Philips CEM200/51 Quick Start Manual

Register your product and get support at
ENG Quick Start Guide
© 2009 Koninklijke Philips Electronics N.V.
All rights reserved.
CEM200_51_QSG_V1.1
CEM200
1
a b c
e f g
2
3 4
a
c
AMP
b
Overview of parts 1
For cars without ISO connectors
These are the supplied parts needed to
connect and install this unit. Caution
a In-car audio system
• Be sure to connect the black ground (earth) lead
first.
b Sleeve
c Front panel
1
Connect the antenna and amplifier as
d Standard connector
illustrated, if applicable.
e Trim plate 2
Cut off the bigger end of the supplied stan-
dard connector.
f Rubber cushion
3
g Disassembly tools Check the car's wiring carefully and connect
them to the supplied standard connector.
h Screws 4 pieces
4
Connect the supplied standard connector to
the unit.
Connect wires
1 Green/black strip
2 White/black strip
Caution
3 Gray/black strip
• Ensure that all loose leads are insulated with
4 Purple/black strip
electrical tape.
For cars with ISO connectors
2 3
e RED
1
Pull out the ISO connectors from car
dashboard and connect them to the bigger f BLUE
end of the supplied standard connector.
2
Connect the other end of the supplied stan-
g BLACK
dard connector to the unit.
h Orange
3
Connect the antenna and amplifier as il-
i YELLOW To the +12V car battery which is
lustrated, if applicable. You can connect the
car audio to the amplifier through RCA-TO-
RCA cables (not supplied).
Note
Connector Connect to
•
Check wire connection before you mount the unit
1 ANTENNA Antenna
into a car.
2 REAR LINE OUT R Rear right speaker
• If preset radio stations are lost when the ignition
key is turned OFF and then back ON, reconnect
3 REAR LINE OUT L Rear left speaker
the red leads crosswise to the yellow ones.
5
d
h
a a
a
b
c
d
a
b b
b
c
d
e
c
f c
g
h
i
d d
Attach the front panel 5
3 4
1
Attach the trim plate.
2
Insert the right side of the panel in the
chassis until it is correctly engaged.
3
Press the left side of the panel and point the
left hole at the left pillar.
4
Release the panel to engage the left side.
Mount in the dashboard 5
1
If the car does not have an on-board drive or
navigation computer, disconnect the negative
terminal of the car battery.
• If you disconnect the car battery in a car
that has an on-board drive or navigation
Left speaker (Rear)
computer, the computer may lose its
Left speaker (Front)
memory.
Right speaker (Front) • If the car battery is not disconnected,
to avoid short-circuit, ensure that bare
Right speaker (Rear)
wires do not touch each other.
2
Remove the two screws on the top of the
Ignition key +12V DC when
unit.
ON/ACC
3
Remove the mounting sleeve with the sup-
Motor/electric antenna relay
plied disassembly tools.
control lead/Amplifier relay
control lead 4
Ensure that car dashboard opening is within
Ground these measurements:
Illumination switch 5
Install the sleeve into the dashboard and
bend the tabs outward to fix the sleeve.
energized at all times
6
Place the rubber cushion over the end of the
bolt.
7
Slide the unit into the dashboard until you
hear a click sound.
8
Reconnect the negative terminal of the car
battery.
Turn on Play audio files
1 1
Press z to turn on the unit. Press on the front panel to release the
• To turn off the unit, press z for 3 panel.
seconds.
2
Insert a CD with the printed side facing up.
3
Close the panel.
Set clock
Play starts automatically.
»
1
Press MENU/DISP for 3 seconds. • To pause CD play, press 1
2 • To resume CD play, press
Press or repeatedly to until the cur-
rently time is displayed.
3
Turn z clockwise to set hour.
4
Press z to confirm.
5
Turn z anti-clockwise to set minute.
6
Press z to confirm.
View clock
1
Press MENU/DISP repeatedly until the clock
is displayed.
Listen to radio
1
Press SOURCE repeatedly to select Radio.
2
Press 3 or 4 to select band: [FM1], [FM2],
[FM3], [AM1], or [AM2] .
3
Press or to tune to a radio station
manually.
The radio station is broadcast.
»
• To search for a radio station
automatically, press / for 3 seconds.
.
1
again.