Related Manuals for Tanda TX7300
Summary of Contents for Tanda TX7300
- Page 1 TX7300 Addressable Sounder Strobe Installation and Operation Manual TANDA UK Technology Copyright ©2015, All right reserved.
- Page 2 For more information please visit the website at www.recyclethis.info EN54 Part 3 Compliance TX7300 Addressable Sounder Strobe complies with the requirements of EN 54-3:2001 + A1:2002 + A2:2006 EN54 Standard Conformity Information 0832...
-
Page 3: Table Of Contents
TX7300 Addressable Sounder Strobe Installation & Operation Manual Table of Content 1 Introduction ..............................4 1.1 Overview ..............................4 1.2 Feature and Benefits ........................... 4 1.3 Technical Specification ........................4 2 Installation ..............................5 2.1 Installation Preparation ........................5 2.2 Installation and Wiring ........................5 3 Sounder Strobe Configuration ........................ -
Page 4: Introduction
1 Introduction 1.1 Overview The TX7300 Addressable Sounder Strobe is alarm warning device used to notify persons in the vicinity of the occurrence fire emergency in order the person to take appropriate measures. The unit adopt multi-application device starting from the types, parameters and wiring layout in single unit. The TX7300 can change into different alarm warning types such as sounder-strobe type, sounder type or strobe type using programming tool. -
Page 5: Installation
TX7300 Addressable Sounder Strobe Installation & Operation Manual 2 Installation 2.1 Installation Preparation This alarm warning device must be installed, commissioned and maintained by a qualified or factory trained service personnel. The installation must be installed in compliance with all local codes having a jurisdiction in your area or BS 5839 Part 1 and EN54. -
Page 6: Sounder Strobe Configuration
TX7300 Addressable Sounder Strobe Installation & Operation Manual 3 Sounder Strobe Configuration 3.1 Preparation The TX7930 handheld programmer is used to configure sounder strobe soft address and parameters. This tools are not included, must be purchased separately. The programmer is packed with twin 1.5V AA battery and cable, ready for usage once received. -
Page 7: Single And Dual Address Mode
TX7300 Addressable Sounder Strobe Installation & Operation Manual 3.3 Single and Dual Address Mode Single address is commonly used to program immediate Evacuate tone while the dual address used for programming Pre-alarm and Evacuate tones respectively in a given period of time. -
Page 8: Typical And Saving Mode
TX7300 Addressable Sounder Strobe Installation & Operation Manual 3.4 Typical and Saving Mode When Sounder-Strobe is configured to Saving Mode the recommended wiring is loop powered [Figure 2] within the limit of 20 units per loop and subject to the total calculated current load in particular loop. -
Page 9: Tones Selection
TX7300 Addressable Sounder Strobe Installation & Operation Manual Read Description 1. Read ⑤ Strobe: Visible signal only ① Single ② Dual 2. Write ⑥ Sound: Audible signal only ③ Typ ④ Saving 3. R/W Config Note: Select 5 and 6 for both ⑤Strobe... -
Page 10: Read Configuration
TX7300 Addressable Sounder Strobe Installation & Operation Manual 1. Attach the programming cable to 1 and 6 Terminals of sounder strobe. Press “Power” to switch-on the unit. 2. Switch-on the programmer, then press button “4” to enter to Setting mode (Figure 14). The programmer will display the actual configuration after few seconds. -
Page 11: General Maintenance
TX7300 Addressable Sounder Strobe Installation & Operation Manual 4 General Maintenance 1. Inform the suitable personnel before conducting the maintenance. 2. Disable the alarm warning device on the control panel to prevent false alarm. 3. Do not attempt to repair the circuitry of the alarm warning device, it may affect the operation to respond to a fire condition and will void the manufacturer’s warranty. - Page 12 TX7300 Addressable Sounder Strobe Installation & Operation Manual 2. Tone 16 – Volume dB(A) Typical Mode dB(A) Saving Mode dB(A) Horizontal Plane Vertical Plane Horizontal Plane Vertical Plane Angle Max27.5V Min 20V Max27.5V Min 20V Max27.5V Min 18V Max27.5V Min 18V 15°...
-
Page 13: Limitation Of Sounder Strobe Device
TX7300 Addressable Sounder Strobe Installation & Operation Manual Limitation of Sounder Strobe Device The alarm warning device cannot last forever. In order to keep the alarm warning device working in good condition, please maintain the equipment continuously according to recommendations from manufacturers and relative nation codes and laws.