.2 Switching off the appliance
Switch the appliance off when you are not using it.
Press to switch the appliance off.
▶
a The appliance switches off. Any functions currently
in progress are cancelled.
8.3 Selecting a fan setting
Press or ⁠ .
▶
a The LED for the set fan setting lights up in the LED
display.
8.4 Switching on intensive mode
If particularly strong odours or vapours develop, you
can use intensive mode.
so oft drücken, bis in der LED-Anzeige die LED 4
1.
für die Intensivstufe 1 leuchtet.
so oft drücken, bis in der LED-Anzeige die LED 5
2.
für die Intensivstufe 2 leuchtet.
a After approx. 6 minutes, the appliance automatically
switches to fan setting 3.
8.5 Switching off intensive mode
To select a fan setting of your choice, press
▶
8.6 Switching on the fan run-on
Press ⁠ .
▶
1
Depending on the appliance specifications
for approx. three seconds.
⁠ .
Before using for the first time en
To set circulating-air mode (non-regenerable fil-
‒
ter), press ⁠ / until LED 3 lights up in the LED
display.
To convert the electronic control back to opera-
‒
tion without the air recirculation filter, press
until LED 1 lights up on the LED display.
To save the setting, press and hold and for ap-
2.
prox. three seconds.
Or wait approx. 10 seconds until the setting is
saved automatically.
To cancel the setting, press ⁠ .
a A signal tone sounds as soon as the selected set-
ting is saved.
a LED 1 for the fan setting lights up in the LED dis-
play. LED 6 flashes for the fan run-on.
a The appliance switches off automatically after ap-
prox. 10 minutes.
8.7 Switching off the fan run-on
Press ⁠ .
▶
a This immediately stops the fan run-on.
a The appliance switches to the fan setting that was
previously selected.
8.8 Switch on automatic mode
The optimum fan setting is set automatically using a
sensor.
Press ⁠ .
▶
a In the LED display, LED 6 lights up for automatic
mode.
8.9 Switch off automatic mode
Press ⁠ .
▶
a The appliance switches to the fan setting that was
previously set.
a The ventilation is automatically ended when the
sensor detects no further change in the room air
quality.
a Automatic mode runs for a maximum of four hours.
8.10 Intermittent ventilation
With interval ventilation, the ventilation system switches
on and off in the selected setting for the selected time.
Note: This function is only available via a mobile device
with the Home Connect app.
If the interval ventilation is switched on, LED 6 continu-
ously flashes in the LED display for the interval ventila-
tion and the LED for the selected fan setting lights up.
⁠ /
1
1
7