SNOWJOE sunjoe CJ602E-RED Operator's Manual

SNOWJOE sunjoe CJ602E-RED Operator's Manual

15-amp electric wood chipper + shredder

Advertisement

Quick Links

A Division of Snow Joe
, LLC
®
IMPORTANT!
Safety Instructions
All Operators Must Read These
Instructions Before Use
Always follow these safety guidelines. Failure to do so may
result in serious bodily injury or death.
General Safety WARNINGS!
You and any other operator of this wood chipper + shredder
must read, understand, and follow these instructions in
their entirety. Failure to follow these instructions may result
in ELECTRIC SHOCK, FIRE, and/or serious PERSONAL
INJURY.
Notice the personal safety alert symbol
manual to draw your attention to a WARNING given along
with the particular operating instruction. This means that
the operation requires special ATTENTION, CAUTION, and
AWARENESS.
m
WARNING!
Wear appropriate personal hearing
protection during use. Under some conditions and duration of
use, noise from this product may contribute to hearing loss.
m
WARNING!
The rotating blades can cut you. Keep
hands and feet away from the hopper and the discharge chute.
Before using the wood chipper + shredder, familiarize yourself
with the controls, especially how to stop the unit in an
emergency. The only individuals who should use the wood
chipper + shredder are those who thoroughly understand
these instructions and know how to properly operate the unit.
Children should never be allowed access to the wood chipper
+ shredder.
Retain this manual for future reference and reread it at the start
of each chipping season.
General Safety
1. Avoid dangerous environments – Do not use the wood
chipper + shredder in rain or in damp or wet locations. Do
not operate the unit in gaseous or explosive atmospheres
or use the unit near flammable or combustible liquids.
© 2016 by Snow Joe
, LLC
®
All rights reserved. Original instructions.
15-AMP ELECTRIC
WOOD CHIPPER + SHREDDER
Model CJ602E
m
used in this
Motors in these tools normally spark, and the sparks
might ignite fumes.
2. Dress properly – Do not wear loose clothing or jewelry as
such articles can become caught in moving parts. Wear
a protective covering to contain long hair. Wearing rubber
gloves and substantial non-slip footwear is recommended
when working outdoors.
3. Use safety glasses – Also use dust mask, safety
footwear, snug-fitting clothing, protective gloves, hearing,
and head protection.
4. Extension cords – To prevent electric shock, use only
with an extension cord suitable for outdoor use.
5. Disconnect the tool – Disconnect the wood chipper +
shredder from the power supply when it is not in use,
before servicing it, when changing accessories, and when
performing any other maintenance task.
6. Do not abuse the cord – Never carry the wood chipper
+ shredder by the cord or yank the cord to disconnect it
from the receptacle. Keep the cord away from heat, oil,
and sharp edges.
7. Stay alert – Watch what you are doing. Use common
sense. Do not operate the wood chipper + shredder when
you are tired or under the influence of drugs, alcohol, or
other medication.
8. Store idle tool indoors – When not in use, the wood
chipper + shredder should be stored indoors in a dry and
high or locked-up place out of the reach of children.
9. Maintain the wood chipper + shredder with care –
Keep the cutting edges sharp and clean for optimal
performance and to reduce the risk of injury. Inspect the
extension cord periodically and immediately replace it
if damaged. Keep the handles dry, clean, and free from
oil and grease. Follow the additional recommendations
described in the Care + Maintenance section of this
manual.
10. Check for damaged parts – Before further use of the
appliance, a part that is damaged should be carefully
checked to determine that it will operate properly and
perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts,
mounting, and any other condition that may affect its
operation. A part that is damaged should be properly
repaired or replaced.
11. Lighting – Only operate your wood chipper + shredder in
daylight or good artificial light.
SAVE THESE INSTRUCTIONS
1
Form No. SJ-CJ602E-880E-M
OPERATOR'S MANUAL

Advertisement

Table of Contents
loading

Summary of Contents for SNOWJOE sunjoe CJ602E-RED

  • Page 1 15-AMP ELECTRIC WOOD CHIPPER + SHREDDER Model CJ602E Form No. SJ-CJ602E-880E-M OPERATOR’S MANUAL A Division of Snow Joe , LLC ® IMPORTANT! Motors in these tools normally spark, and the sparks might ignite fumes. Safety Instructions 2. Dress properly – Do not wear loose clothing or jewelry as such articles can become caught in moving parts.
  • Page 2: Personal Safety

    WARNING! 12. Do not overreach – Keep proper footing and balance at Never reach into the hopper until the all times. wood chipper + shredder has come to a complete stop and 13. Never leave a running tool unattended – Turn the is unplugged.
  • Page 3: Electric Safety

    Electric Safety polarized wall outlet. The extension cord plug will fit into the polarized wall outlet only one way. If the plug does not fit fully into the wall outlet, reverse the plug. If the plug 1. Ground fault circuit interrupter (GFCI) protection should still does not fit, contact a qualified electrician to install be provided on the circuit(s) or outlet(s) to be used for the proper wall outlet.
  • Page 4: Double-Insulated Appliances

    Double-Insulated Appliances In a double-insulated appliance, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated appliance, nor should a means for grounding be added to the appliance. Servicing a double- insulated appliance requires extreme care and knowledge of the system, and should be performed only by qualified service personnel at an authorized Snow Joe + Sun Joe...
  • Page 5: Safety Symbols

    Safety Symbols The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate. Symbols Descriptions Symbols Descriptions READ THE OPERATOR'S MANUAL(S) – Read, understand, SAFETY ALERT –...
  • Page 6: Technical Data

    Know Your Electric Wood Chipper + Shredder Read the owner’s manual and safety instructions carefully before operating the electric wood chipper + shredder. Compare the illustration below to the electric wood chipper + shredder in order to become familiar with the location of the various controls and adjustments.
  • Page 7: Carton Contents

    Unpacking 2. Insert the wheel axle into the shredder stand assembly, and re-assemble the shaft sleeve and the support cover (Fig. 2). Carton Contents • Electric wood chipper + shredder main body with hopper Fig. 2 • Electric wood chipper + shredder stand assembly Shaft sleeve Wheel axle Support cover...
  • Page 8: Operation

    Fitting the Paddle Holder and the Paddle Wheel Fig. 5 1. Stand the unit up, and clip the paddle holder to the standing assembly (Fig. 8). Fig. 8 Standing assembly Wheel cover Paddle holder 6. Repeat the steps 2 – 4 to assemble the other wheel. Stand Assembly Fitting 1.
  • Page 9 3. To power the wood chipper + shredder off, push the Fig. 10 removable safety switch to the OFF position. To disable the machine, remove the safety switch completely Hopper (Fig. 13). locking knob Fig. 13 Removable 1. Make sure the removable safety switch is in the OFF safety switch position.
  • Page 10: Overload Protection

    Overload Protection 2. Use the paddle to push the material inside the hopper if needed (Fig. 15). Your electric wood chipper + shredder is designed with overload protection. If the shredder is clogged during Fig. 15 shredding, the overload protection will cut the power automatically to protect your shredder.
  • Page 11: Cutting Blade Replacement

    1. Stop the motor and disconnect the unit from the power Fig. 17 supply. 2. Unscrew the hopper locking knob counterclockwise to open the hopper (Fig. 17). 3. Align the cutting head past the splash guard so that the blade bolts can be removed; secure the cutting head Hopper from rotating by inserting a rod (e.g.
  • Page 12: Model + Serial Numbers

    Storage Follow the steps below to prepare the electric wood chipper + shredder for storage: 1. Disconnect the power supply to the wood chipper + shredder. 2. Clean the wood chipper + shredder with a damp cloth or hand brush. 3.
  • Page 13: Troubleshooting

    Troubleshooting Possible Cause Problem Remedy Motor does not run • Power failure/unit not plugged into a • Check to make sure unit is plugged into a working receptacle. working outlet. Make sure extension cord is not damaged. • The overload protection has responded.
  • Page 14 Optional Accessories WARNING! ALWAYS use only authorized Snow Joe + Sun Joe replacement parts and accessories. NEVER use ® ® replacement parts or accessories that are not intended for use with this tool. Contact Snow Joe + Sun Joe if you are unsure ®...

This manual is also suitable for:

Sunjoe cj602e

Table of Contents