Advertisement
Quick Links
Advertisement
Related Manuals for Verkada CB61
Summary of Contents for Verkada CB61
- Page 1 CB51 CB61 Outdoor Bullet Camera...
-
Page 2: What You'll Need
• A working internet connection • A smartphone or laptop • A Cat5 or Cat6 ethernet cable with a .2-.25 inch outside diameter (5-6.5mm) What you’ll need • 802.3af/802.3at POE Power over Ethernet (PoE) switch, or a PoE injector. For operation below -20°... - Page 3 1 CB51 / CB61 outdoor bullet camera CB51 / CB61 Outdoor Bullet Camera 1 Mount plate (pre-assembled with camera) 1 Setup guide, with 1 mounting template 1 T8, T25 Hand tool 1 22mm cable gland wrench In the box 4 Wall mounting screws...
- Page 4 Optional Cable Exit Collar Locking Screw 3/4” NPT Threaded Connection Ball Joint Lock Screw Removable Cover CB51 CB61 Overview Mount Plate Cover Collar Status LED Base Plate Base Locking Screw...
- Page 5 Use the T8 drive to loosen the set screw. Do not completely remove the screw. CB51 CB61 Connect Twist the Cover Collar near the middle of the camera to remove the outer Cover.
- Page 6 Solid blue Camera is running, connected, Insert the ethernet cable into ethernet port. Scan the QR code for easy For detailed installation instructions, camera registration and setup, or proceed to www.verkada.com/start. visit www.verkada.com/support and streaming video 10 - connect connect - 11...
- Page 7 CB51 CB61 Mounting To unlock the Mount Plate from the Base Plate, loosen the Base Locking Screw using the provided T8 hand tool. The screw should be backed out approximately .2” (5mm) from the Base Plate. Do not fully remove the screw.
- Page 8 To remove the Mount Plate from the Base Plate, twist the Mount Plate counter- Use the provided mounting template to mark Mount Plate holes. clockwise then pull the Mount Plate o of the underside of the Base Plate. For a solid material like wood or metal, drill 1/8 inch pilot holes. Drive mounting screws directly into the pilot holes.
- Page 9 Remove the cable gland from CB51 / CB61. Feed ethernet cable through the center of the Mount Plate before fully securing it to the mounting surface. Leave enough slack to safely handle the camera during cable Route the ethernet cable through the Mount Plate and ball gland installation.
- Page 10 Align mounting features on the Mount Plate with the Engage the mounting pegs and twist clockwise until you feel the camera lock mounting pegs on the backside of CB51 / CB61 Base Plate. securely in place. Once secured, tighten the T8 security screw using the provided hand tool.
- Page 11 Firmly push the rubber seal and plastic collar together. Slide the metal nut over the RJ45 connector and engage the threads on the pass-through. Slide the cable gland assembly into pass through, seating it in position. Gently tighten down the metal nut by hand. You should still be able to move the cable back and forth through the gland.
- Page 12 Push the excess ethernet cable back through the cable gland assembly. Plug in Firmly tighten the metal nut using the included wrench. the ethernet cable to the camera’s RJ45 jack. The cable should be routed straight from the cable gland into the RJ45 jack. 22 - mount mount - 23...
- Page 13 CB51 CB61 Secure To finish securing the device, align the outer Cover with the camera and push into place. The external threads on the outer Cover will meet the internal threads on the Cover Collar at the back of the housing.
- Page 14 Rotate the Cover Collar to thread the outer housing into place. The outer Cover will Use the T8 security key to tighten the set screw on the side of the Cover Collar be pulled into place and should seat against the ring when fully tightened. to increase tamper resistance.
- Page 15 CB51 CB61 Adjust Adjust your camera to the desired viewing angle. Use the online stream to confirm image orientation. Image can be flipped 180˚ online in Command.
- Page 16 Tilt To lock the camera in place, use the T25 security torx key to turn the Rotate screw on the side of stand. This will tighten the ball joint. To fully secure the device, rotate the torx handle 90 degrees and tighten the screw further.
- Page 17 +1 (833) 837-5232 support@verkada.com www.verkada.com/support...