Table of Contents
Advertisement
Quick Links
For The ON-THE-GO Pet
™
INSTRUCTION MANUAL
NO-ZIP EXCURSION PET STROLLER
PG8650NZ
Interior Dimensions:
26"L x 15"W x 20"H
To see our full line of products, visit us online at: www.petgearinc.com
CUSTOMER SERVICE HELP DESK
customerservice@petgearinc.com
Toll-Free 877-752-9123 - Eastern Standard Time 8am-3pm, Monday through Friday
1
Advertisement
Table of Contents
Related Manuals for Pet Gear PG8650NZ
Summary of Contents for Pet Gear PG8650NZ
- Page 1 For The ON-THE-GO Pet ™ INSTRUCTION MANUAL NO-ZIP EXCURSION PET STROLLER PG8650NZ Interior Dimensions: 26"L x 15"W x 20"H To see our full line of products, visit us online at: www.petgearinc.com CUSTOMER SERVICE HELP DESK customerservice@petgearinc.com Toll-Free 877-752-9123 - Eastern Standard Time 8am-3pm, Monday through Friday...
-
Page 2: Parts List
PARTS LIST Check that you have all the parts shown BEFORE assembling your product. If any parts are missing, call Customer Service. 2-Front Wheels Stroller 2-Back Wheels Removable Internal Liner N0-ZIP EXCURSION PET STROLLER • PG8650NZ... - Page 3 Repeat on other side. When finished it should look like Figure C. Outside Inside To Remove Back Wheels : Hold down the lock/release button (Figure A) and pull wheel off. Lock/Release Button N0-ZIP EXCURSION PET STROLLER • PG8650NZ...
-
Page 4: Front Wheel Assembly
Hold down wheel release button and pull wheel out. STROLLER ASSEMBLY When all wheels are on stroller, carefully place the stroller on all 4 wheels and begin to pull up on handle to unfold the stroller shown in Figure F. N0-ZIP EXCURSION PET STROLLER • PG8650NZ... - Page 5 As you unfold the stroller, straighten the side latches until they lock in place shown in Figures G and H. You will hear a click when the slide latches are engaged. To adjust handlebar, push in buttons located on each side of the handlebar and adjust to comfort shown in Figure I. N0-ZIP EXCURSION PET STROLLER • PG8650NZ...
- Page 6 Figures L and M. To close the back of your stroller, clip the rear door into the back of the stroller. Release Button N0-ZIP EXCURSION PET STROLLER • PG8650NZ...
- Page 7 TO ASSEMBLE BACK TRAY Step 1. To assemble the back tray, align the holes on the front of the tray with both of the knobs on the stroller, and secure into place by pushing forward, then down. N0-ZIP EXCURSION PET STROLLER • PG8650NZ...
- Page 8 Step 1. Fold down handlebar by pushing in the buttons ure Q.) until latch disengages. located on each end of the handlebar shown in Figure P. TO FOLD/PACK UP STROLLER Step 3. Fold sides inward and push forward shown in Figure R. N0-ZIP EXCURSION PET STROLLER • PG8650NZ...
-
Page 9: Wheel Maintenance
• Clean the rear wheel assembly and the rest of the frame with warm, soapy water; clean off with warm water and dry thoroughly. • NOTE: Do not lubricate brake components or swivel locks. N0-ZIP EXCURSION PET STROLLER • PG8650NZ... -
Page 10: Replacement Parts
Not intended to be used as a restraining device for aggressive or dangerous animals that dig, chew or paw aggressively. Do not leave your pet unattended. PET GEAR is not liable for any damage caused by aggressive, destructive, immature or untrained animals. Do not use near an open or exposed flame. Failure to follow these warnings and the instructions could result in serious injury or death.